1. DL manuals
  2. SmartLab
  3. Pedometer
  4. Walk P+
  5. User Manual

SmartLab Walk P+ User Manual

Manual is about: 3-D Step-counter with wireless data transfer

Summary of Walk P+

  • Page 1

    23 engli sh hmm diagnostics gmbh d-69221 dossenheim, germany www.Hmm.Info please read this user manual thoroughly before first using this device 3-d step-counter with wireless data transfer user manual.

  • Page 2: Content

    24 content i. Introduction 25 ii. Your smartlab ® walk p+ 26 display & functions 26 specifications 26 iii. Setup & functions 27 inserting the battery 27 mounting the carrying cord 28 before first use 29 setting weight, step length, signal tone und time 29 manually transfer not sent data 35 manually ...

  • Page 3: I. Introduction

    25 engli sh i. Introduction thank you for using the smartlab ® walk p+ 3-d step counter. Because of its small and handy form and its appealing design, this device suits best your needs for the control of walked distances. Because of the integrated 3-d sensor technology, this device counts normal ste...

  • Page 4: II. Your Smartlab

    26 ii. Your smartlab ® walk p+ display & functions specifications 1. Name: smartlab ® walk p+ 2. Size: 70 x 37 x 10,5 mm 3. Weight: 30 g 4. Battery: 1 x cr 2032 battery 5. Unit for steps walked: amount 6. Unit for calories: kcal 7. Unit for distance: km 8. Unit weight: kg / lb (adjustable) 9. Commun...

  • Page 5: III. Setup & Functions

    27 engli sh iii. Setup & functions inserting the battery in order to change/ insert the battery, you need to unscrew the battery lid on the back of the device. Place the coin cell with the plus side to top into the opening. If you change the battery, use the screwdriver to lever off the battery. Aft...

  • Page 6: Mounting The Carrying Cord

    28 mounting the carrying cord you can wear your smartlab ® walk p+ with the carrying cord included in the set. To do so, you will have to connect the cord to the device by doing the following steps: push the thin end of the cord through the two tiny eyes at the back side of the device. Pushing toget...

  • Page 7: Before First Use:

    29 engli sh before first use: before first using your smartlab ® walk p+ step counter, please hold the „disp/set“ button pressed for more than 3 seconds. The device will go on and enters the setting mode. The smartlab ® walk p+ step counter has an automatic setup function (heart beat). This way ther...

  • Page 8: Smartlab

    30 with the “m/” button you can adjust your weight. You can only increase the value. After reaching the maximum level of 200 kg, smartlab ® walk p+ will start with 30 kg again. By keeping the “m/” button pushed, the weight value increases faster. After having set your personal weight, press „disp/...

  • Page 9: Setting Time:

    31 engli sh setting time: after that, your device enters the time setting mode. Press the “m/” button in order to switch between the two display modes 12h and 24h (24h mode is preset). By pushing „disp/ set“ button you can set the time. First you set the hours by pushing the “m/” button. Confirm b...

  • Page 10: Setting Date:

    32 setting date: after that, your device enters the date setting mode. Press the “m/” button to enter the current day (display shows “d”) and confirm with “disp/ set”. Proceed accordingly for setting the month (display shows “m”) and year (display shows “y”). Always confirm with “disp/ set”. Note: ...

  • Page 11

    33 engli sh 1. Per 10 minutes mode (recommended) 2. Heart beat mode setting the per 10 minutes ant mode: in this mode data will be sent out every 10 minutes to the accordant receiving device. All data which was stored during the last time interval will be sent out then. You can see the automatic mod...

  • Page 12: Setting The Heart Beat Mode:

    34 setting the heart beat mode: if this mode is (on), which is the factory setting, the step counter will try to communicate every minute with receivng device. Is there any receiving device in reach which supports this function, the step counter will be set automatically. After the step counter was ...

  • Page 13: Smartlab

    35 engli sh manually transfer not sent data you can also manually trigger data transfer to the receiving device. To do so, you first have to turn on send mode on your smartlab ® walk p+device. Please quickly press and release the “disp/ set” button, and then press it again for 6 seconds. In the uppe...

  • Page 14: Manually Transfer All Data

    36 manually transfer all data you can also manually trigger all data transfer to the receiving device. To do so, you first have to turn on send mode on your smartlab ® walk p+device. Please quickly press and release the “disp/ set” button, and then press it again for 6 seconds. In the upper display ...

  • Page 15

    37 engli sh pict. 09 pict. 10 pict. 11.

  • Page 16: Starting Up

    38 starting up • after having set time and step length, you can use your smartlab ® walk p+ step counter. Just take the device and start walking. The device will turn on automatically when it registeres a movement. The display will read “hello” • after the 10 th step, the counter starts counting you...

  • Page 17: Additional Functions

    39 engli sh step count, total distance, the time of your exercise and the calory consumption. Note: once you have walked 99999 steps, the device stops counting your steps. The lcd display will start twinkling and reset after the time setting was set back to 0:00. Additional functions battery-display...

  • Page 18: Locking Your Device:

    40 locking your device: if no button is pushed for 30 seconds, your smartlab ® walk p+automatically activates key lock. This is shown by the according display symbol. By pushing the „disp/ set“ button, you can unlock the device. Display-power-off: when you are in user mode, your device automatically...

  • Page 19: Regularity and Safety Notice

    41 engli sh regularity and safety notice declaration of conformity this product is compliant with the ec directives: -1999/5/ec safety statement this product has been verified to conform to the safety certification in accordance with the specification of en standards: en 60950-1:2006 + a11:2009 + a1...

  • Page 20: Rohs Compliance

    42 rohs compliance this product complies with directive 2002/95/ec of the european parliament and the council of 27th january 2003 regarding the limited use of dangerous substances in electrical and electronic equipment (rohs) and its variations. The weee logo on the product and the packaging indica...

  • Page 21: Warranty

    43 engli sh warranty hmm diagnostics gmbh products need to fulfill high quality requirements. Because of this reason, hmm diagnostics gmbh gives a 2-year warranty by purchasing this smartlab ® product. You can even extend the warranty from 3 to 5 years without extra pay when you register your produc...

  • Page 22: Www.Smartlab.Org

    44 hmm diagnostics gmbh friedrichstr. 89 d-69221 dossenheim, germany e-mail: info@hmm.Info www.Hmm.Info hersteller/manufacturer: weitere informationen zu den smartlab ® produkten / more information on our smartlab ® products: www.Smartlab.Org.