1. DL manuals
  2. Smarteh
  3. Controller
  4. LPC-2.MC9
  5. User Manual

Smarteh LPC-2.MC9 User Manual

Manual is about: Longo programmable controller

Summary of LPC-2.MC9

  • Page 1

    User manual longo programmable controller lpc-2.Mc9 main module version 4 smarteh d.O.O. / poljubinj 114 / 5220 tolmin / slovenia / tel.: +386(0) 388 44 00 / e-mail: info@smarteh.Si / www.Smarteh.Si.

  • Page 2

    Longo programmable controller lpc-2.Mc9 written by smarteh d.O.O. Copyright © 2017, smarteh d.O.O. User manual document version: 4 april, 2017 i.

  • Page 3

    Longo programmable controller lpc-2.Mc9 standards and provisions: standards, recommendations, regulations and provisions of the country in which the devices will operate, must be considered while planning and setting up electrical devices. Work on 100 .. 240 v ac network is allowed for authorized pe...

  • Page 4

    Longo programmable controller lpc-2.Mc9 longo programmable controller lpc-2.Mc9 1 abbreviations................................................................................1 2 description...................................................................................2 3 features..................

  • Page 5: 1 Abbreviations

    Longo programmable controller lpc-2.Mc9 1 abbreviations som system on module arm advanced risc machines tcp transmission control protocol iec international electrotechnical commission can controller area network led light emmiting diode 1.

  • Page 6: 2 Description

    Longo programmable controller lpc-2.Mc9 2 description lpc-2.Mc9 smarteh flagship controller offers improved performance, scalability and a wide range of new features within a single compact som based package. Simple and innovative concept, where most competitors require multiple products to deliver ...

  • Page 7: 3 Features

    Longo programmable controller lpc-2.Mc9 3 features figure 1: lpc-2.Mc9 module table 1: features real time linux os arm based main module ethernet connectivity with modbus tcp/ip master and slave, web server and ssl modbus rtu master usb port for debugging, application and default parameters transfer...

  • Page 8: 4 Operation

    Longo programmable controller lpc-2.Mc9 4 operation after installation done only by qualified persons lpc-2.Mc9 main module must be configured and programmed with the appropriate user program using smarteh ide software. Smarteh ide software allows user to configure main module to its own requirement...

  • Page 9

    Longo programmable controller lpc-2.Mc9 example2: network with 1 master and 4 slaves, every slave have defined 4 byte of data and baud rate 250 kbps. Fastest cycle time for this configuration is 5 ms. 5 millisecond is the fastest recommended cycle time. It is recommended to power-up all the nodes on...

  • Page 10

    Longo programmable controller lpc-2.Mc9 with smarteh ide also in run mode is possible to stop executing program and change the application. Sd card the memory card is used for data storage. 6.

  • Page 11: 5 Installation

    Longo programmable controller lpc-2.Mc9 5 installation 5.1 connection scheme figure 3: connection scheme 7.

  • Page 12

    Longo programmable controller lpc-2.Mc9 table 2: can1 & can2 can1.7 can low (master) 0 .. 5 v can1.8 can high (master) .9 ⏊ reference point 0 v can2.10 can low (slave) 0 .. 5 v can2.11 can high (slave) table 3: com2 com2.4 a rs-485 signal com2.5 b rs-485 signal .6 ⏊ ⏊ gnd table 4: switches s3 can te...

  • Page 13

    Longo programmable controller lpc-2.Mc9 5.2 mounting instructions figure 4: housing dimensions dimensions in milimeters. Recommendation on switch or circuit-breaker protection: there should be two poles main switch in the installation in order to switch off the module. The switch must meet the requi...

  • Page 14

    Longo programmable controller lpc-2.Mc9 mounting instructions: 1. Switch off main power supply. 2. Mount module to the provided place inside an electrical panel (din en50022-35 rail mounting). 3. Mount other io modules (if required). Mount each module to the din rail first, then attach modules toget...

  • Page 15

    Longo programmable controller lpc-2.Mc9 5.3 module labeling figure 6: labels label 1(sample): label 2(sample): label 1 description: 1. Lpc-2.Mc9 is the full product name. 2. P/n: 225mc915001001 is the part number. • 225– general code for product family, • mc9 – short product name, • 15001 – sequence...

  • Page 16: 6 Technical Specifications

    Longo programmable controller lpc-2.Mc9 6 technical specifications table 6: technical specifications rated power supply 100/240 v ac, 50/60 hz operational power supply 90 .. 264 v ac power consumption up to 24 w depending on additional modules connected to main module connection type screw type conn...

  • Page 17: 7 Spare Parts

    Longo programmable controller lpc-2.Mc9 7 spare parts for ordering spare parts following part numbers should be used: lpc-2.Mc9 main module lpc-2.Mc9 p/n: 225mc915001001 13.

  • Page 18: 8 Changes

    Longo programmable controller lpc-2.Mc9 8 changes the following table describes all the changes to the document. Date v. Description 15.04.17 4 rtu update. 15.01.17 3 added technical specifications. 16.11.16 2 added technical specifications. 30.09.16 1 the initial version, issued as lpc-2.Mc9 user m...

  • Page 19: 9 Notes

    Longo programmable controller lpc-2.Mc9 9 notes 15.