1. DL manuals
  2. Suzuki
  3. Motorcycle
  4. k8 gsx1300r
  5. Service Bulletin

Suzuki k8 gsx1300r Service Bulletin

Manual is about: 4 - stroke

Summary of k8 gsx1300r

  • Page 1

    Hayabusa-zone.Com bikeland.Org - 1/12- motorcycle / atv division 4 - stroke gs/gsx/gsx-r bulletin no. 183 date: 6/6/2008 subject: recall campaign - ignition switch inspection/ replacement affected units: certain 2008 gsx1300rk8 motorcycles reference: gsx1300r service manual (pn 99500-39350-03e) atta...

  • Page 2

    Hayabusa-zone.Com bikeland.Org - 2/12- affected unit vin ranges: the vin ranges of the affected gsx1300rk8 models are listed below.Confirmation of an affected unit can be checked on suzuki connect. Note: if your dealership has sold an affected gsx1300rk8 to a customer, but you have not yet submitted...

  • Page 3

    Hayabusa-zone.Com bikeland.Org - 3/12- customer notification: in the safety recall campaign letter that will be mailed on june 10, 2008 (see attachment), customers are being advised to contact the suzuki dealer where they purchased their affected unit to schedule an appointment to have the ignition ...

  • Page 4

    Hayabusa-zone.Com bikeland.Org - 4/12- inspect routing 1. Remove the upper and lower meter panels (refer to service manual page 9d-15). 2. Check if the ignition switch lead wire is clamped and routed correctly. Incorrect positions are shown in figures 1 and 2. Correct routing and clamping is shown i...

  • Page 5

    Hayabusa-zone.Com bikeland.Org - 5/12- figure 3 correct correct correct figure 4 rerouting 1. Reroute the ignition switch lead wire correctly (figure 3 and figure 4). The ignition switch lead wire should not be covered by the other wire harnesses. 2. Turn the handlebars back and forth to verify that...

  • Page 6

    Hayabusa-zone.Com bikeland.Org - 6/12- remove the ignition switch assembly from the motorcycle (refer to service manual page 1h-12). Remove the two black plastic covers to access the cylinder cap mounting bolts (figure 5). Note: the black plastic covers will not be reused. Secure the mount area (bot...

  • Page 7

    Hayabusa-zone.Com bikeland.Org - 7/12- 5. 6. 7. Remove the shutter. The shutter may come off the ignition switch in the cylin- der cap, but is not secured to the cap. Remove the rotor and spring from the ignition switch. When the rotor is re- moved, the spring may be attached to the rotor, but it wi...

  • Page 8

    Hayabusa-zone.Com bikeland.Org - 8/12- figure 14 projections hollows figure 13 place the shutter from the original igni- tion switch on the rotor, aligning and placing the projections into the hollows (figure 13). The shutter can be aligned one of two ways 180 o apart. Either way is correct. Place t...

  • Page 9

    Hayabusa-zone.Com bikeland.Org - 9/12- warranty reimbursement & claim information: submit a warranty claim for each recall campaign service immediately upon completion of the repair. This campaign requires you to file a warranty claim using the following information. Short form claim: use the short ...

  • Page 10

    Hayabusa-zone.Com bikeland.Org - 10/12- customer satisfaction: we understand and apologize for any inconvenience this recall campaign may cause you or your customers. Thank you for your cooperation in conducting this very important campaign for your customers' safety and satisfaction. Only your cons...

  • Page 11: Safety Recall Campaign #2A05

    Hayabusa-zone.Com bikeland.Org - 11/12- customer notification letter - page one of two june 10, 2008 safety recall campaign #2a05 certain 2008 gsx1300rk8 (hayabusa) motorcycles ignition switch inspection/replacement dear suzuki owner: this notice is sent to you in accordance with the requirements of...

  • Page 12

    Hayabusa-zone.Com bikeland.Org - 12/12- customer notification letter - page two of two how do i receive the fastest possible service (cont.) when you pick up your repaired motorcycle, please allow a few extra minutes for your dealer to prepare and complete the necessary warranty paperwork with you. ...