SmartShopper 301 Quick Start Manual
TM
TM
The SmartShopper is a “voice activated” grocery shopping assistant.
You will be able to input grocery store items throughout the week
as you need them.
The SmartShopper is pre-loaded with over 2500 grocery store items.
In addition to food and beverage you will also find household items,
cleaning and beauty supplies, office and school supplies, etc.
The SmartShopper also has an errand feature. Before leaving for
the grocery store you can input common errands that you may need
to run such as: bank, car wash, dry cleaners, etc. See the
vocabulary list for a full listing of errands.
SmartShopper can be adhered to the fridge* (built-in magnets), attached to
a wall (see mounting instructions below), or used on the countertop (rubber
feet prevent it from sliding or scratching surfaces).
*Note: SmartShopper will not adhere to stainless steel appliances.
Insert 1 plastic molly and screw at eye level of the primary user
Open the printer door
by pulling on the lip on
the door.
To Order Replacement Paper Packs:
Go to www.SmartShopperUSA.com or send a check for $10.99 to:
SmartShopper Electronics, LLC
7777 Wall Street Suite #3
Valley View, OH 44125
Uses Paper Replacement Pack #PR102
Remove the used
paper roll. Insert a
new roll with paper
dispensing over the
top as shown.
Close the printer
door. Be sure to
leave 1/2 inch of
paper exposed.
Insert the second molly and screw 1 3/8” directly across from
the first hole (in an exact straight line).
Tighten both screws, leaving the head of each 1/4” out from the wall
Line up the SmartShopper holes on the back of the unit with the screws
Push the unit in toward the wall and down to lock into place
Open the battery door on the back of the
SmartShopper by pressing on the release tab.
Insert
4 AA
batteries (as shown) and close
the battery door.
Insert Batteries
Problem:
Won’t print
Prints blank pages
Screen is always blank
The screen appears
to be “frozen”
Voice recognition is
not working
Some words aren’t
being recognized
when I say them
Some words aren’t
being recognized
when I say them
Magnets won’t stick
to my refrigerator
For additional help, visit our website at
www.SmartShopperUSA.com
If you cannot resolve your issue, please call 1-866-369-8585
Possible cause:
Paper jam
Paper inserted incorrectly
Batteries are dead
The unit is locked up
Microphone settings
not adjusted correctly
Items are not in the
SmartShopper library
The item is in the library, but
Voice Recognition needs
additional training
Refrigerator is stainless steel
or other non-magnetic material
You should:
Remove and reinsert paper roll.
Remove paper roll, flip paper,
reinsert roll.
Replace batteries
Reset by pressing the List and Down Arrow
at the same time. Press Select to Resume.
Select a different mic setting from
the setup menu (see reverse side)
See “Adding custom items to the library”
(reverse side)
If it is in the booklet and the unit fails
to recognize it, you can train SmartShopper
using your own voice. See "Improving
recognition of items" section (reverse side).
Use wall mounting kit instead
(see wall mounting kit instructions)
Inserting Paper Rolls
Troubleshooting
Setup Instructions
What’s in the box?
Wall Mounting Kit (Optional)
SmartShopper is now ready to use!
SmartShopper
Unit
1 Roll of Paper
(in unit)
Wall Mount
Kit
Quick Start Guide
(what you are reading
right now)
Warranty
Sheet
© Copyright SmartShopper Electronics, Inc. 2006. All rights reserved. SmartShopper™ is a trademark
of SmartShopper Electronics, Inc. Other trademarks or registered trademarks are the property of their
respective manufacturers or owners. Price and specifications are subject to changes without notice.
See inside package for warranty details.
Please
READ THESE INSTRUCTIONS
before
attempting to use your new SmartShopper.
TM
Key Guide
Quick Start Guide for Model #301
RECORD
RECORD
LIST
TIMER
TIMER
LIST
SELECT
UP
DOWN
SELECT
RECORD
Master Library
Booklet