1. DL manuals
  2. SMC Networks
  3. Gateway
  4. EZ Connect SMC8511
  5. Install Manual

SMC Networks EZ Connect SMC8511 Install Manual

Manual is about: Cable Modem Gateway

Summary of EZ Connect SMC8511

  • Page 1

    Install guide ez connect™ cable modem gateway - 1 - smc8511.

  • Page 2

    Copyright information furnished by smc networks, inc. (smc) is believed to be accurate and reliable. However, no responsibility is assumed by smc for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or ...

  • Page 3

    Table of contents 1. Smc8511 outdoor cable modem ................................................................................................................ 5 2. Mechanical installation ................................................................................................................

  • Page 4

    5.7.8 check server status .................................................................................................................. 22 5.7.9 authentication of logon attempts.............................................................................................. 22 5.8 troubleshooting ...

  • Page 5

    1. Smc8511 outdoor cable modem figure 1-1 smc8511 outdoor cable modem the smc8511 outdoor cable modem allows catv operators to offer commercial broadband ip data services to customers requiring a hardened docsis 2.0 cable modem suitable for outdoor environments. Applications include traffic light co...

  • Page 6

    Strand clamp 2. Mechanical installation pivot locking bolt pivot bolt note that the housing bolts are pre-torqued at the factory and should not be tightened in the field. Once the up/down tilt is set lock it in place with the up/down tilt locking bolts. Yoke housing bolt hole up/down tilt locking bo...

  • Page 7

    3. Powering methods 3.1 power from catv system catv rf + 60-90 vac power-passing tap smc8511 surge protector smc8511 figure 3-1 power from catv system when the smc8511 is to be catv line powered the tap must be power passing and the attenuator value chosen to present the system standard levels to th...

  • Page 8

    Above configuration (fig 3-2) is particularly useful in a lab/shop environment where docsis is available but without power. A power injector 2 fed with 24 vdc with at least 1 amp capacity powers the smc8511 through the ethernet port. Note: do not exceed 28vdc into the power injector (no 48 vdc injec...

  • Page 9

    4. Smc8511 system description water resistant rj45 connector ethernet switch power conversion and distribution system docsis 2.0 cable modem f connector figure 4-1 smc8511 simplified block diagram 4.1 smc8511 business class outdoor cable modem the simplified block diagram of the smc8511 outdoor cabl...

  • Page 10

    5. Smc8511 business class docsis outdoor cable modem 5.1 features • designed for commercial high speed internet customers • integrated docsis 2.0 cable modem • one block of globally routable static ips assigned to public lan interface • static ip and block of public lan ips enabled via ripv1/2 • alt...

  • Page 11

    5.3 defaults the smc8511 outdoor cable modem (ocm) defaults to the following: • bridge mode • cpe / remote management interface – disabled • web server (gui) o rf interface – enabled on port 80 (http) and 81 (https) o cpe / remote management interface enabled on port 8080 (http) and 8181 (https) • t...

  • Page 12

    5.4 principal operating modes 5.4.1 bridge mode when in bridge mode: • the outdoor cable modem (ocm) only requests an rf interface ip address. • logon to 192.168.100.1 (ethernet interface) or rf interface ip to put ocm into router mode. • cpe (ethernet) interface, static ip and rip are disabled. 5.4...

  • Page 13

    5.5 graphic user interface (gui) to remotely access the gui, point a browser to the rf interface ip. The login screen shown in figure 5-1 will be displayed: figure 5-1 login screen the default username is mso and password is msopassword. Do not give this login information to the customer. - 13 -.

  • Page 14

    When login is complete the status screen as shown in figure 5-2 will be displayed. Navigate the gui via the menu at the left of the screen. Refer to the descriptions of specific fields provided in section 5.6 command line interface. Many of the screens also have extensive help menus which are access...

  • Page 15

    5.6 command line interface (cli) 5.6.1 access the command line interface (cli) ƒ login using telnet ƒ to remotely access the cli, open a command prompt and type: ƒ telnet [remote mgmt port] ƒ example: telnet 12.3.10.6 2323 //specify port (e.G. 2323) default username is mso and the passwordis msopass...

  • Page 16

    5.6.3 verify configuration with ‘script’ command • verify that the gateway is configured correctly with the “script’ command. From the main> prompt enter: script main> script cm_capability rg true cm_capability httpd true remote_management_mso true remote_management_cusadmin false remote_management_...

  • Page 17

    5.6.5 check rf snr and power levels • check rf snr and power levels. From the main> prompt enter: snr main> snr upstream power= 48.00 downstream power=-3.43 snr: 35.35 db 5.6.6 check rf phy status • check rf phy. From the main> prompt enter: phystatus main> phystatus current phy status: downstream f...

  • Page 18

    5.6.7 display rf ip (cable) and cpe / remote management ip (rip src) • display rf ip (cable) and cpe / remote management ip (rip src). From the main> prompt enter: ipcable main> ipcable cable new ip address: 10.0.0.35 rip src ip address: 8.9.3.2 5.6.8 display rip information • display rip informatio...

  • Page 19

    5.7 configure ripv2, static ip, other initial settings 5.7.1 gateway configuration file if a gateway configuration file has been pre-built use ‘setconfig’ to download it. Otherwise, configure the gateway manually with the commands detailed in the following sections. • download gateway configuration ...

  • Page 20

    Ripmd5addkey c specify ‘c’ for cable interface, and key id and key string main> ripmd5addkey c 1 key note: reboot is required to invoke changes. 5.7.4 disable remote access to web server • disable http and https remote access to cpe / remote management interface. From the main> prompt enter: remoteh...

  • Page 22

    5.7.8 check server status • check if in router mode and other settings. From the main> prompt enter: vendor main> vendor version information: model name: smc8004bcm vendor name: smc networks image id: 4561 hardware: 1.A … smc8004bcm capability: rip enabled note “smc8004bcm capability: rip enabled” =...

  • Page 23

    5.8 troubleshooting 5.8.1 ping • ping. From the main> prompt enter: ping [packet size] [repeat count] specify target ip or fqdn with packet size in bytes (optional), specified number of times (optional). Main> ping 216.109.117.107 64 5 ping:pinging 216.109.117.107 with 64 bytes of data ping:echo rep...

  • Page 24

    5.8.3 cpu and rf interface uptime • display cpu utilization, system uptime, rf downstream uptime, and upstream uptime. From the main> prompt enter: rep 1 note: there are 28 reports available. Enabling report levels will consume system resources and may affect data traffic. Disable report levels when...

  • Page 26

    5.8.7 display packet counters • display lan, wan, or purge packet counters. From the main> prompt enter: pktcount [purge] 0 indicates the lan and 1 the wan. Purge clears the counter. Main> pktcount 0 lan interface: ifoutoctets: 226052 ifinoctets: 183758 main> pktcount 1 cable interface: ifoutoctets:...

  • Page 27

    5.9 vendor specific tlvs 5.9.1 tlv in ocm config file option 43 - 27 -.

  • Page 28

    A. Appendix a: smc8511 cli command guide (ver 4.0.0.26) a.1 most commonly used commands setdns syntax: setdns description: set dns primary server and secondary server. Sethttp syntax: sethttp description: enable or disable http server. Note: when disabled, http server is disabled on all interfaces b...

  • Page 29

    A.2 remote management and authentication commands remotehttp syntax: remotehttp description: enable or disable http remote access. Remotehttpport syntax: remotehttpport description: set http remote access port. Remotehttps syntax: remotehttps description: enable or disable https remote access. Remot...

  • Page 31

    A.3 rip commands ripsend syntax: ripsend description: set rip advertisement sending on specified interface. Ripreceive syntax: ripreceive donotrecieve> description: set rip advertisement receiving on specified interface. Ripauthtype syntax: ripauthtype description: set rip authentication type. Ripmd...

  • Page 32

    A.5 show information commands config syntax: config description: display docsis configuration file. Dhcpshow syntax: dhcpshow description: display dhcp client’s ip, mac and status. Dir syntax: dir description: list available modem software versions. Hwcounters syntax: hwcounters description: shows s...

  • Page 34

    Quit syntax: quit description: under remote management mode, quit the cli and continue run cm. Reset syntax: reset [cleanall] description: reboot the cable modem. If there is no parameter, cm would just reboot. Otherwise, if the parameter is "cleanall", cm would do a factory reset. Ex. "reset cleana...

  • Page 37: Smc8511

    - 37 - smc8511 smc networks, inc. 20 mason irvine, ca 92618 rev. 1.0 – 4.3.07.Cap.