Summary of C10
Page 1
1 c10 color display configuration manual p/n 99954-62016.
Page 2
2 all information, illustrations, photographs and specifications contained in this book are based on the latest product information available at the time of publication. Produced by suzuki motor of america, inc. Technical publications & training issue date: june 2016.
Page 3: Contents
3 contents introduction 4 single engine configuration 4 initial power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 select a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 set the time and date . . . . . . . . . . . . . . . . . . . . . . . . . ....
Page 4: Single Engine Configuration
4 single engine configuration this section shows you how to configure a single engine configuration using one (1) c10 color display kit, a fluid level sensor and a gps. This is a typical configuration for a single-engine configuration. You may choose to configure your vessel differently, and add or ...
Page 5
5 set the time and date note: with a gps installed, the local time offset is automatically populated. 1. To set the time and date manually, use the arrow buttons to select time format, then use the arrow buttons to select the 12-hour or 24-hour time format and press enter. 2. Use the arrow buttons t...
Page 6
6 3. After setting the time and date, confirm the information is correct, then select next and press enter. Select the units to be displayed on the units screen, use the arrow buttons to select how you want the units to be displayed on the c10, then press enter. Vessel set-up 1. On the vessel set-up...
Page 7
7 2. Use the arrow buttons to set the fuel capacity and press enter. 3. After confirming the vessel setup information, select ok and press enter. Engine display set-up on the engine display setup screen, the c10 defaults center in the engine 1 box. If you are only setting up the c10 for a single eng...
Page 8
8 configure devices on the network 1. To configure devices on the vessel’s network, press the menu button once. 2. Press enter to select settings. 3. Use the arrow buttons to select system and press enter..
Page 9
9 4. Select network and press enter. 5. Select device list and press enter. 6. The device list screen that opens is used to access and configure each device connected to the network. Tip: you can use this screen to confirm that your devices are properly connected to the network. For example: 6.1 sel...
Page 10
10 6.2 select data and press enter. 6.3 check for live data for that device. If you see live data, this confirms that the device is both connected properly and is transmitting data to the c10. Using the auto select function 1. To add a device, press menu once so that the c10 returns to the system sc...
Page 11
11 4. A message advises you that this screen re-selects and removes any invalid data source selections, to make sure that all network devices are connected and turned on . Then select yes and press enter. Note: it may take up to 30 seconds for the auto configure process to complete. 5. The screen re...
Page 12
12 configuring the fluid level sensor 1. Use the arrow buttons to select fluid level sensor. 2. There are three selections within the fluid level sensor screen: – configure – alarms – calibrate 3. Select configure and press enter. Note: when configuring a single fuel tank, the fluid level sensor wil...
Page 13
13 4. Use the down arrow to select fluid type, then press enter. 5. Select yes to confirm it. 6. Use the arrow buttons to specify tank size..
Page 14
14 7. Select yes to confirm it. 8. Press menu to return to the previous screen. Setting the alarm 1. Use the arrow buttons to select alarms, then press enter. 2. The default setting for alarms is zero, but it is recommended that a low fuel alarm be set. In this example, it is being set for 20 percen...
Page 15
15 3. Use the arrow buttons to adjust the alarm percentage (for example, 20 percent). Then select set configuration and press enter. 4. A warning screen asks you confirm that you want to change the fluid level configuration — select yes and press enter. 5. Press the menu button to return to the flui...
Page 16
16 2. The next screen provides you with five steps for calibrating the fluid level sensor: 2.1 select the number of calibration points. 2.2 select the tank level to calibrate. 2.3 fill the tank to the selected tank level. 2.4 press calibrate. 2.5 repeat the procedure above for each tank level. 3. To...
Page 17
17 5. When the calibration/point set screen opens, ok is highlighted — press enter again. 6. When the fluid level - calibration screen re-opens, select full from the fluid level drop- down, then select calibrate and press enter. 7. When the calibration/point set screen opens, ok is highlighted — pre...
Page 18
18 gps antenna the next item on the device list is the gps anten- na. If the gps is properly connected, it does not need to be configured. Suzuki engine interface 1. The last item on the device list is the suzuki engine interface. There is no need to configure the engine interface for a single-engin...
Page 19
19 2. From the default screen, press menu and press enter. Then select settings and press enter. 3. On the settings screen, select pages, then press enter. 4. Select pages again and press enter..
Page 20
20 5. Select box number 4 and press enter. Note: the boxes for the first three items in the pages screen are checked — these are default pages that are already configured and cannot be changed. 6. Select replace and press enter — this allows you to choose from ten custom page templates. Note: choosi...
Page 21
21 8. After pressing enter, the pages screen shows a check mark and a description for the page you have just selected for item number 4 on the list. 9. Press menu to return to the default screen. 10. Use the arrow buttons to locate the custom page that you just added. 11. Press the menu button — you...
Page 22
22 12. The box is highlighted in the new screen that appears — this is where you can change the data field. 13. Press enter — the data options are now listed for you. Note: with 10 different categories shown, there are also 43 different options within those 10 categories. These are all nema 2000 opt...
Page 23
23 15. Select fuel remaining and press enter. This provides you with the data from the fluid level sensor. 16. After selecting the data, the screen highlights the frame of the c10 color display. 17. Press the menu button and select save, then press enter..
Page 24
24 18. After adding the custom page, the data is saved and the operator can scroll through the three default pages and the custom page that has been added. For example, the fuel remaining screen. You have now finished configuring the c10 for the typical single-engine vessel application. This include...