Ez connect n draft 11n wireless usb2.0 adapter ez switch™ 16/24-port gigabit ethernet switch smcgs1601/smcgs2401.
Smcgs1601 /smcgs2401 user manual v1.0
I copyright & trademarks specifications are subject to change without notice. Is a registered trademark of smc technologies co, ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by a...
Ii fcc statement this equipment has been tested and found to comply with the limits for a class a digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. ...
Iii contents package contents ..................................................................................................................... 1 chapter 1 product introduction ............................................................................................. 2 1.1 product overview .....
1 package contents the following contents should be found in your package: ¾ one smcgs1601 /smcgs2401 switch ¾ two power cords (for eu+uk use) ¾ this user guide ¾ mounting screws and two “l” planks ¾ quick installation guide ¾ smc warranty card ¾ four rubber foot pads note: make sure that the packag...
2 chapter 1 product introduction this chapter describes the features of the smcgs1601/smcgs2401 switch. 1.1 product overview the smcgs1601/smcgs2401 switch provides you with a high-performance, low-cost, easy-to-use, seamless and standard upgrade to boost your old network to 1000mbps. Increase the s...
3 chapter 2 identifying external components this chapter describes the front panel, rear panel and led indicators of the switch. Smcgs1601 and smcgs2401 just differ in the number of led indicators and ports and all figures in this guide are of smcgs2401. 2.1 front panel the front panel of smcgs2401 ...
4 cable of ac cord or with ground cable. For detail information, please refer to section 3.3 connect to ground. ¾ ac power socket: connect the female connector of the power cord here, and the male connector to the ac power outlet. Please make sure the voltage of the power supply meets the requiremen...
5 located on the desktop. Caution: please unplug the power cord before installing or removing the switch. 3.2.1 desktop installation to install the switch on the desktop, please follow the steps: 1) set the switch on a flat surface strong enough to support the entire weight of the switch with all fi...
6 1) secure the supplied rack-mounting brackets to each side of the switch with supplied screws, as illustrated in the following figure. Figure 3-2 attaching brackets 2) after the brackets are attached to the switch, use suitable screws (not provided) to secure the brackets to the rack, as illustrat...
7 over-current of the switch, which is also a necessary measure to protect the body from electric shock. In different environments, the switch may be grounded differently. The following will instruct you to connect the switch to the ground in two ways, connecting to the grounding bar or connecting t...
8 figure 3-5 * the figure is to illustrate the application and principle. The power plug you get from the package and the socket in your situation will comply with the regulation in your country, so they may differ from the figure above. Note: if you intend to connect the switch to the ground via th...
9 appendix a: specifications general standards ieee802.3 10base-t ieee802.3u 100base-tx ieee802.3ab 1000base-t topology star protocol csma/cd data transfer rate ethernet: 10mbps (half duplex), 20mbps (full duplex) fast ethernet: 100mbps (half duplex), 200mbps (full duplex) gigabit ethernet: 2000mbps...
10 environmental and physical operating temperature 0℃~40℃ (32℉~104℉) storage temperature -40℃~70℃ (-40℉~158℉) operating humidity 10%~90% non-condensing storage humidity 5%~90% non-condensing.
11 appendix b: troubleshooting 1. The power led is not lit ¾ make sure the ac power cord connected the switch with power source properly. ¾ make sure the power source is on. 2. The link/act led is not lit when a device is connected to the corresponding port ¾ make sure that the cable connectors are ...
Smcgs1601/smcgs2401 7109504010