Service manual suzuki musical inst.Mfg.Co.,ltd. 2-25-12, ryoke, nakaku, hamamatsu, japan dec.2008 hammond 44 pro-44h.
1 2-1,2-2 3-1~3-3 4 5 6-1~6-4 1.Specifications 2.Inspection spcification 3.Disassembly procedure 4.Wiring connection 5.Schematics vrs-38a 6.Parts list -1- pro-44h -table of contents- 1.Specifications keyboard reeds reed plates 1/4 inch output jack microphone control dimensions weight accessories c~g...
2.Inspection specification 0. Required equipment 0-1 mixer and headphone (you need a equipment which you can listen to the microphone sound with a headphone) or amplifier (which produces the bigger sound than live sound, and also the microphone level is available) 1. Sound inspection 1-1 insert a mo...
5. Blowing inspection 5-1 check the lowest ceg chord in low volume and see if there is any fluttering sound. Check other chord dfa, egb … to bdf in the same way. In case you find a wrong key, check again after blowing strongly without sound. 5-2 check if overtone sounds equally overall. 5-3 play aro...
Pro-44h unscrew 6 cover screws.(screw : m3x8, ni) 1.Remove the cover ass'y : 2.Remove the air box: 3-1 3.Disassembling procedure unscrew 5 air box screws.(screw : m3x15, bsni) press the spit-valve and hold open. Pull out the air box upward. 3.Disassemble each read plate unscrew reed plate screws.(sc...
Unscrew this screw (small, truss screw, m3x16) and remove a washer and strap pin. 4.Remove treble side cover unscrew 3 screws (tapping screw, round, 2.3x6.5, bsni). Remove a jack volume assy's connector. To prevent the cable cut off, please hold the connector's base. 3-2 pro-44h 5.Remove the dynamic...
4.Wiring connection pro-44h -4- (jack volume ass'y) s olde r t o v rs - 38 la nd re d : s b la c k : g g re e n : f g (m a rk is on t h e s ilk s ide ) f g g s v r s- 3 8 a a s s 'y e 0 1 c o 1 - 1 m j-159m roh s s olde r t o m j- 159m re d c a b le : c h ip s ide b la c k c a b le : rin g s ide ju ...
6.Parts list 6-1 pro-44h 1.Fainal ass'y(10051-01101) 10051-02101 00290-00039 00290-00040 00290-00041 00290-00042 10051-02102 middle plate ass'y high plate ass'y top high plate ass'y air box ass'y keyboard ass'y bass plate ass'y 2 1 3 4 5 6 10051-02103 bass side cover ass'y 7 10051-02104 treble side ...
6-2 2.Keyboard ass'y(10051-02101) pro-44h 00452-00017 00290-00014 00452-00031 00453-00059 00453-00061 00453-00062 air lid 1 keyboard cushion rear rim valve packing body keyboard set 14 2 1 3 4 5 6 11 a a 000001 00451-00100 00451-00150 01724-63000 00453-00049 00412-13018 square nut(trivalent white) k...
6-3 pro-44h 00452-00110 00453-00063 00452-00032 air lid 2 air box air box packing c 2 1 3 00451-00172 cup 4 00453-00070 rubber rubber 1 5 00453-00057 rubber rubber 2 6 3.Air box ass'y(10051-02102) 4.Bass side cover ass'y(10051-02103) 00452-00086 00453-40116 01724-63000 square nut(m3, trivalent white...
6-4 pro-44h 1 1 6.Flexible mouthpiece ass'y(00290-00084) 7.Mouthpiece with tube and l-shaped joint(00290-00092) 00453-00032 o-ring 1 00453-00032 o-ring 1 00290-00092 00290-00084 00290-00083 short mouthpiece mouthpiece with tube and l-shaped joint flexible mouthpiece 2 1 3 00453-00072 soft case pro-4...
7.How to adjust the reed 1.Required jig to adjust reeds we recommend the following toolset. Product name : harmonica repairing tool set (code : 11790) contents : spatula for reed, screw driver (+), edge file (kishage) 2.How to adjust the reed 1.Follow "disassembling procedure". Remove the cover ass'...
