Summary of Series-1
Page 1
Smartmow series-1 the smarter way to mow your lawn! © user manual.
Page 2
Safety instructions please read the following instructions carefully before use. Warnings: 1. Do not modify the shape, dismantle or reconfigure the device, or you may run the risk of causing a fire, mechanical fault or personal injury. 2. Do not start your smartmow on a wet lawn, as it may damage th...
Page 3
13. Only the battery provided or approved by robolabs, inc.. 14. Only use the electrical power indicated on the label. 15. Only use the smartmow charger and base station. 16. The waste battery should be handled in a professional way. 17. Before using the smartmow, pick up objects like branches, ston...
Page 4
Product description 1. The robot mower( smartmow series-1 ) 2. Ic card 3. Base station 4. Power supply 5. Base station stakes 6. Height adjuster 7. Perimeter wire 8. Pegs 9. Remote control 10. Batteries for remote control optional accessories: perimeter wire (100 m) pegs (100 pcs) blades (11 cm* 3 p...
Page 5
Technical specifications power supply: input: 100-240v 50/60hz output: 30v 2000ma mower battery: 24v 8ah average power: 70w brief introduction of smartmow series-1 the smartmow uses advanced environmental-friendly rechargeable li- batteries. Smartmow mainly adapts to lawn care of family and public l...
Page 6
Important ensure the minimum distance: 30cm (from the perimeter wire to the obstacles besides the lawn) ensure the bending angle of the wire at least 100 degree pull the perimeter wire as straight as possible. Do the following: fasten and hold the perimeter wire to the ground, below the grass level ...
Page 7
The base station important ensure that the base station is put at the open area where is also easy to connect to the electricity outlets. Ensure that the base station is placed in clockwise direction along the perimeter wire connect the ends of the perimeter wire to holes of the base station. There ...
Page 8
Put two pieces of height adjusters at the bottom of the base station. Connect the ends of the perimeter wire to holes of the base station..
Page 9
The perimeter wire goes along the wireways and through the center of the bottom. Fix the base station with the stakes..
Page 10
Then after, the base station looks as follows: ▲ the power supply connects to the base station and the electricity outlets respectively. ▲ use the electrical power indicated on the label only. If you are not sure about the power type, please inquire the located electricity generating board. ▲ use th...
Page 11
Manual charging: be sure that the power is off. After taking off the rubber- isolator, connect one side of the charger to mower, the other to the electricity outlets. When the charger is in motion, the led of the charger is red, and it turns to green when fully charged..
Page 12
Before cutting 1. Pick up debris (branches, stones) before you start to mow your lawn. 2. The robot mower works only in the scope of the area rounded by the perimeter wire. Ensure that you have buried the wire well. 3. Observe the mower in use for the first time. Be sure that it won’t get trapped in...
Page 13
Now the machine is in motion, use the ic card in the induction place and you will hear a sound and then the mower starts to work. Power off press the ‘power off’ button to stop the machine. The functions of the remote control 1. Turn left 2. Go back to the base station for charging 3. Turn right 4. ...
Page 14
▲ try not to use the remote control when the mower is moving on or near the perimeter wire. ▲ the battery type is 12v27a, and it is for the remote control use only. Adjusting of cutting height the mower has 3 blades working together. The blades are fixed on the adapter with flexible shims. The lowes...
Page 15
The sequence of installation is: blades and adapter, shims, inner hex screws please fix the screws tightly after adjusting. You can also take apart the outer big wheel to use the inner small ones to adjust the cutting height.
Page 16
Instructions for quick operation prepare the area before cutting, according to the instructions for the perimeter wire and base station. The perimeter wire bury the perimeter wire according to the shape of the lawn. If there are walls, fences or steps besides the lawn, then the minimum distance from...
Page 17
The base station place the base station in the open area where it is easy to connect to electricity outlets. Install the height adjuster first and then connect the two ends of the perimeter wire to the base station. Be sure that the wire goes through the right center of the station’s bottom. There s...
Page 18
Reference information troubleshooting problems possible reasons solutions the mower moves out of the area rounded by the perimeter wire or moves in circle searching for the perimeter wire the perimeter wire fails to send signals be sure the perimeter wire is connected to the base station that is in ...
Page 19
Warranty and information on service this guarantee does not cover normal wear and tear, damage caused by overloading, negligence, accident or improper use. Any change or modification made by the purchaser will invalidate the guarantee, as would any attempted repair. The guarantee applies only when t...