1. DL manuals
  2. Suzohapp
  3. Cash Counter
  4. 10-18 Series
  5. Instruction And Service Manual

Suzohapp 10-18 Series Instruction And Service Manual

Summary of 10-18 Series

  • Page 1

    Intelligent cube hopper mkii rev 2.0 page 1 cube hopper ® mkii instruction - service manual intelligent cube hopper model 10-18xx-xx version 2.0 / apr 2013 a new design to solve most of your payout problems! Approved.

  • Page 2

    Intelligent cube hopper mkii rev 2.0 page 2 table of contents reference chart ............................................................................................................................. 3 instruction manual ..............................................................................

  • Page 3

    Intelligent cube hopper mkii rev 2.0 page 3 reference chart model no.10-18xx-10 diameter 15.40 to 17.55mm. Thickness 1.30 to 1.70mm. Disc is marked "1" (part no. 10-0240-1). Use coin insert plate 9 (part no. 10-0238-9) coin bridge no mark (part no. 10-0239). Model no.10-18xx-15 diameter 18.00 to 18....

  • Page 4

    Intelligent cube hopper mkii rev 2.0 page 4 payout discs mark on disc new old diameter* thickness* part no. 1 15.40 - 17.55 1.30 - 1.70 10-0240-1 2 a 18.00 - 22.09 1.50 - 2.09 10-0240-2 22 18.00 - 22.09 1.30 - 1.45 10-0240-22 3 aa 18.00 - 22.09 2.10 - 3.20 10-0240-3 4 b 22.10 - 25.59 1.50 - 2.09 10-...

  • Page 5

    Intelligent cube hopper mkii rev 2.0 page 5 congratulations on your purchase of this inteligent cube hopper mkii and thank you for having confidence in our suzohapp quality products instruction manual 1. Standard hopper for different applications the cube hopper is a single coin payout system made u...

  • Page 6

    Intelligent cube hopper mkii rev 2.0 page 6 h o pper rs 232 service manual 2. Electrical features 2.1. Connections pin 1 low level pin 2 low level (common). Pin 3 start input. Pin 4 mode input. Pin 5 busy / ready output pin 6 coin exit output pin 7 power supply (12 or 24vdc). Pin 8 signal common gro...

  • Page 7

    Intelligent cube hopper mkii rev 2.0 page 7 3. Interface signals table 1 lists all signals. Pin signal type description 1 high impedance (internal 100k pull up to 5v) connected to hopper low level signal plate 2 low impedance (internal 100 ohm to 0v) connected to hopper low level ground plate 3 opto...

  • Page 8

    Intelligent cube hopper mkii rev 2.0 page 8 3.8. Motor control connecting and interrupting the +12 or +24vdc supply controls the motor. The motor is automatically stopped when the power-supply is switched off. Motor duty cycle is 2:1. An electronic overload detection system protects the motor and in...

  • Page 9

    Intelligent cube hopper mkii rev 2.0 page 9 4. Hopper operation 4.1. Mode’s the hopper can be set in one of 3 different operating modes: 1. Continuous mode (jp1 shorted, jp2 shorted) 2. Logic mode (jp1 open, jp2 open) 3. Pulsed mode (jp1 open, jp2 shorted) these modes are described in the next chapt...

  • Page 10

    Intelligent cube hopper mkii rev 2.0 page 10 4.4. Continuous mode anti-jam operation if the hopper for some reason blocks (jams) the motor current will rise fast. When the current exceeds a certain trip level (around 1.6 amp), the motor will be reversed for t_clear ms. This is done to withdraw any c...

  • Page 11

    Intelligent cube hopper mkii rev 2.0 page 11 4.5. Logic mode the logic mode is activated if jp1 and jp2 are open. The power must be put off / on in order for the logic mode to be activated. 4.6. Logic mode normal operation in this mode, the hopper in started by setting the start level to a voltage b...

  • Page 12

    Intelligent cube hopper mkii rev 2.0 page 12 4.7. Logic mode anti-jam operation if the hopper for some reason blocks (jams) the motor current will rise fast. When the current exceeds a certain trip level (around 1.6 amp), the motor will be reversed for t_clear ms. This is done to withdraw any coins ...

  • Page 13

    Intelligent cube hopper mkii rev 2.0 page 13 4.8. Pulsed mode the pulsed mode is activated if jp1 is open and jp2 is shorted. The power must be put off / on in order for the pulsed mode to be activated. 4.9. Pulsed mode normal operation in this mode, for each active high or active low pulse on the s...

  • Page 14

    Intelligent cube hopper mkii rev 2.0 page 14 5. Mechanical features 5.1. Dimensions & weight dimensions: d: 125mm w: 125mm h: 152mm weight: 780 grams 5.2. Removing the motor and gearbox the motor is controlled by the pcb and operates the disc by means of gears and shafts. The gearbox is constructed ...

  • Page 15

    Intelligent cube hopper mkii rev 2.0 page 15 6. Maintenance important: shut-off power from the host machine before starting any cleaning activities. 6.1. Removing and re-installing the hopper the hopper can easily be removed by pressing on the yellow release button on the mounting plate and then rem...

  • Page 16: Technical Specifications

    Intelligent cube hopper mkii rev 2.0 page 16 8. Optional add-ons 8.1. Cup extension (part no. 10-0200) a 65mm high extension together with standard coin-cup increases the capacity of the cup from 300 to 500 coins of €2.00 (25.75mm in diameter, 2.2mm thick). It can be used with all coins with diamete...

  • Page 17

    Intelligent cube hopper mkii rev 2.0 page 17 design and specifications are subject to change without notice. Wijzigingen in ontwerp en technische gegevens voorbehouden, zonder kennisgeving. La conception et les spécifications sont modifiables sans préavis. El diseño y especificaciones están sujetos ...