Powersports audio kit phase 5 polaris ® genera l ® disassembly, wire and amplifier plate installation under dash subwoofer installation kick panel speakers installation cage mount speakers installation mrb3 and dash kit installation pg 2 pg 9 pg 17 pg 21 pg 25.
2.
3 gn-5k polaris general ssv works 5 speaker audio kit ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty against defe...
4 a panels and dash disassembly c e d f f a. Remove all seats by releasing the handle behind each seat, push forward slightly while lifting up. C. Remove hood by turning locking pins and lifting up. E. Remove top push pins as well as the lower t30 screw (this will allow for easy removal of top dash ...
5 h1 i1 h2 i2 h1. Using a panel removal tool, remove the two (2) push pins holding lower center panel cover located on the passenger side. Slide cover off. I1. Take out the rear center console pocket by using a panel removal tool and remove the two (2) push pins. I2. Once pins have been removed, pul...
6 j running amp power cable & speaker wire l p k o m j. Unplug the rubber grommet located on the firewall. L. Feed power/ground and h1150 harness down towards the center console until you get the wires to the inside of the vehicle. P. Feed each side of the h1149 harness down through the open cavity ...
7 q1 outside dash view inside dash view s u2 q2 u1 t q. Remove the two (2) t30 torx screws and clips located at the bottom of the dash panel near the center console l. Unclip harness that runs along top cross bar of dash (holes will be used to mount amp and sub plate). U. Once amp plate is laying fl...
8.
9 polaris general 10” under dash enclosure ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty against defects in mate...
10 a. For this step you will need the sub enclosure mounting plate as well as two (2) m5 screws, two (2) 8mm nuts and four (4) m5 washers. Place the mounting plate on the factory dash cross member bar behind the glovebox. Match up the holes from the plate and the bar to insert the m5 screws and wash...
11 j. Use three (3) m6 screws & washers to hand tighten the enclosure from behind the fi rewall. Once all m6 screws have been hand tightened, go back and tighten all screws with t30 torx driver. H. Place enclosure in location for mounting. K. Route the speaker wire away from any moving parts and sha...
12.
13 left side drill template 170-gn-ud10 drill template.
14.
15 right side- drill template 170-gn-ud10 drill template.
16.
17 polaris general 6.5” speaker front kick panels ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty against defects ...
18 c. Using a ¼ drill bit, drill holes for mounting of kick pods . E. Use the provided m6 screws and washers and loosely tighten the pod in place through the drilled holes. Once all screws have been loosely installed, tighten down by hand. F. Route the speaker wire away from any moving parts and any...
19.
20
21 polaris general 6.5” speaker cage mount pods ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty against defects in...
22 c f e a b c. Remove push clip on the rear panel to allow the running of the speaker harness up the driver and passenger cage bar to connect to the speakers. F. Using a t5 hex key tighten clamp until it secures to cage. E. Loosely install the clamp base to the cage mount pod with the two (2) 8 mm ...
23 j g h i j. Connect the b-h1151 speaker harness to the amplifier g. Tighten the 8mm bolts once you have the speaker pods in your desired location. H. Make your speaker connections. I. Using the provided zip ties tie down speaker wire alongside the roll cage..
24.
25 polaris general mrb3 dash panel ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty against defects in material or ...
26 c e g d f2 f1 c. Place the bottom edge of the kit on dash. E. Pull the mrb3 power and ground wires through the rubber grommet and feed through to the power strip located on the right side of the vehicle. G. Make the connection to mrb3 brain. D. With both thumbs press the top corners until the kit...
27 polaris general usb/aux input port a c e g b d a. Unscrew and remove the plastic nut from the port. Make sure to open the fuse holder and remove the fuse so the nut will fit through it. Crimp on the provided ring terminals on the ends of the (red) power and (black) ground wire. C. Feed in the wir...
28 connecting power & ground cable to battery this concludes the installation process. Replace all factory panels and seats. Questions? Please contact ssv works at 818-991-1778 or email support@ssvworks.Com © 2017 ssv works, oxnard, ca 93030 gn-5k rev. B 11-14-17 c b d c a d c. (if you have decided ...