Ez connect n draft 11n wireless usb2.0 adapter ez switch™ 16/24-port fast ethernet switch smcfs1601/smcfs2401.
Copyright & trademarks specifications are subject to change without notice. Is a registered trademark of smc technologies co, ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any...
Contents package contents.................................................................................................1 chapter 1 product introduction .......................................................................2 1.1 product overview ......................................................
1 package contents the following contents should be found in your package: ¾ one smcfs1601 /smcfs2401 switch ¾ one power cord ¾ this user guide ¾ mounting screws and two “l” planks ¾ quick installation guide ¾ smc warranty card ¾ four rubber foot pads note: make sure that the package contains the ab...
2 chapter 1 product introduction this chapter describes the features of the model of smcfs1601/smcfs2401 16/24-port 10/100mbps fast ethernet switch. 1.1 product overview smcfs1601/smcfs2401 switch provides 16/24-port 10/100mbps auto- negotiation rj45 ports. Each port of the smcfs1601/smcfs2401 suppo...
3 2.1 front panel the front panel of smcfs2401 consists of switch model, switch led indicators, and 24 10/100mbps rj-45 ports. Figure 2-1 smcfs2401 switch front panel sketch the led indicators include power, link/act led indicators, which are used for monitoring and pre-troubleshooting of the switch...
4 chapter 3 installation 3.1 precautions to ensure a long-term and stable performance of the switch, please pay attention to the following before the installation. 1) safety requirements • before cleaning the switch, cut off the power supply. Do not clean it by the waterish cloth, and never use any ...
5 3.2 installation this switch can be either installed on the standard 19-inch mountable rack or located on the desktop. Caution: please unplug the power cord before installing or removing the switch. 3.2.1 desktop installation to install the switch on the desktop, please follow the steps: 1) set th...
6 3.2.2 rack installation to install the switch in an eia standard-sized, 19-inch rack, follow the instructions described below: 1) secure the supplied rack-mounting brackets to each side of the switch with supplied screws, as illustrated in the following figure. Figure 3-2 attaching brackets 2) aft...
7 3.3 connect to ground connecting the switch to ground is to quickly release the lightning over-voltage and over-current of the switch, which is also a necessary measure to protect the body from electric shock. In different environments, the switch may be grounded differently. The following will in...
8 figure 3-5 * the figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. Note: if you intend to connect the switch to the ground via th...
9 appendix a: specifications general standards ieee 802.3 10base-t, ieee 802.3u 100base-tx topology star protocol csma/cd ethernet: 10mbps (half duplex) 20mbps (fullduplex) data transfer rate fast ethernet: 100mbps (half duplex) 200mbps (full duplex) 10base-t: utp category 3, 4, 5 cable (maximum 100...
10 appendix b: troubleshooting 1. The power led is not lit ¾ make sure the ac power cord connected the switch with power source properly. ¾ make sure the power source is on. 2. The link/act led is not lit when a device is connected to the corresponding port ¾ make sure that the cable connectors are ...
Smcfs1601_2401_ug_20101102_v1 1.Pdf 14 2010-11-30 17:52:37.
Smcfs1601/smcfs2401 7109504046.
