- DL manuals
- SSV Works
- Automobile Accessories
- PHASE 5 US-C65K
- User Manual
SSV Works PHASE 5 US-C65K User Manual
Summary of PHASE 5 US-C65K
Page 1
Powersports audio kit phase 5 can-am ® ma verick x3 ® disassembly, wire and amplifier plate installation dash kit installation underseat subwoofer installation dash speaker pods installation cage mount speaker pods installation pg 3 pg 11 pg 15 pg 19 pg 23.
Page 2
2.
Page 3
3 x3-5k can-am maverick x3 & x3 max kicker 5 speaker audio kit ! Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle. Warranty information: all ssv works enclosures are covered by a limited lifetime warranty aga...
Page 4
4 a panels and dash disassembly b b b a c a. To remove the seat, use a 13mm socket and wrench to remove front (2) bolt and nut, and use a 18mm socket to remove (2) rear nuts and seat belt nut ( repeat on other seat) b. Carefully unsnap center dash side panels by hand or with a panel removal tool. C....
Page 5
5 panels and dash disassembly e e e e2. Using panel removal tool unsnap (2) push clips on the driver and passenger side dash covers. Unscrew the (4) t30 screws on the passenger side, and (7) t30 screws on the driver side. E. Remove gas cover on the passenger side to expose a 10mm nut. Unscrew with a...
Page 6
6 running amp power cable and speaker wire i1 i2 i. In this step you will be feeding all of the necessary wires from the top drivers side dash down the center dash column. Be sure to run all of the wires along side the factory cabling to avoid any moving parts. Feed both amp power wires, rear speake...
Page 7
7 installation notes amp tray modification with use with an aftermarket roll cage 1. Remove this threaded stud before installaion of the amp tray. Gently tap out the threaded stud with a hammer. Be careful not to bend the bracket. 2. If needed, increase the diameter of the hole to accommodate the ro...
Page 8
8 amp plate installation l n o k m k. From underneath driver side place amp plate between the two cross bars behind the steering wheel. L. Make sure the threaded bolt on the amp plate goes through the factory hole located in the corner where the cage tubing connects. * if your vehicle is equipped wi...
Page 9
9 amp plate installation p1 p2 q. Connect the b-h1149 to the front output of the 300.4 amplifer. Connect the b-h1151 to the rear output of the 300.4 amplifier. Connect the b-h1152 to the output of the 500.1 amplifier (q1). Connect the b-h1221 mrb3 power harness to the mrb3 brain (q2). Connect both a...
Page 10
10 usb/aux input port installation s s. Remove the (4) t30 torx on the front and inside of the glove box t. Remove push clips from underneath glove box. T u u. Pull up and remove the glove box. V v. Drill a 1” hole through the left side of the glove box for wiring w w w. Unscrew and remove the plast...
Page 12
12 a d c c c b e a. Remove the factory rocker switches. D. Place the base plate back on the dash lining up the outside screw holes to the dimples on the dash. Using (2) #7 screws and a philips screw driver secure the base to the dash. Make sure the screws are driving into the dash dimples for best r...
Page 13
13 f g h f g f. Now that the mrb3 remote is mounted to the dash kit route the din cable through the base plate so that it drops into the dash. Pull the din cable all the way through until the x3-dm3 top panel rests on the base plate. G. Using (2) #7 screws, secure the top of the top panel to the bas...
Page 14
14.
Page 16
16 a. Apply the foam strips to the inside right, left and top side of the enclosure. C. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long m6x25mm screw through the top. Then attach the brake line, spacer, washer and nut. T hen ...
Page 17
17 f. Place b-bracket to the left side of the enclosure and slide the tab underneath the enclosure. (f1) line up the 2 screw holes and proceed to hand thread the m6 screws and washers. Use a t30 torx bit to tighten screws. Repeat for the right side. (f2) line up the top of bracket a and b with the h...
Page 18
18.
Page 20
20 c. Using a utility knife, cut off the (4) tabs fl ush to the panel d. Drill a hole using a 1/4” drill bit at the factory dimple marks (as shown above) on the outside dash panel around the speaker grille. B. Pry off the (4) clips on the base under the empty space for the speaker c1 c2 d2 d1 b a. Re...
Page 21
21 e. Place the acousic lens on top of the factory grille, line up the holes and insert the (2) top m6x1.0 (shorter) screws and washers. F. Place the speaker pod under the dash panel and line up the holes on the speaker pod with the (2) top screws and loosely mount the pod to the dash panel. H. Inst...
Page 22
22.
Page 24
24 a. Find the best orientation for the speaker on your bar and screw in the set screws in the opposite holes of where the clamp will install into. B. Loosely install the clamp base to the cage mount pod with the two (2) m6 hex head bolts and washers, place the cage mount pod in the desired mounting...
Page 25
25 wiring instructions pxa 300.4 d e e d. Take the b-h1150 rear speaker harness and plug into the b-h1151 rear extension harness. E. Route the rear speaker harness (b-h1150) along the factory wires in the engine compartment and pull up through the small space between the bed panel and cage tubing on...
Page 26
26 connecting power & ground cable to battery this concludes the installation process. Replace the factory panels and seats. Questions? Please contact ssv works at 818-991-1778 or email support@ssvworks.Com © 2017 ssv works, oxnard, ca 93030 x3-5a rev. B 10-25-17 a b a c b a. Unscrew the factory nut...