1. DL manuals
  2. SPRT
  3. Printer
  4. SP-POS88?
  5. User Manual

SPRT SP-POS88? User Manual

Manual is about: ?Thermal Receipt Printer

Summary of SP-POS88?

  • Page 1

    Sprt ® sp-pos88 Ⅴ Ⅴ Ⅴ Ⅴ thermal receipt printer user’s manual （ ver 1.00 ） beijing spirit technology development co.,ltd..

  • Page 2

    1 content introduction .......................................................................................... 2 chapter 1 feature and performance................................................... 2 1.1 print performance ..................................................................... 2 1.2...

  • Page 3

    2 introduction pos88 Ⅴ printer is a new type line thermal printer, it features in fast speed print, low print noise, high reliability, perfect print quality and ribbon needless, avoiding the vexation of regular maintenance. Pos88 Ⅴ printer: small in outline dimension, simple operation, and extensive...

  • Page 4

    3 1.2 print paper ● thermal paper roll model: tf50ks － e （ japan paper co.Ltd ） af50ks-e (jujo thermal) ● thermal paper roll: width －－－ 79.5±0.5mm outer diameter －－－ 80mm （ max. ） inner diameter －－－ 13mm （ min. ） thickness －－－ 0.06mm ～ 0.08mm 1.3 print font ● ank character set 12×24 dots ， 1.5 （ w ）...

  • Page 5

    4 ● cash drawer control dc24v ， 1a ， 6-pin rj-11 socket. 1.5 print control commands ● character print commands: support double-width, double height print of ank characters, user-defined characters and chinese characters, the character line spacing is adjustable. ● graphics print commands: support th...

  • Page 6

    5 sp-pos88 Ⅴ s rs － 232c serial interface sp-pos88 Ⅴ p parallel interface sp-pos88 Ⅴ e ethernet interface sp-pos88 Ⅴ u usb interface chapter 2 operation specification 2.1 printer appearance paper cover power indicator （ green ） status indicator(red ） paper-end indicator （ red ） paper feed button （ f...

  • Page 7

    6 cash drawer interface interface socket power socket fig.2-1 printer appearance 2.2 paper installation 2.2.1 paper loading pos88 Ⅴ adopts 79.5mm width thermal paper roll. Steps of loading thermal paper are as below: hold down the upper cover button on the left side, open the movable upper cover, dr...

  • Page 8

    7 it,and turn the white plastic gear by the direction suggestive on the cutter by hand to make the cutter be back to the original position. 2.3 interface 2.3.1 serial interface the serial interface of sp-pos88 Ⅴ printer is compatible with rs-232c, supports dtr/dsr and xon/xoff handshaking protocols,...

  • Page 9

    8 20 dtr output printer signal “mark” means the host is busy and can not receive data.Signal “space” means the host is ready to receive data. Fig. 2-3 the pin assignment of serial interface note: (1)“source” denotes the source that signal come from; (2)logical signal level is eia. The baud rate and ...

  • Page 10

    9 pin no. Signal direction description 1 strobe in strobe pulse to latch data, reading occurs at falling edge. 2 d1 in 3 d2 in 4 d3 in 5 d4 in 6 d5 in 7 d6 in 8 d7 in 9 d8 in these signals represent the 1st bit to 8th bit of the parallel data representatively, each signal is at high level when data ...

  • Page 11

    10 14,15,17 18,34,36 nc --- no connection 16,19~30, 33 gnd --- grounding logical 0 level 35 +5v --- +5v power fig.2-5 36pin assignment of parallel interface note: (1)“in” denotes input to the printer ， “out” denotes output from the printer. (2)signal level is ttl standard. The timing chart for inter...

  • Page 12

    11 pin no. Signal direction 1 chassis ground —— 2 cash drawer driver signal 1 out 3 cash drawer on/off status signal in 4 +24vdc —— 5 cash drawer driver signal 2 out 6 signal ground ——.

  • Page 13

    2.3.4 power connection pos88 Ⅴ uses the external power supply adopter as 24v±10 ％、 2a, power socket is a-1009-3p model,as fig. 2-10 shows: fig.2-8 power socket the pin assignment is as below ： pin no. Signal 1 +24vdc 2 ground 3 nc 2.4 buttons and indicators there is one button and three indicators o...

  • Page 14

    Jam. When any error shown above occurs,pin “nfault” of parallel change to “0” level,and send 1 bit wrong code through serial txd by itself,it can also send out the printer state by answer the esc v command. Red indicator of “paper out ” is the paper out indicatoe.When there is no paper in printer he...