2 if you have any assembly issues or are missing a part, please call us for assistance. Our smartrike® assembly experts will assist you. Do not return to the store 1-855-smtrkus (1-855-768-7587) please call look us up on youtube: www.Youtube.Com/smarttrikeofficial 620 20010008620 b 20010004620 c 200...
Step 1 parts needed to complete this section b a o x2 pull out plastic tabs from each rear wheel (a1) until the wheel cover opens. Take out white plugs+ screws (a3). 1 a 1 b 1 c a1 a2 2 1 place the washer (o) on the axle (as shown) connect each back wheel (a) to back axle.
Step 2 parts needed to complete this section p a a3 a1 x2 x2 by using the phillips screwdriver (p), screw part a3 into part a firmly tighten clockwise. Click! Click! Click! Firmly insert white plug (a3) into axle opening, as shown. Align spring lock with dropout hole in axle and push firmly into pos...
Step 3 parts needed to complete this section d c insert part d into part b all the way through the hole (as shown) insert part d into part c all the way, until the spring meets the retaining head (as shown) 3 a 3 b.
Step 4 4 a 4 b push the apple firmly down to insert, slightly turn until you hear a "click". Make sure white connector is not visible. 4 c click! Click! Click! 2 1 push the red button and simultaneously turn the wheel 180º until you hear a 'click'. Push down on the handlebar. There should be no spac...
Step 5 parts needed to complete this section p 5 a 5 b gg e take the seat (e), push the screw through the seat & the seat belt (gg). Screw into the most rear facing hole and firmly tighten with allen key (p). By using the "allen" key (p), remove screw by turning counter clockwise..
Step 6 parts needed to complete this section f 6 a 6 b click! Click! Place safety bar holes into protrusions located at the back of the seat. With little force, push part f into the apple's holes until you hear a "click"..
Step 7 parts needed to complete this section g 7 a 7 b 7 c connect headrest (g) into designated slots on safety bar (as shown), until you hear a "click". Hook cords, located on both sides of the seat cover, onto back seat protrusions. Warning: it may be dangerous to leave your child unattended. Use ...
Step 8 parts needed to complete this section h attach both sides of the canopy (h) into designated slots on head rest (g), until you hear a "click". 8 a click!.
Step 9 parts needed to complete this section p i attach basket firmly to vertical frame (as shown), use removed screw and turn clockwise until secured. Push basket (i) firmly on to rear axle until it "clicks" into position (see 1 & 2). Click! Click! 2 1 9 a 9 c 9 b by using the phillips screwdriver ...
Step 10 parts needed to complete this section k j remove the screw from part j by turning counter clockwise. Insert part k into part j. Align the hole in part k with the correct hole in part j. Use phillips screwdriver (p) to attach. 10 a 10 b 10 c.
Step 11 parts needed to complete this section j k remove the securing pin with securing lock, as shown. Insert pin with safety lock, as shown. Insert the assembled parent handle (k) into the retaining hole on rear of trike. 11 a 11 c 11 b click! 11 d warning: make sure safety pin is inserted correct...
For the 10+ month stage, open the footrests by pulling it down. Pull down both sides of the footrest. 12 a 12 b step 12.
Parent control 10 m + when the clutch is pulled away from the wheel there is no pedal control and the wheel is in a free mode position..
Child control 1 2 3 1 1 2 2 1 2 1 1 2.
1 2 for the 24+ months stage, fold up left and right footrest. 4a 62027841603 10m+ 18m+ 30-36m 24m+ 2 1 push release button to place it back into frame (as shown). When the clutch is pushed closed and aligned with the front wheel, child has pedal control. 5 4b.
