SPX EF-7700 Manual

Page of 8

Download

Print this page

Bookmark us

MANUAL ENGLISH

Rev 1 date 26-04-11 RS 1-8

PRODUCT DESCRIPTION

IMPORTANT!

In order to get the best out of your system it is important you take

the time to read through the manual before you start to

install/program your equipment.

The system (EF-7700) consists out of two parts: the transmitter

(EF-7602) and the receiver including wiring (EF-7701).

The transmitter and receiver are preset and factory coded. This

means that the system is ready for use. Every transmitter has a

fixed, unique serial coding which has been programmed into the

receiver, so that another transmitter cannot control the receiver.

APPLICATIONS

The receivers and transmitters of the System EF-7700 are pre-

programmed. They are meant to control fixed or mobile equipment

with a limited amount of functions.

SAFETY

Ensure that:

Appropriate personnel receive a review of the systems’

functions before it is used.

Only appropriate personnel have access to the

transmitter.

The transmitter is not left unsupervised.

The operator always has a complete view of the

equipment when it is radio controlled.

Be sure that your hydraulic lift application is shut off

during transit.

CAUTION: tampering with the product, changing the settings

or using the product in a fashion other than as set forth

herein can lead to product malfunctions which in turn can

lead to serious injuries or death. Any tampering,

unauthorized change in the product, misuse or abuse will

invalidate SPX's warranty on the product.

1 2 3 4 5 6 7 Next › »

Summary of EF-7700

Page 1
Manual english rev 1 date 26-04-11 rs 1-8 product description important! In order to get the best out of your system it is important you take the time to read through the manual before you start to install/program your equipment. The system (ef-7700) consists out of two parts: the transmitter (ef-76...
Page 2
Manual english rev 1 date 26-04-11 rs 2-8 receiver ef-7701 operating voltage: 12-30 v ac/dc power consumption: 30-80 ma dimensions: 54 x 96 x 37 mm protection: ip 65 climatic conditions: -30°c to +70°c humidity: 10%-90% compatible transmitter: ef-7702 1. Yellow led lights up when the receiver has th...
Page 3
Manual english rev 1 date 26-04-11 rs 3-8 transmitter ef-7702 function the transmitter must be activated by pushing the on/off button for 3 seconds. After that the up or down button can be used for operating the system. The transmitter is active when the led glows steadily. Note: if the transmitter ...
Page 4
Manual english rev 1 date 26-04-11 rs 4-8 preparations assembly and installation 1. Select a suitable location for assembly of the receiver. 2. Connect the positive (+). (black 2) 3. Connect the ground cable of the receiver (yell/gr) 4. Connect the first coil (black 3) 4. The black cable (4) is to c...
Page 5
Manual english rev 1 date 26-04-11 rs 5-8 placement of the receiver - select a location, if possible, that is protected from the wind and weather. Place it with cable-glands facing downward. Avoid locations where the receiver may be exposed to abnormal moisture conditions, e.G. During high pressure ...
Page 6
Manual english rev 1 date 26-04-11 rs 6-8 2. Push the teach-in button on the receiver until the red led lights up. 3. Release the button when the red led light up. 4. Turn transmitter on. 5. Push on any button of the transmitter that is to be used with the receiver. The id-code will be programmed in...
Page 7
Manual english rev 1 date 26-04-11 rs 7-8 problem possible cause solution the yellow led of the receiver does not light up. The receiver is not well connected to the power supply. Incorrect power voltage supply. Check the connection of the power supply. Check the power voltage supply. The green led ...
Page 8
Manual english rev 1 date 26-04-11 rs 8-8 recycling, scrapping ef-7700-systems and any accessories and spare parts no longer in use should be scrapped and recycled according to local environmental regulations..