- DL manuals
- SmartTrunk Systems
- Transceiver
- ST-1000C
- User Manual
SmartTrunk Systems ST-1000C User Manual
Summary of ST-1000C
Page 1
Uhf fm digital transceiver st-1000d st-1000c vhf fm digital transceiver st-1000v smartrunk systems, inc. St-1000um r1.0a printed in malaysia pn: al1000010a.
Page 2: Fcc Notice
Page 2 federal communications commission interference statement this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a resident...
Page 3: Warning:
Page 3 thank you! We are grateful you chose smartrunk for your land mobile radio applications. We believe this powerful, flexible and easy-to-use transceiver will provide dependable and reliable communications to keep personnel operating at peak efficiency. Smartrunk transceivers incorporate the lat...
Page 4: Attention (U.S.A. Only):
Page 4 attention (u.S.A. Only): the rbrc recycle seal found on smartrunk lithium-ion (li- ion) battery packs indicates smartrunk‘s voluntary participation in an industry program to collect and recycle li-io batteries after their operating life has expired. The rbrc program is an alternative to dispo...
Page 5: Contents
Page 5 contents contents page appendix i: dealer programmed functions ….19 battery charger....................................................................... 9 getting acquainted .............................................................. 13 installing the antenna st-fa0x .......................
Page 6: Supplied Accessories
Page 6 unpacking and checking equipment note: the following unpacking instructions are for use by your smartrunk dealer, an authorized smartrunk service facility, or the factory. Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before discardin...
Page 7: Battery Pack
Page 7 smartrunk st-b16 battery pack recommendations if not charged or used correctly, lithium polymer batteries may ignite without warning and cause serious injury and property damage. If you are unable to follow the safety recommendations then do not use them do not charge lithium polymer cells on...
Page 8
Page 8 battery and connectors for even the smallest damage. Caution: cells may be hot! Do not allow the electrolyte to get into eyes or on skin. Wash affected areas immediately if get in contact with electrolyte. Do not alter or modify connectors or wires of a lithium polymer battery pack. Never inc...
Page 9: Battery Charger
Page 9 smartrunk bc-02 battery charger never leave the charger unattended. If you will be away from the charger then leave it unconnected from the battery. Charge all batteries on concrete, at least 10 feet (3 meters) away from combustible materials. Do not use if flammable liquids are in the area. ...
Page 10: Operation:
Page 10 the battery charger st-bc02 is a device specially designed to recharge sbp-16 battery pack compatible with st-1000 sdr radio. This device has enough internal intelligence to exchange information with the battery under charge and improves charging regulation to extend battery life as much as ...
Page 11: End Of Charge:
Page 11 end of charge: as soon as the re-charge process has been completed the charger led becomes green. You can decide when the performance becomes too poor to buy a new battery, but anyway, the battery life indicator will let you get an approximate idea of battery health after the charging proces...
Page 12
Page 12 installing/ removing the li-ion battery pack only use the st-b16 battery packs with this transceiver. To install the battery, please complete the following steps. 1- match the grooves of the battery pack with the corresponding holes on the back of the transceiver. 2- pull the battery pack do...
Page 13: Rotary Encoder
Page 13 getting acquainted 1. Rotary encoder move clockwise or counterclockwise to change the selection according to the mode programmed for this encoder. 2. Power switch and volume control turn clockwise to switch on the transceiver. Rotate to adjust the volume. Turn fully counterclockwise to switc...
Page 14: Transmit/ Busy/ Low Bat
Page 14 3. Transmit/ busy/ low bat lights red during transmission green while receiving a call blinks on red to show low battery status 4. Speaker 5. Microphone 6. Side keys press to activate its programmable function. The function assigned to this key is designed by your dealer. 7. Ptt (push-to-tal...
Page 15
Page 15 rotary functions top rotary switch function can be assigned to different associated functions in your dealer shop. Please check with your dealer the function assigned to this knob. Possible functions are: none: moving this selector do not generate any operation. Channel selector: select curr...
Page 16
Page 16 lights green: while receiving. Flashes red: when the battery power is low, once per 2 second when battery charge is under the 5% and once per second when it’s less than 2%. Switch on/off and volume selector turn clockwise to switch on the transceiver. Rotate to adjust the volume. To switch o...
Page 17
Page 17 position. If your radio is in the end of the list, it will jump to the first channel in your channel table (roll over) channel down: selects the previous channel in the current channel list from current bank. If the rotary is also set for channel selector, this button action will still chang...
Page 18
Page 18 appendix i: dealer programmed functions key short push long push r o tar y eme rg en cy to p s id e eme rg en cy to p s id e fu n ct io n channel up channel down power toggle monitor rssi set hybrid mode cleat hybrid mode.
Page 19
Page 19 copyright 2014 printed in malaysia www.Smartrunk.Com st-1000um r1.0a al1000010a.