1. DL manuals
  2. SUZHOU PARSUN POWER MACHINE
  3. Engine
  4. F2.6BM
  5. Service Manual

SUZHOU PARSUN POWER MACHINE F2.6BM Service Manual

Summary of F2.6BM

  • Page 1

    Parsun outboard engine service manual f2.6bm suzhou parsun power machine co., ltd..

  • Page 2: Notice

    Notice this manual includes service instructions for f2.6 and has been prepared by parsun power primarily for use by the dealers when performing maintenance and repair to parsun outboard engines. Before performing maintenance, please read the manual carefully. When performing maintenance and repair ...

  • Page 3: Index

    Index general information· ·········································1 identification· ············································1 propeller selection· ····································1 emergency start· ·········································1 safety while working· ···························...

  • Page 4

    Recoil starter· ················································19 notice· ··················································19 explosive drawing· ·····································20 disassembling· ··········································22 start rope replacement· ·····························...

  • Page 5

    Crankcase· ···········································43 disassembling· ······································43 piston· ·············································44 cylinder bore· ·······································44 piston pin diameter· ··································44 piston ring· ···...

  • Page 6

    Water pump assembly· ··································62 explosive drawing· ······································62 disassembling and inspection· ·····························63 lower unit· ··············································64 explosive drawing· ·····································64 ...

  • Page 7

    General information identifecation the outboard motor serial number is marked on the label. The label can be found on the bracket left assembly or on the upper part of the bracket swivel. Record your outboard motor serial number in the spaces provided to assist you in ordering spare parts from your ...

  • Page 8

    Items far away. Don’t touch flywheel or other moving parts. When starting and operating, don’t touch ignition coil, spark plug cap or other electric parts. The procedure is as follows: 1. Remove the top cowling. 2. Remove the bolts fixing the fuel tank. 3. Lift the fuel tank and remove three bolts. ...

  • Page 9

    8. When the engine is cold , circumvolve the lever of carburetor in order to operate choke system. Return lever to home position after engine starts. 9. Insert the knot of the cable in the notch of flywheel rotor, and wind the cable around flywheel several rounds in clockwise direction. 10. Pull the...

  • Page 10

    Under normal conditions of use, there should be no hazards from the use of the lubricants mentioned in this manual, but safety is all-important, and by adopting good safety practices, any risk is minimized. A summary of the most important precautions is as follows: ○ 1 to protect the skin, the appli...

  • Page 11

    ○ 1 check the engine oil level check engine oil level from oil level checking hole. 1. High position mark 2. Low position mark ensure the oil level between the marks of upper and lower. If above upper level, drain engine oil; if below lower mark, add engine oil up to upper level. ○ 2 check the gear ...

  • Page 12

    Cooling water overflows at the cooling water checking hole. 1 1. Cooling water checking hole 7. Breaking-in running ○ 1 initial 1 hour: operate the engine at 2000 r/min or about a half throttle. ② the second hour: operate the engine at 3000 r/min or about 3/4 throttle. ③ the following 8 hours: opera...

  • Page 13

    Valve spring compressor housing bearing installer lower casing cover bearing installer oil seal installer tool housing oil seal installer space gage sleeve bearing with guard board installer tool lower casing bracket and sleeve bearing without guard board installer tool lower casing bracket and driv...

  • Page 14

    Explosive drawing and symbol explosive drawing 水泵内壳 remarks part no. Description m6x40 mm 8nm g g 10 9 8 7 6 5 4 3 2 1 水泵座 f2.6-03000008 10 g f4-03000013 f2.6-03000007 gb/t5783-2000 f2.6-03000016 f4-03000021 jaso f404 19-033 六角螺栓m6x40 泵壳固定板 水泵内壳o形圈 f2.6-03000015 外档板 叶轮组件 o形密封圈 定位销φ4x18 水泵座密封垫 f2.6-0...

  • Page 15

    Specifications outboard engine specifications item description item description overall length 645mm spark plug bpr7hs overall width 343mm exhaust system under water dimension overall height 1013mm power unit lubrication system splash lubrication weight 18.0kg fuel type unleaded regular gasoline max...

  • Page 16

    Maintenance information power unit item description item description intake 0.08~0.12mm cylinder head warp limit 0.1mm valve clearance (cold) exhaust 0.08~0.12mm bore 54.00~54.015mm intake 1.84~2.26mm wear limit 54.1mm face width exhaust 1.84~2.26mm taper limit 0.08mm intake 0.6~0.8mm cylinder out o...

  • Page 17

    Cont’d item description item description valve opening temperature 58~62ºc intake/exhaust height 26.139~26.239mm full-open temperature 70ºc round diameter 21.950~22.050mm journal diameter 14.966~14.984mm camshaft camshaft round limit 0.03mm thermostat valve lift 3mm ignition system item description ...

  • Page 18

    Cont’d part to be tightened part name thread size quantity torque 1st tightening 5 nm connecting rod 2nd tightening bolt m7 2 9 nm power unit oil splash gear unit bolt m6 1 13 nm 1st tightening 3 nm lower unit mounting 2nd tightening bolt m6 3 8 nm 1st tightening 6nm lower unit housing cover 2nd tig...

  • Page 19

    Periodic service maintenance time table initial maintenace general maintenance period items contents 10 hours （1 month） 50 hours （3 months） 100 hours （6 months） 200 hours （1 year） anode inspection/replacement ○ ○ spark plug cleaning/adjustment /replacement ○ ○ ○ grease points greasing ○ bolts and nu...

  • Page 20

    Power unit engine oil level 1. From oil level checking hole, check if engine oil level is between the following marks of the upper and lower. 1. Oil level plug 2. Oil rule 3. High position mark 4. Low position mark 2. If above the upper mark, drain the engine oil; if below lower mark, add engine oil...

  • Page 21

    3. Fill engine oil into the crankcase through oil filler hole. Engine oil quantity: 0.35l oil type: api se, sf, se-sf, sg-cd sae 10w30, 10w40 4. Install oil level plug. 5. Check engine oil level. Valve clearance caution: rotate the flywheel clockwise so that rocker arm is in free position, before ad...

  • Page 22

    Control system throttle grip 1. Turn the throttle grip to fully closed position. 2. Check if the throttle cable is slack and if the throttle lever touches the throttle stop screw. 3. Loosen throttle cable stopper screw, adjust throttle cable position, and tighten throttle cable stop screw. 1.Throttl...

  • Page 23

    Lower unit gear oil check gear oil level: remove the oil level plug. If the gear oil overflows at the oil level checking hole, the oil volume added is correct; otherwise please add gear oil. 1. Oil level plug 1.Oil level plug changing gear oil 1. Hold the outboard engine in an upright position. 2. P...

  • Page 24

    Connecting the leakage tester to the oil level checking hole to check the lower unit leakage. If the pressure drops (pressure: 1kg/cm³), inspect the oil seal and components. General inspection anode inspect lower unit anode and engine anode (on the thermostat cover). Clean the greasy dirt and scales...

  • Page 25

    1 cooling water passage inlet 2. Place the outboard engine in the water and ensure the water level is above the anti-vortex plate, then start the engine. 3. Check if water overflows at the cooling water checking hole. If there is no flow or intermittent flow, check the cooling water passage. 1. Cool...

  • Page 26

    Explosive drawing 10 9 8 7 6 5 4 3 2 1 part no. Description remarks 13 8 1 2 4 5 6 15 12 12 11 10 7 9 3 16 17 14 18 g 0 f2.6-04070002 发泡密封条 f4-04130005 f2.6-04070003 f2.6-04070007 f4-04130100 f2.6-04070008 f2.6-04070001 f2.6-04070100 gb/t97.1-85 gb/t5782-2000 涡形弹簧 起动轮减磨片 锦纶编织线Φ3 起动手柄组件 手柄减震圈 发泡密封圈 起...

  • Page 27

    Remarks description part no. 18 17 16 15 14 13 12 11 f2.6-04070004 起动轮 1 2 起动器垫管b f2.6-04000025 f2.6-04000034 2 油箱减震圈b 起动器垫管a f2.6-04000024 3 起动压板螺钉 f4-04130008 1 f2.6-04070006 起动压板 1 起动压板夹簧 1 f4-04130007 f2.6-04070005 卡瓣 2 drull,sheave pawl,drive screw,starter bolt,starter plate,press bush ,starter...

  • Page 28

    Disassembling 1. Open the top cowling 2. Remove bolts fixing the fuel tank. 3. Remove the fuel tank and take down three bolts. 4. Lift the starter and remove choke cable from carburetor. 5. Remove the starter. Starter rope replacement 1. Pull the starter rope out, and insert it in the notch of the s...

  • Page 29

    2. Pull the starter rope completely. 3. Remove the starter handle cover from the starter handle, and remove the starter rope. Untie the knot at the end of the starter rope. 4. Pull out the starter rope completely. 5. Insert the new starter rope into the starter assembly, and fix the rope onto the sh...

  • Page 30

    Assembling reverse the steps of disassembling. Installation 1. Put starter onto the power unit. 2. Screw the hexagon bolt, and tighten it according to the specified torque. Specified torque: 8 nm ignition system notice when checking and repairing the ignition system, keep your hand, clothes, hair or...

  • Page 31

    M6x25 mm 8nm o m6x12 mm 8nm 44nm description part no. Remarks 3 2 1 1 1 1 1 1 gb/t5783-2000 f2.6-04000600 gb/t97.1-85 gb/t5783-2000 f4-04000021 f2.6-04000016 f4-04000019 f2.6-04000400 1 79 8 6 7 4 5 3 2 1 gb/t6171-86 wiring diagram 25.

  • Page 32

    5 w b b w ○ 1 flywheel ○ 2 ignition coil ○ 3 engine stop switch ○ 4 grounding ○ 5 spark plug wire beam color: w white b black spark plug ignition 1. Remove spark plug cap from spark plug. . 2. Connect the ignition tester to the spark plug cap. 3. Start the engine, and observe the sparks through the ...

  • Page 33

    Spark plug cap 1. Remove the spark plug. Check if the spark plug cap is broken. Replace if necessary. 2. Install the spark plug cap turn it clockwise until it is tight. Flywheel maintenance 1. Use flywheel holder to remove the nut and starter pulley; use flywheel puller to remove flywheel. 2. Check ...

  • Page 34

    Fuel system notice gasoline is inflammable and highly volatile liquid. Its leakage can cause fire and explosion. Don’t start the engine before all joints of the fuel system are connected or installed. When completing all maintenance steps, force short-time pressure to the fuel system to check for le...

  • Page 35

    Explosive drawing remarks part no. Description f2.6-04000028 f2.6-04000027 f2.6-04000026 f4-04120005 f2.6-04000033 f4-04120100 f4-04120105 f4-04120106 f4-04120104 f4-04120103 29.

  • Page 36

    Remarks part no. Description f4-04000032 f4-05000010 f2.6-04000030 f2.6-04000029 f2.6-04000017 jasof404 24-014 f2.6-00000004 gb/t823-2000 f2.6-04000022 f2.6-04000023 30

  • Page 37

    M6x75 mm 8nm remarks part no. Description 14 6 7 13 12 11 8 9 10 1 4 3 2 1 2 2 f2.6-04000010 f2.6-04000011 f2.6-04000018 f2.6-04070200 jaso f404 24-021 f2.6-04000300 f2.6-04000015 f2.6-04000012 gb/t97.1-85 gb/t5782-2000 1 6 2 3 4 5 7 8 9 10 1 1 1 1 1 1 2 5 11 1 1 14 13 1 1 12 f2.6-04000200 f2.6-0400...

  • Page 38

    Fuel tank removal and inspection 1. Open the top cowling. 2. Remove two bolts fixing the fuel tank. 3. Pull the fuel tank out. 4. Remove the fuel pipe from fuel tank. 5. Inspect if the fuel tank and fuel tank cover for crack, leakage or damage. Replace if necessary. 6. Inspect the tank strainer for ...

  • Page 39

    Power unit notice to avoid accidental start of outboard engine during maintenance, please take enough safety measures to cut the ignition system. For instance, remove engine stop lanyard from engine stop switch assembly, and remove spark plug cap from spark plug. Explosive drawing 33.

  • Page 40

    Description part no. Remarks m6x16 mm 1st 5nm 2nd 12nm 1 2 3 4 5 6 7 8 9 10 11 11 13 14 15 14 16 17 18 19 2 12 m6x20 mm 8nm 25nm m8x60 mm 1st 14nm 2nd 30nm gb/t5783-2000 pin f15-00000013 spile water assy f15-04000005 定位销φ4x12 水嘴组件（φ7/φ6） 六角螺栓 m6x20 气缸头组件 f2.6-04040100 气门导管 166f-010104 缸头罩密封垫 f2.6-04...

  • Page 41

    Remarks part no. Description m8x60 mm 1st 14nm 2nd 30nm 25nm m6x20 mm 8nm 12 2 19 18 17 16 14 15 14 13 11 11 10 9 8 7 6 5 4 3 2 1 m6x16 mm 1st 5nm 2nd 12nm 1 f2.6-04000001 f2.6-04000006 1 6 gb/t5783-2000 缸头罩 六角螺栓m6x16 缸头复合垫 气缸头螺栓b f4-04000034 4 火花塞 bpr7hs 1 cover，cylinder head bolt bolt spark plug g...

  • Page 42

    O o l 1277 1277 l o o 10nm remarks part no. Description f2.6-04000100 166f-000001 f2.6-04000002 f2.6-04040001 166f-010003 166f-010001 166f-010002 f4-04080008 f4-04080010 166f-010006 116f-010008 166f-010009 166f-010010 166f-010011 锁紧螺母 摇臂螺杆 凸轮减压组件 气门挺柱 气门推杆 导向板 排气门 进气门 进气门油封 气门弹簧 气门弹簧座 气门锁片 摇臂 摇臂球座 9...

  • Page 43

    1 2 3 4 5 6 7 8 9 10 part no. Description m8x20mm 18nm m8x14mm 20nm 9 7 9 10 9 6 7 8 9 10 1 2 5 4 3 11 12 13 14 15 16 17 17 18 20 21 22 19 23 24 25 25 o o o m6x45mm 1st 5nm 2nd 11nm l 1277 o m6x12mm 13nm 11 12 13 14 t15-04010202 f2.6-04050100 gb/t5783-2000 62/22c3 f2.6-04000004 jaso f404 31-025 f15-...

  • Page 44

    15 m8x20mm 18nm m8x14mm 20nm 9 7 9 10 9 6 7 8 9 10 1 2 5 4 3 11 12 13 14 15 16 17 17 18 20 21 22 19 23 24 25 25 description part no. Remarks o o o m6x45mm 1st 5nm 2nd 11nm l 1277 o m6x12mm 13nm 25 24 23 22 21 20 19 17 18 16 f15-00000013 gb/t5782-2000 gb/t5783-2000 f4-04000006 f4-04000001 f2.6-040600...

  • Page 45

    Description part no. Remarks m6x29mm 1st 5nm 2nd 9nm 1 2 3 4 4 5 6 10 9 8 7 f2.6-04020002 活塞气环1 piston ring 1 washer,plate 箱盖减磨片 f2.6-04000003 f2.6-04030000 crank assy 曲轴组件 连杆螺栓m6x30 bolt f2.6-04020103 rod，connecting 连杆组件 f2.6-04020100 活塞 f2.6-04020001 piston 活塞销 f2.6-04020005 pin,piston circlip 活塞销...

  • Page 46

    Special tools piston slider bearing puller valve spring compressor housing bearing installer oil seal installer tool housing oil seal installer space gauge disassembling power unit from outboard engine 1．open the top cowling. 2．remove fuel tank; remove starter. 3．remove flywheel cover and throttle c...

  • Page 47

    4. Remove the rocker arm pivot, rocker arm, rocker arm shaft and push rod plate. 5. Use the valve spring compressor to remove intake door and exhaust door. Push rod inspect valve push rod runout. Replace if exceeding the specified value. Valve push rod runout limit: 0.5mm valve and valve pipe 1. Ins...

  • Page 48

    Valve rocker arm check the rocker arm for crack, perforation or damage. Replace if necessary. Valve pipe replacement 1. Knock out the valve pipe from the direction of combustion room. 2. Knock in the new valve pipe from the direction of the top of cylinder cover. Note: coat the oil on the surface of...

  • Page 49

    4. If the valve seal surface is too narrow and on the bottom edge of valve surface, use 60°cutter to adjust the bottom edge of the seat, and use 45°cutter to adjust the valve seat width if necessary. 5. Coat evenly a thin layer of lapping compound onto valve seat, and lap the valve by lapping tool. ...

  • Page 50

    6. Remove crankcase and crankcase gasket. 7. Remove oil splasher gear assembly. 8. Remove oil seal shell bolts, and remove oil seal shell and oil seal. Piston measure piston outside diameter at the specified measuring point. If out of specification, replace. Piston diameter: 53.950～53.965mm measurin...

  • Page 51

    1. Inspect camshaft decompressor, gear, and weight. If gear is worn/damaged/cracked, replace. If weight is unsmoothly moving, replace. 2. Measure camshaft lobe diameter○ a and height ○ b . If out of specification, replace it. ○ a camshaft: 21.950～22.050mm b a ○ b camshaft: 26.136～26.239mm 3. Measure...

  • Page 52

    Valve lifter 1. Inspect valve lifter for wear or damage. Replace if necessary. 2. Measure valve lifter outside diameter. If out of specification, replace the valve lifter. Valve lifter outside diameter: 7.9650mm oil splash gear inspect oil splash gear unit, if slow-moving/wear/damage/crack, replace....

  • Page 53

    Piston installation use piston slider to install piston, and make sure the piston crown “up” is toward the flywheel side. Note: apply motor oil to the piston and piston ring side when installing. Oil seal housing installation. 1. Install oil seals 10.8x21x7 (2 pieces) by oil seal installer tool. 2. ...

  • Page 54

    Apply motor oil to moving parts before installing. Crankcase cover installation 1. Install oil seal housing. 2. Install oil splasher gear assembly. 3. Install crankcase cover, and tighten the bolts twice as shown. Tightening torque: 1st 5 nm 2nd 11 nm note: apply motor oil to moving parts before ins...

  • Page 55

    Remarks part no. Description gb/t845-85 f2.6-06000003 f2.6-06000002 f2.6-06000001 disassembling and inspection 1. Remove intake silencer bolt. 2. Remove intake silencer and intake silencer damper.. 3. Inspect if top cowling, intake silencer and intake silencer damper are cracked or damaged. Replace ...

  • Page 56

    Bottom cowling explosive drawing part no. Description f2.6-05000002 金属连接杆 放油口胶套 底罩密封条 gb/t96-85 f2.6-05000005 f2.6-05000009 gb/t845-85 f2.6-05000001 f2.6-05000003 f2.6-05000007 f2.6-05000006 gb/t5783-2000 f2.6-05000010 f2.6-05000008 f2.6-05000004 平垫圈6 锁紧钩连接件 底罩 长方形橡胶闷头 凸缘垫管 底罩减震圈 六角螺栓m6x25 顶罩锁紧钩 圆形闷...

  • Page 57

    4. Inspect if bottom cowling is cracked or damaged. Replace if necessary. 5. Inspect if top cowling locking hook is cracked or damaged. Replace if necessary. Steering handle explosive drawing 9 10 8 7 1 2 3 4 5 6 m8x25mm 18nm l 1243 g g g remarks part no. Description bolt ,friction adjusting bush a,...

  • Page 58

    G description part no. Remarks g g g 1243 l m8x25mm 18nm 21 22 23 24 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 25 1 1 26 27 f4-01090001 操舵手柄 f4-01090002 gb/t818-85 十字槽盘头螺钉m5x12 节气门杆固定板 节气门杆组件 操舵手柄握把摩擦块 f4-01090003 f4-01090100 f2.6-02010003 衬套 油门标志牌 gb/t848-85 f4-01090007 压缩弹簧 小垫圈10 gb/t827-86 t15-01020302 操舵手柄橡...

  • Page 59

    4． remove friction adjusting bolt. 5． remove steering handle. 6． remove throttle cable. 7． remove throttle lever stay and throttle lever. 8． remove engine stop switch. 9． inspect if steering handle is cracked or damaged. Replace if necessary. 10． inspect if bush, bush washer and wave washer are crac...

  • Page 60

    M6x30 mm 12nm remarks part no. Description 1 2 3 4 5 6 7 8 9 10 washer locked handle assy bushing b bushing a locked block assy locked screw f2.6-01050100 锁紧手柄组件 cover，bracket cover，swivel bracket 1 damper 承推减震器 f2.6-01040100 1 1 1 旋转支架衬套b 旋转支架衬套a f2.6-01000004 f2.6-01000003 f2.6-01050200 1 锁紧块组件 4 ...

  • Page 61

    G g 16 nm 5 nm 5 nm g description part no. M6x30 mm 12nm 15 28 27 26 25 24 23 22 21 20 19 18 17 16 f2.6-01040001 f2.6-01000001 承推托架 f2.6-01030007 起翘块 f2.6-01030100 f4-01090006 衬套 角度锁紧手柄组件 gb/t879.2-2000 f2.6-01030004 f2.6-01030003 角度锁紧手柄钮簧 角度定位件 gb/t7940.1-95 直通式压注油杯m6 旋转支架座 f2.6-01030001 f2.6-01030...

  • Page 62

    G 5 nm 5 nm 16 nm g g m6x30 mm 12nm remarks part no. Description 29 1 1 1 1 1 1 1 1 2 2 2 2 1 1 2 43 42 41 40 39 38 37 36 35 34 33 32 31 30 gb/t6170-85 f2.6-01010001 f2.6-00000102 f2.6-01040000 f2.6-00000100 f4-01010005 gb/t5782-2000 f2.6-01000002 f4-01010003 f4-01010004 f4-01010002 f2.6-01020000 f2...

  • Page 63

    Disassembling and inspection 1. Remove clamp handle and bracket cover. 2. Remove swivel bracket cover. 3. Remove swivel bracket bushing and damper . 4. Remove clamp bracket 5. Remove swivel bracket. 6. Remove title clamp handle and title lock lever. 7. Inspect the the swivel bracket and clamp bracke...

  • Page 64

    Upper unit explosive drawing 9 10 8 7 6 5 4 3 2 1 remarks part no. Description 轻型直槽弹性圆柱销2.5x14 变档连杆支架 connector,shift rod b 变档连接器b f2.6-00000002 gb/t91-86 gb/t5783-2000 f2.6-02000008 gb/t97.1-85 f2.6-02020000 jisb2401 f4-02000002 gb/t5783-2000 gb/t879.2-2000 geae shift handle assy bolt bushing,shift...

  • Page 65

    21 20 19 18 17 16 15 m6x20mm 10nm m6x25 mm 5 nm g remarks part no. Description washer 1 大垫圈 f4-00000005 f4-02000003 ball 8 spring,gear 1 1 变档弹簧 钢珠8 gb308-84 护盖衬管 f2.6-02000001 bush 1 f2.6-00000102 grease cup gasket,exhaust cover upper casing f2.6-02000004 gb/t97.1-85 f15-0000013 f2.6-00000003 f2.6-0...

  • Page 66

    水上装置橡胶堵头 f4-02000012 gb/t818-2000 十字槽盘头螺钉m6x16 30 29 m6x20mm 10nm m6x25 mm 5 nm g remarks part no. Description disassembling and inspection 1. Remove the water tube. 2. Remove gear shift handle assembly. 60

  • Page 67

    3. Remove the shift rod and shift rod lever. 4. Remove exhaust cover. 5. Check upper casing for crack or wear. Replace if necessary. 6. Check gear shift handle for wear or damage. Replace if necessary. 7. Check exhaust cover for crack or wear. Replace if necessary. 61.

  • Page 68

    Lower unit water pump assembly explosive drawing 1 2 3 4 5 6 7 8 9 10 g g m6x40 mm 8nm description part no. Remarks 水泵内壳 泵壳橡胶管 f2.6-03000009 f2.6-03000010 f2.6-03000100 水泵座密封垫 定位销φ4x18 o形密封圈 叶轮组件 外档板 f2.6-03000015 水泵内壳o形圈 泵壳固定板 六角螺栓m6x40 jaso f404 19-033 f4-03000021 f2.6-03000016 gb/t5783-2000 f2.6-...

  • Page 69

    Disassembling and inspection 1. Remove water pump fixed plate. 2. Remove water pump housing. 3. R emove impeller, inner housing and o ring of water pump inner housing. 4. Remove water pump base. . 5. Check water pump housing and out plate for crack, crank or damage. Replace if necessary. 6. Check in...

  • Page 70

    Lower unit explosive drawing description part no. Remarks lower casing 水下装置壳体 drive shaft 驱动轴 叶轮定位销φ3.5x7 f2.6-03000013 f2.6-03000011 oil seal washer bolt 2 2 2 平垫圈6 六角螺栓m6x16 螺旋桨轴油封13x22x7 f4-03050002 gb/t97.1-85 gb/t5783-2000 f2.6-03000012 轴用钢丝档圈 1 1 1 pin clip oil seal bearing 1 1 1 驱动轴下油封9.8x24x...

  • Page 71

    F2.6-03000202 clutch block positive gear assy plug,shift ball bearing 正档齿轮组件 1 1 离合器块 f2.6-03000019 变档柱塞 深沟球轴承 1 1 ntn 6003 ey f2.6-03000020 水下装置壳体盖 f2.6-03000301 f2.6-030000201 f2.6-03000021 jisb 2401 p48 f2.6-03000002 螺旋桨轴 驱动轴垫圈 水下壳体盖o形圈φ47.1x3.5 1 1 1 1 1 1 带档边筒形轴承 shaft,propeller washer o-ring b...

  • Page 72

    1277 l m6x30 1st 3nm 2nd 8nm g m6x12mm 1st 3nm 2nd 8nm g 1277 l m6x16mm 8nm g description part no. Remarks 1 circlip gb/t896-86 f4-03000023 plug,oil hole gasket 注油孔螺塞垫 2 2 注油孔螺塞 f4-03000024 开口档圈6 13 12 6 5 4 24 20 21 22 23 1 3 2 1 3 1 六角螺栓m6x30 gb/t5783-2000 六角螺栓m6x12 gb/t5783-2000 f4-03000022 阳极 gb...

  • Page 73

    Disassembling and inspection 1．remove cotter pin, nut assy, and spacer. 2．remove propeller assembly and spacer. 3．remove the lower casing cover. 4．remove drive shaft, positive gear assy, and shift plug. 5．remove shift rod cam assy and drive shaft. 6．remove sleeve bearing with guard board. 7．remove s...

  • Page 74

    Lower casing cover oil seal and bearing installation install oil seal. Note: please use special tool to install oil seal and bearing. Pay attention to the oil seal installation direction and installation depth. Sleeve bearing inspect sleeve bearing with guard board and sleeve bearing without guard b...

  • Page 75

    Lower casing bracket and drive shaft oil seal installer tool 69.

  • Page 76

    Common troubles and solutions trouble type possible reason recovery action starter will not operate starter components are faulty repair or replace fuel tank is empty fuel is contaminated or stale fill tank with clean, fresh fuel air vent screw not loosened loosen air vent screw spark plug(s) fouled...

  • Page 77

    Cont’d trouble type possible reason recovery action fuel system is obstructed check for pinched or kinked fuel line or other obstructions in fuel system fuel is contaminated or stale fill tank with clean, fresh fuel spark plug gap is incorrect inspect and adjust as specified ignition wiring is damag...