1 english (o rigina l in st ruct ions) instruction manual double insulation important: read before using. Router mrp090 011944.
2 english (original instructions) specifications model mrp090 collet chuck capacity 6 mm, 1/4" and/or 8 mm plunge capacity 0 - 35 mm no load speed (min -1 ) 27,000 overall height 218 mm net weight 2.7 kg safety class /ii • due to our continuing programme of research and development, the specificatio...
3 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for o...
4 3. Wear hearing protection during extended period of operation. 4. Handle the bits very carefully. 5. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 6. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operat...
5 caution: • since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 15 mm at a pass when cutting grooves with an 8 mm diameter bit. • when cutting grooves with a 20 mm diameter bit, the depth of cut should not be more t...
6 • do not tighten the collet nut without inserting a bit. It can lead to breakage of the collet cone. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. An 8 mm collet cone may be also provided as a standard equipment (depending on the country...
7 the side of the workpiece is not straight, the straight guide cannot be used. In this case, firmly clamp a straight board to the workpiece and use it as a guide against the router base. Feed the tool in the direction of the arrow. Dust nozzle set (for european countries only) 1 2 011953 use the du...
8 router bits straight bit 005116 mm d a l 1 l 2 6 1/4" 8 8 60 25 6 1/4" 6 1/4" 6 50 18 8 50 18 20 50 15 009802 "u"grooving bit r 005117 mm d a l 1 l 2 r 6 6 50 18 3 009803 "v"grooving bit 005118 90 mm d a l 1 l 2 1/4" 20 50 15 009804 drill point flush trimming bit 005120 d 8 6 a 6 8 l 1 60 60 l 2 1...
9 chamfering bit 005126 30 45 60 d 6 6 a 20 23 l 1 50 46 l 2 13 11 l 3 5 6 6 20 49 14 2 mm 009809 cove beading bit 005129 d 6 6 a 25 20 l 1 48 43 l 2 13 8 r 8 4 mm 009810 ball bearing flush trimming bit 005130 mm d a l 1 l 2 6 1/4" 10 50 20 009811 ball bearing corner rounding bit 005131 d 6 6 1/4" a...
10 ball bearing cove beading bit 005134 mm d a 1 a 2 a 4 l 1 l 2 l 3 r 6 6 5.5 3 5 10 12 5 26 22 8 42 20 18 8 a 3 12 12 40 009815 ball bearing roman ogee bit 005135 mm d a 1 a 2 l 1 l 2 l 3 r 1 r 2 6 6 2.5 4.5 3 4.5 4.5 6 26 8 42 12 20 8 40 10 009816.
11.
12 makita corporation anjo, aichi, japan www.Makita.Com 885033a939.
