1. DL manuals
  2. Suzuki
  3. Motorcycle
  4. RM-Z250
  5. Owner's Service Manual

Suzuki RM-Z250 Owner's Service Manual

Other manuals for RM-Z250: Owner's Manual

Summary of RM-Z250

  • Page 1

    Part no. 99011-10h50-01a september, 2006 en tk rm-z250 owner’s service manual.

  • Page 2

    This manual should be considered a permanent part of the motorcycle and should remain with the motorcycle when resold or otherwise transferred to a new owner or operator. The manual contains important safety information and instructions which should be read carefully before operating the motorcycle..

  • Page 3: Foreword

    Foreword this manual is presented as a means whereby you can maintain your rm-z250 in top working condi- tion at all times. Your riding skill and the mainte- nance steps outlined in this manual will assure you of top performance from your machine under any type of competition. We sincerely wish you ...

  • Page 4: General Considerations

    General considerations • wear a helmet and goggles a helmet is the most important piece of gear to wear. Helmets do not reduce essential vision or hearing. Generally, helmets do not cause or intensify injury if you crash. Helmets simply help your skull protect your intelligence, your memory, your pe...

  • Page 5: Serial Number Location

    Serial number location the frame number 1 is stamped on the steering head as shown in the photograph. The engine serial num- ber 2 is stamped on the right side of the crankcase assembly. Write down the serial numbers here for your future reference. Frame no. Engine no..

  • Page 6: Warnings For Servicing

    Warnings for servicing ! Warning never run the engine indoors or in a garage. Exhaust gas contains carbon mon- oxide, a gas that is colorless and odorless and can cause death or severe injury. Only run the engine outdoors where there is fresh air. ! Warning hot engine and muffler can burn you. Wait ...

  • Page 7: Precautions For

    Precautions for servicing • replace gaskets, snap rings, circlips, o-rings and cotter pins with new ones. • take care not to expand the end gap larger than required to slip the circlip over the shaft when installing a circlip. • use special tools where specified. • use genuine suzuki parts and recom...

  • Page 8: Symbol Marks And Materials

    Symbol marks and materials listed in the table below are the symbols indicating instructions and other information. The meaning of each symbol is also included in the table. Symbol definition symbol definition torque control required. Data beside it indicates specified torque. Apply thread lock supe...

  • Page 9: Group Index

    Group index general information 1 periodic maintenance 2 troubleshooting 3 machine tuning 4 engine removal and installation 5 cylinder head, cylinder and piston 6 clutch 7 kick starter 8 gearshifting 9 transmission and crankshaft 10 lubrication system 11 fuel system 12 cooling system 13 electrical s...

  • Page 10: General Information

    1 general information 1-1 contents general information country and area codes the following codes stand for the applicable country(-ies) and area(-s). Code country or area effective frame no. 000 e-03 e-19 e-28 japan u.S.A. E.U. Canada js1rj41a000 500001 – js1rj41c 72 100001 – js1rj41a000 500001 – j...

  • Page 11: Location Of Parts

    1-2 general information location of parts 1 clutch lever 2 hot starter lever 3 engine stop switch 4 front brake lever 5 throttle grip 6 fuel tank cap 7 carburetor starter knob 8 gearshift lever 9 front suspension compression damp- ing adjuster 0 front suspension rebound damping adjuster a kick start...

  • Page 12: Accessory

    General information 1-3 accessory side stand this motorcycle is not equipped with a side stand. To support the motorcycle for a short period of time, use the accessory side stand that comes supplied with the motorcycle. When servicing the motorcycle, use a service stand and support the underneath of...

  • Page 13: Operating Instructions

    1-4 general information operating instructions starting the engine inspect the engine oil level, coolant level and air cleaner condi- tion before starting the engine. When the engine is cold: 1) turn the fuel valve lever to the “on” position. 2) shift the transmission into neutral. Note: do not repe...

  • Page 14

    General information 1-5 when the engine is already warm or restarts: 1) pull the hot starter lever 1. 2) kick the engine over, leaving the throttle closed without using the starter knob. 3) return the hot starter lever back immediately after the engine starts. Note: if the engine fails starting, ope...

  • Page 15: Break-In (Running-In)

    1-6 general information break-in (running-in) when the motorcycle is new 1) warm up the engine before starting off. 2) ride for 60 minutes using less than 1/2 throttle opening. 3) ride for 60 minutes using less than 3/4 throttle opening. Note: * the break-in (running-in) period is the period of grea...

  • Page 16: Exterior Parts

    General information 1-7 exterior parts 6 n.M (0.6 kgf.M, 4.5 lb-ft) 16 mm (0.63 in) φ 4.4 mm (0.17 in) 11 mm (0.43 in) φ 15 mm (0.59 in) φ 4.4 mm (0.17 in) 9 mm (0.35 in) φ 16 mm (0.63 in) φ 6 mm (0.24 in) 10 mm (0.39 in) φ.

  • Page 17

    – memo –.

  • Page 18: Periodic Maintenance

    2 periodic maintenance 2-1 contents periodic maintenance periodic maintenance ........................................................................ 2- 3 inspection before practice ...................................................... 2- 3 inspection before race (all items of inspection before pr...

  • Page 19: Periodic Maintenance

    2-2 periodic maintenance contents periodic maintenance exhaust silencer ................................................................................ 2-27 silencer inspection and replacement ................................ 2-27 drive chain and sprockets .............................................

  • Page 20: Periodic Maintenance

    Periodic maintenance 2-3 periodic maintenance inspection before practice what to check check for spark plug heat range, fouled electrode, tightness air cleaner element • dust • lubrication engine oil oil level coolant coolant level cooling system • radiator hose damage • engine coolant leak clutch •...

  • Page 21

    2-4 periodic maintenance inspection before race (all items of inspection before practice on previous page plus) what to check check for clutch clutch disc plates wear and distortion brake pads wear sprockets wear cleanliness fuel tank leakage fuel hose • damage • hoses are connected fuel filter fuel...

  • Page 22

    Periodic maintenance 2-5 periodic maintenance chart it is very important to inspect and maintain the machine regularly. Follow the guideline in the chart. The life of parts varies depending on the riding conditions. Perform more often than shown in the chart if you use the motorcycle under severe co...

  • Page 23

    2-6 periodic maintenance note: r = replace, c = clean, t = tighten, i = inspect and clean, adjust lubricate or replace if necessary, l = lubricate interval races every race every 3 races every 6 races remarks service item hours every 2 hours every 6 hours every 12 hours tire i — — spoke nipple i — —...

  • Page 24: Spark Plug

    Periodic maintenance 2-7 spark plug • remove the seat. ( !5-2) • remove the radiator covers and fuel tank. ( !5-2) • disconnect the lead wire coupler from the ignition coil/plug cap. • remove the ignition coil/plug cap. • remove the spark plug with a spark plug wrench. Note: remove the dirt around t...

  • Page 25

    2-8 periodic maintenance • check the spark plug gap a with a thickness gauge. " 09900-20803: thickness gauge # spark plug gap: 0.9 – 1.0 mm (0.035 – 0.039 in) # standard spark plug • tighten the spark plug with specified tightening torque after tightening the spark plug temporarily with fingers. " 0...

  • Page 26: Air Cleaner

    Periodic maintenance 2-9 air cleaner air cleaner element removal • remove the left frame cover. • remove the wing nut 1. • remove the element 2 from the element holder. Washing • fill a washing pan large enough to hold the element with a non-flammable cleaning solvent a. Immerse the element in the s...

  • Page 27: Engine Oil And Oil Filter

    2-10 periodic maintenance note: follow the instructions below to keep the air cleaner element dry when cleaning the motorcycle. • cover the element with vinyl bag. • install the left frame cover. • cover the inlet hole on the frame cover in order to prevent water from coming into the air cleaner box...

  • Page 28

    Periodic maintenance 2-11 inspection before engine oil level check • before starting the engine, check that there is sufficient oil for operating the engine. Note: the oil level measurement may become inaccurate unless the motorcycle is held upright as the motorcycle inclination affects the oil leve...

  • Page 29

    2-12 periodic maintenance engine oil change • during inspection, hold the motorcycle in an upright position on a level surface. • warm up the engine. • remove the filler cap, tdc plug 1, drain plug 2 and drain no.2 plug 3. Drain oil thoroughly. • replace the gasket washers with new ones and tighten ...

  • Page 30

    Periodic maintenance 2-13 engine oil filter change • drain the engine oil as described in the engine oil replace- ment procedure. • remove the oil filter cap 1 and spring 2 with oil filter 3. • apply engine oil lightly to the gasket of the new oil filter before installation. • install the new oil fi...

  • Page 31: Oil Strainers

    2-14 periodic maintenance oil strainers oil strainer (feed pump side) removal • drain engine oil. ( !2-12) • remove the engine oil strainer cap. • pull out the oil strainer. Note: we recommend that inspect feed pump side oil strainer every race. Oil strainer (scavenge pump side) removal ( !10-4) ins...

  • Page 32: Engine Coolant

    Periodic maintenance 2-15 engine coolant engine coolant level check • remove the radiator cap 1. • check that the engine coolant level is at the bottom of the inlet hole. If not, replenish the radiator with specified engine cool- ant. • tighten the radiator cap securely. Note: * this motorcycle does...

  • Page 33

    2-16 periodic maintenance engine coolant replenishment • use an anti-freeze and summer engine coolant which is com- patible with aluminum radiator, mixed with distilled water at the ratio of 50:50. Note: the radiator, cylinder and cylinder head are made of aluminum alloy. Using non-recommended engin...

  • Page 34: Clutch Cable

    Periodic maintenance 2-17 clutch cable adjust the clutch cable play as follows: major adjustment • loosen the lock-nut 1. • turn adjuster 2 so the clutch lever has 10 – 15 mm (0.4 – 0.6 in) play at the clutch lever end before pressure is felt. • tighten the lock-nut 1 to the specified torque. # clut...

  • Page 35: Throttle Cable

    2-18 periodic maintenance throttle cable adjust the throttle cable play a as follows: throttle cable adjustment • loosen the lock-nut 1. • turn adjuster 2 so the throttle grip has 2 – 4 mm (0.08 – 0.16 in) play in circumference. • tighten the lock-nut 1 to the specified torque. # throttle cable play...

  • Page 36: Hot Starter

    Periodic maintenance 2-19 hot starter adjust the hot starter cable play a as follows: • loosen the lock-nut 1. • turn adjuster 2 so the hot starter lever clearance a mea- sured at the lever holder obtains approx. 3 mm (0.12 in) when squeezing the lever until pressure is felt. • tighten the lock-nut ...

  • Page 37: Engine Idle Speed

    2-20 periodic maintenance engine idle speed • adjust the throttle cable play. ( !2-18) • warm up the engine. • connect the multi-circuit tester to the primary lead wire (w/bl). " 09900-25008: multi-circuit tester set • start the engine, turn the throttle stop screw 1 and set the engine idle speed as...

  • Page 38: Fuel Hose

    Periodic maintenance 2-21 fuel hose • inspect the fuel hose for damage and fuel leakage. If any defects are found, the fuel hose must be replaced. • replace the fuel hose every four years. Fuel filter • drain fuel from the fuel tank. • remove the seat and radiator covers. ( !5-2) • turn the fuel val...

  • Page 39: Valve Clearance

    2-22 periodic maintenance valve clearance • remove the seat. ( !5-2) • remove the radiator covers and fuel tank. ( !5-2) • disconnect the ignition coil/plug cap. ( !2-7) • remove the spark plug. ( !2-7) • remove the cylinder head cover and its cylinder head cover gasket. The valve clearance specific...

  • Page 40

    Periodic maintenance 2-23 valve clearance adjustment the clearance is adjusted by replacing the existing tappet shim by a thicker or thinner shim. • remove the intake or exhaust camshafts. ( !6-4) • remove the tappet 1 and shim 2 by fingers or magnetic hand. • check the figures printed on the shim. ...

  • Page 41

    2-24 periodic maintenance (intake side) 0.015 – 0.039 0.040 – 0.064 0.065 – 0.089 0.090 – 0.160 0.000– 0.014 0.161 – 0.185 0.186 – 0.210 0.211 – 0.235 0.236 – 0.260 0.261 – 0.285 0.286 – 0.310 0.311 – 0.335 0.336 – 0.360 0.361 – 0.385 0.386 – 0.410 0.411 – 0.435 0.436 – 0.460 0.461 – 0.485 0.486 – 0...

  • Page 42

    Periodic maintenance 2-25 (exhaust side) 0.070 – 0.094 0.095 – 0.119 0.120 – 0.144 0.145 – 0.169 0.045 – 0.069 0.020 – 0.044 0.000 – 0.019 0.170 – 0.240 0.241 – 0.265 0.266 – 0.290 0.291 – 0.315 0.316 – 0.340 0.341– 0.365 0.366 – 0.390 0.391 – 0.415 0.416 – 0.440 0.441 – 0.465 0.466 – 0.490 0.491 – ...

  • Page 43: Piston

    2-26 periodic maintenance cylinder head, cylinder and piston cylinder head inspection • remove the cylinder head. ( !6-4) • decarbonize the combustion chambers. • inspect for pinholes, cracks and other damage. • if any defects are found, replace the cylinder head with a new one. Cylinder inspection ...

  • Page 44: Exhaust Silencer

    Periodic maintenance 2-27 exhaust silencer silencer inspection and replacement • remove the muffler. ( !5-3) • remove the bands 1 and rivets using the 5.0 mm (0.20 in) drill. Note: be careful not to damage the rear muffler body, tail pipe and inner plate. • remove the rear muffler body 2 and inner p...

  • Page 45: Drive Chain And Sprockets

    2-28 periodic maintenance drive chain and sprockets drive chain slack • place the motorcycle on a block to lift the rear wheel off the ground. • inspect the drive chain slack at the middle point between the drive chain buffer and rear sprocket. # drive chain slack: 35 – 45 mm (1.4 – 1.8 in) drive ch...

  • Page 46

    Periodic maintenance 2-29 drive chain lubrication • remove the chain clip and master link from the drive chain and remove the drive chain. Note: be careful not to bend the chain clip. • inspect for wear and damage of the drive chain and replace it if necessary. • clean the drive chain with non-flamm...

  • Page 47: Chain Roller

    2-30 periodic maintenance drive chain guide, buffer and chain roller drive chain guide inspection • inspect the drive chain guide 1 for bends and damage. Note: the drive chain can hit a bent guide causing noise and drive chain wear. • inspect the chain guide defense 2 for wear. • replace the defecti...

  • Page 48: Brakes

    Periodic maintenance 2-31 brakes brake fluid level • inspect the brake fluid level in both front and rear reservoirs. If the brake fluid level is lower than lower mark a, replenish the reservoir with the specified brake fluid to the upper line. ( !16-3) inspect brake pad wear and brake fluid leakage...

  • Page 49

    2-32 periodic maintenance brake pad • inspect the brake pads for wear. If the brake pads are worn, replace them with new ones. ( !16-5) note: * pump the brake lever and pedal several times to restore the brake pads after replacing the brake pads. * replace both right and left pads together when repl...

  • Page 50: Front Fork

    Periodic maintenance 2-33 front fork • move the front fork up and down several times and inspect for smooth movement. • inspect for damage and oil leaks. • inspect the bolts and nuts for tightness. • if any defects are found, replace the front fork with a new one. • place a stand under the chassis t...

  • Page 51: Steering

    2-34 periodic maintenance spoke nipple and rim lock inspection • inspect the spokes for tension by squeezing the spoke nip- ples. • retighten the spoke nipples with a spoke nipple wrench so as all spokes have same tension. $ spoke nipple: 6 n·m (0.6 kgf-m, 4.5 lb-ft) • inspect the rim lock 1 for tig...

  • Page 52: Lubrication

    Periodic maintenance 2-35 lubrication apply grease or oil to the moving parts to increase durability and prevent wear. The following materials are necessary: a. Lightweight oil such as wd-40 or penetrating oil b. Aerosol type chain lube c. Suzuki super grease “a” (or equivalent grease) or water-proo...

  • Page 53: Compression Pressure Check

    2-36 periodic maintenance compression pressure check the compression pressure reading of a cylinder is a good indicator of its internal condition. The decision to replace the cylinder is often based on the results of a compression test. Compression pressure specification (automatic decomp. Actuated)...

  • Page 54: Oil Pressure Check

    Periodic maintenance 2-37 oil pressure check check the oil pressure periodically. This will give a good indication of the condition of the moving parts. # oil pressure: low or high oil pressure can indicate any of the following conditions: low oil pressure * clogged oil filter * oil leakage from the...

  • Page 55

    – memo –.

  • Page 56: Troubleshooting

    3 18 troubleshooting 3-1 contents troubleshooting engine ........................................................................................................ 3- 2 carburetor ............................................................................................ 3- 6 radiator (cooling system...

  • Page 57: Engine

    3-2 troubleshooting engine complaint symptom and possible causes remedy engine will not start or is hard to start. Compression too low • valve clearance out of adjustment • worn valve guides or poor seating of valves • mistiming valves • excessively worn piston ring • worn-down cylinder bore • poor ...

  • Page 58

    Troubleshooting 3-3 complaint symptom and possible causes remedy noisy engine excessive valve chatter • too large valve clearance • weakened or broken valve springs • worn tappet or cam surface • worn and burnt camshaft journal noise seems to come from piston • worn down piston or cylinder • combust...

  • Page 59

    3-4 troubleshooting complaint symptom and possible causes remedy engine lacks power. Defective engine internal parts • loss of valve clearance • weakened valve springs • valve timing out of adjustment • worn piston ring or cylinder • poor seating of valves • fouled spark plug • incorrect spark plug ...

  • Page 60

    Troubleshooting 3-5 complaint symptom and possible causes remedy slipping clutch • weakened clutch springs • worn or distorted pressure plate • worn or distorted clutch plates • insufficient clutch cable play replace replace replace adjust dragging clutch • some clutch spring weakened while others a...

  • Page 61: Carburetor

    3-6 troubleshooting carburetor radiator (cooling system) complaint symptom and possible causes remedy starting difficulty. • improperly working starter knob • improperly working hot starter lever • clogged starter jet passage • maladjusted pilot screw • maladjusted throttle stop screw • clogged slow...

  • Page 62: Chassis

    Troubleshooting 3-7 chassis complaint symptom and possible causes remedy heavy steering • overtightened steering stem nut • broken bearing in steering stem • distorted steering stem • not enough pressure in tires adjust replace replace adjust wobbly handlebars • loss of balance between right and lef...

  • Page 63: Brakes

    3-8 troubleshooting brakes complaint symptom and possible causes remedy insufficient brake power • leakage of brake fluid from hydraulic system • worn pads • oil adhesion of engaging surface of pads • worn disc • air in hydraulic system • not enough brake fluid in the reservoir repair or replace rep...

  • Page 64: Electrical

    Troubleshooting 3-9 electrical complaint symptom and possible causes remedy no sparking or poor sparking • defective ignition coil/plug cap • defective spark plug • defective cdi unit • defective magneto • open-circuited wiring connections replace replace replace replace check and repair spark plug ...

  • Page 65

    – memo –.

  • Page 66: Machine Tuning

    4 machine tuning 4-1 contents machine tuning carburetor tuning ............................................................................. 4- 2 principles of carburetor tuning .......................................... 4- 2 slow system .................................................................

  • Page 67: Carburetor Tuning

    4-2 machine tuning carburetor tuning the carburetion of your motorcycle is carefully selected after extensive testing. You will find that the carbu- retion will function smoothly under many varied operating conditions. For best results we recommend that the adjustments and carburetion jetting be lef...

  • Page 68

    Machine tuning 4-3 as shown below, each of the asterisk (*) marked parts is located between the air/fuel passage and has its own air/fuel mixture adjustable range in terms of the throttle valve opening. The chart indicates that the car- buretor can supply correct air/fuel mixture to the engine in an...

  • Page 69

    4-4 machine tuning pilot screw (p.S.) the pilot screw controls volume of the air/fuel mixture in slow range. Pilot screw specifications indicate the number of turns back from the lightly seated position. Throttle stop screw the throttle stop screw determines the full closed position of the throttle ...

  • Page 70

    Machine tuning 4-5 main system main jet (m.J.) the main jet, like the slow jet, meters fuel flow. Each jet size is indicated by a number. Larger number means a larger bore diameter and fitting a larger number main jet enriches the air/fuel mixture. * included alternated parts intermediate system jet...

  • Page 71

    4-6 machine tuning jet needle clip position to adjust the air/fuel mixture with the jet needle, change position of the needle clip which is set in the 4th groove. The lower groove the clip is moved to, the higher the jet needle rises and the larger the clearance with the main nozzle becomes, resulti...

  • Page 72

    Machine tuning 4-7 carburetor tuning in practice in the previous section, basic principles of carburetor tuning have been discussed. Described in this section are the bases for carburetor tuning required when coping with variations in air (oxygen) concentration. Variation in air (oxygen) concentrati...

  • Page 73

    4-8 machine tuning judging air/fuel mixture for proper carburetor tuning, it is necessary to know how to judge the air/fuel mixture made in the carburetor; whether too rich, too lean or properly mixed. Given below are the symptoms observed when the engine is not supplied with the proper air/fuel mix...

  • Page 74

    Machine tuning 4-9 jet needle shaded: standard * : included alternate parts none : optional parts 1 adjustment of slow system 1) set the pilot screw as specified. 2) see if the selected slow jet is correct or not by judging the air/fuel mixture. If air/fuel mixture is rich, replace it with smaller o...

  • Page 75: Front Fork Tuning

    4-10 machine tuning front fork tuning the front fork compression and rebound damping force, and oil level are adjustable for rider’s preference, rider’s weight and course condition. Note: * break-in new front forks before attempting adjustment. * be sure to adjust both right and left front forks equ...

  • Page 76

    Machine tuning 4-11 oil quantity minor adjustment adding the fork oil • remove the air bleed screw 1. • add the fork oil with a injector from the air bleed hole. Reducing the fork oil • remove the front forks. ( !17-4) • remove the air bleed screw. • leaning the front fork, reduce the fork oil from ...

  • Page 77

    4-12 machine tuning oil change (only for outer tube oil chamber) • remove the front forks. ( !17-4) • thoroughly clean the fork before disassembly. • clamp the outer tube with a vise. Protect the outer tube with a rag when using a vise. ( !17-5) • loosen and remove the fork cap bolt (sub-tank) from ...

  • Page 78

    Machine tuning 4-13 • slide down the outer tube. • pour the specified amount of fork oil into the outer tube. # 99000-99001-ss5: suzuki fork oil ss-05 (or equivalent fork oil) note: be sure to adjust the fork oil quantity within the above-men- tioned range. • raise the outer tube and temporarily tig...

  • Page 79

    4-14 machine tuning spring change • remove the front forks. ( !17-4) • thoroughly clean the fork before disassembly. • remove the fork cap bolt and drain fork oil. ( !17-5) • loosen the center bolt completely. ( !17-6) • compress the outer tube by hands and install the conrod holder (special tool) b...

  • Page 80

    Machine tuning 4-15 • make sure approx. 10 mm (0.39 in) of inner rod thread is exposed on the end. ( !17-14) • install the damper rod assembly. ( !17-14) • insert the push rod into the inner rod. • insert the shaped projection of center bolt into the push rod. ( !17-15) • check or adjust the clearan...

  • Page 81

    4-16 machine tuning front fork tuning procedure test ride the motorcycle and find out how the front suspension reacts on various types of surface. According to the symptom noticed, adjust the front fork to the best setting for rider and race track conditions. To adjust, attempt changing fork oil cap...

  • Page 82: Rear Suspension Tuning

    Machine tuning 4-17 rear suspension tuning the rear suspension compression and rebound damping force, and spring pre-load are adjustable for rider’s preference, rider’s weight and course condition. Note: * break-in the rear suspension when riding with a new rear cushion unit. ( !1-6) * inspect the f...

  • Page 83

    4-18 machine tuning rebound damping force adjustment note: to set the adjuster, you must gently turn the adjust screw clock- wise until it stops, then back it out the recommended number of turns. Do not force the adjust screw past the stopped position, or you may damage the adjuster. • turn the adju...

  • Page 84

    Machine tuning 4-19 rear suspension tuning procedure • adjust the rear suspension according to the rider’s weight and preference by referring to the table below. • measure the distance l1 from the seat bolt to the chain adjuster lock-nut with the motorcycle on the stand and the rear wheel lifted off...

  • Page 85

    4-20 machine tuning after the sag measurement has been set 100 mm (3.94 in), test ride the motorcycle and adjust the suspen- sion for the rider and track conditions referring to the guide below. Note: when adjusting the damping force setting, attempt turning the adjuster 1 to 2 click stops at a time...

  • Page 86: Suspension Balance

    Machine tuning 4-21 suspension balance balancing the front to rear suspension properly is the most critical adjustment for suspension performance. If the front forks are adjusted harder than the rear suspension, such as changing to heavier front fork oil, stiffer compression and rebound setting, air...

  • Page 87

    – memo –.

  • Page 88

    5 engine removal and installation 5-1 contents engine removal and installation engine removal and installation ................................................. 5- 2 removal ............................................................................................. 5- 2 installation .................

  • Page 89

    5-2 engine removal and installation engine removal and installation removal • drain engine oil. ( !2-12) • drain engine coolant. ( !13-3) • remove the seat 1. • remove the radiator covers 2, left and right. • remove the right frame cover 3. • place the jack under the frame to support the motorcycle....

  • Page 90

    Engine removal and installation 5-3 • remove the muffler 5. • remove the exhaust pipe 6 and exhaust pipe gasket 7. • remove the front protector. • remove the radiator mounting bolts, left and right. • disconnect the radiator hose 8, 9. • remove the radiator hose 0..

  • Page 91

    5-4 engine removal and installation • disconnect the magneto lead wire coupler a and clamp. • disconnect the clutch cable b. • remove the carburetor. ( !12-5) • remove the ignition coil/plug cap. ( !2-7) • remove the cotter pin c, washer d and clip e. • remove the kick starter lever f. • remove the ...

  • Page 92

    Engine removal and installation 5-5 • remove the drive chain clip m and release the drive chain. • remove the snap ring n and engine sprocket o. # 09900-06107: snap ring pliers • remove the engine mounting upper brackets p, left and right. • remove the engine mounting front brackets q, left and righ...

  • Page 93

    5-6 engine removal and installation installation install the engine in the reverse order of removal. Pay attention to the following points: • fit the swingarm in its position and hold it with the swingarm pivot shaft. • mount the engine on the frame. • tighten the engine mounting bolts, nuts and swi...

  • Page 94

    Engine removal and installation 5-7 • tighten the engine sprocket cover bolts to the specified torque. $ engine sprocket cover bolt: 11 n·m (1.1 kgf-m, 8.0 lb-ft) • install the gearshift lever in the correct position. • apply grease to the brake pedal pivot bolt. % 99000-25010: suzuki super grease “...

  • Page 95

    5-8 engine removal and installation • install the muffler joint connector a and exhaust pipe gasket b. • temporarily tighten the exhaust pipe nuts c. • insert the muffler to the exhaust pipe. • temporarily tighten the muffler mounting front bolt d and rear bolt e. • temporarily tighten the connector...

  • Page 96

    6 cylinder head, cylinder and piston 6-1 contents cylinder head, cylinder and piston construction ........................................................................................ 6- 2 cylinder head, cylinder and piston ...................................... 6- 2 engine top side ................

  • Page 97: Construction

    6-2 cylinder head, cylinder and piston construction cylinder head, cylinder and piston 50 n.M (5.0 kgf-m, 36.0 lb-ft) 10 n.M (1.0 kgf-m, 7.0 lb-ft) 12 n.M (1.2 kgf-m, 8.5 lb-ft) 10 n.M 1.0 kgf-m, 7.0 lb-ft 23 n.M 2.3 kgf-m, 16.5 lb-ft 12 n.M 1.2 kgf-m, 8.5 lb-ft 10 n.M 1.0 kgf-m, 7.0 lb-ft 10 n.M 1....

  • Page 98: Engine Top Side

    Cylinder head, cylinder and piston 6-3 engine top side cylinder head cover removal • remove the seat. ( !5-2) • remove the radiator covers and fuel tank. ( !5-2) • disconnect the ignition coil/plug cap and remove the spark plug. ( !2-7) • remove the cylinder head cover 1 and cylinder head cover gask...

  • Page 99

    6-4 cylinder head, cylinder and piston • remove the cam chain tension adjuster cap bolt 3, bar and spring. • remove the cam chain tension adjuster 4 and its gasket. • remove the camshaft journal holders 5. Note: loosen the camshaft journal holder bolts diagonally. • disengage the camshafts 7 from ca...

  • Page 100

    Cylinder head, cylinder and piston 6-5 • remove the cylinder head base nuts 3. • loosen the cylinder base bolt 4. • remove the cylinder head bolts and washers. Note: when loosening the cylinder head bolts, loosen each bolt little by little diagonally. • remove the cylinder head 5. Note: if the cylin...

  • Page 101

    6-6 cylinder head, cylinder and piston • remove the cylinder gasket 2 and dowel pins. Piston and piston ring removal • remove the cylinder. ( !6-5) • place a clean rag over the cylinder base to prevent the piston pin circlip 1 from dropping into the crankcase. • remove the piston pin circlip 1. • re...

  • Page 102

    Cylinder head, cylinder and piston 6-7 cam chain, cam chain tensioner and cam chain guide removal • remove the cylinder head. ( !6-4) • remove the magneto cover and magnet rotor. ( !14-12) • remove the cam chain guide retainer 1 and cam chain no.1 guide 2. • remove the cam chain 3. • remove the cam ...

  • Page 103: Engine Top Components

    6-8 cylinder head, cylinder and piston engine top components inspection and service automatic decomp. Inspection • check the decomp. Cam moves smoothly and shaft 1 rotates together. • if any abnormal condition are found, replace the camshaft assembly. Camshaft inspection cam sprocket • inspect the s...

  • Page 104

    Cylinder head, cylinder and piston 6-9 cam wear • measure the cam height h using the micrometer. • replace a camshaft if the cams are worn to the service limit. " cam height h: service limit in.: 34.56 mm (1.361 in) ex.: 34.08 mm (1.342 in) # 09900-20202: micrometer (25 – 50 mm) camshaft journal wea...

  • Page 105

    6-10 cylinder head, cylinder and piston • if the camshaft journal oil clearance measured exceeds the limit, measure the inside diameter of the camshaft journal holder and outside diameter of the camshaft journal. • replace the camshaft or the cylinder head depending upon which one exceeds the specif...

  • Page 106

    Cylinder head, cylinder and piston 6-11 cam chain no.1 guide, cam chain no.2 guide and cam chain tensioner inspection • inspect the contacting surface of the cam chain guides and cam chain tensioner. • if it is worn or damaged, replace it with a new one. Cylinder head and valve inspection valve disa...

  • Page 107

    6-12 cylinder head, cylinder and piston (exhaust side) • install the sleeve protector a between the valve spring and cylinder head. • using the special tools, compress the valve spring and remove the two cotter halves 3 from the valve stem. # 09916-14510: valve lifter 09916-14530: attachment 09916-8...

  • Page 108

    Cylinder head, cylinder and piston 6-13 cylinder head distortion • decarbonize the combustion chamber. • check the gasket surface of the cylinder head for distortion with a straightedge and thickness gauge, taking a clearance reading at several places indicated. • if the largest reading at any posit...

  • Page 109

    6-14 cylinder head, cylinder and piston valve stem deflection • lift the valve about 10 mm (0.39 in) from the valve seat. • measure the valve stem deflection in two directions, perpen- dicular to each other, by positioning the dial gauge as shown. • if the deflection measured exceeds the limit, then...

  • Page 110

    Cylinder head, cylinder and piston 6-15 • cool down the new valve guides in a freezer for about one hour and heat the cylinder head to 100 – 150 °c (212 – 302 °f) with a hot plate. • apply engine oil to the valve guide hole. • drive the valve guide into the hole using the valve guide installer 1 and...

  • Page 111

    6-16 cylinder head, cylinder and piston • if the seat width w measured exceeds the standard value or seat width is not uniform, refuse the seat using the seat cutter. " valve seat width w: standard: 0.9 – 1.1 mm (0.035 – 0.043 in) valve seat servicing the valve seats 1 for both the intake and exhaus...

  • Page 112

    Cylinder head, cylinder and piston 6-17 • clean and assemble the head and valve components. Fill the intake and exhaust ports with gasoline to check for leaks. • if any leaks occur, inspect the valve seat and face for burrs or other things that could prevent the valve from sealing. Valve spring • ch...

  • Page 113

    6-18 cylinder head, cylinder and piston • install the valve spring with the small-pitch portion a facing cylinder head. A small-pitch portion b large-pitch portion c upward d paint • put on the valve spring retainer 2, and using the valve lifter and sleeve protector a (only for exhaust side), press ...

  • Page 114

    Cylinder head, cylinder and piston 6-19 intake pipe removal • remove the intake pipe 1. Intake pipe installation • install the intake pipe. Note: fit the recess a of the intake pipe into the projection b of the cylinder head..

  • Page 115

    6-20 cylinder head, cylinder and piston cylinder inspection cylinder distortion • check the gasketed surface of the cylinder for distortion with a straightedge and thickness gauge, taking a clearance read- ing at several places indicated. • if the largest reading at any position of the straightedge ...

  • Page 116

    Cylinder head, cylinder and piston 6-21 piston and piston ring inspection piston diameter • using a micrometer, measure the piston outside diameter at 8.5 mm (0.33 in) a from the piston skirt end. • if the measurement is less than the limit, replace the piston. " piston diameter: service limit: 76.8...

  • Page 117

    6-22 cylinder head, cylinder and piston piston ring-to-groove clearance • decarbonize the piston ring and piston ring groove. • measure the side clearances of the 1st piston ring using the thickness gauge. • if any of the clearances exceed the limit, replace both the pis- ton and piston ring. # 0990...

  • Page 118

    Cylinder head, cylinder and piston 6-23 crankshaft and conrod inspection for inspection other than the following, refer to page 10-7,-8. Conrod small end i.D. • using a small bore gauge, measure the inside diameter of the conrod small end. • if the inside diameter of the conrod small end exceeds the...

  • Page 119

    6-24 cylinder head, cylinder and piston cam chain, cam chain tensioner and cam chain guide installation install the cam chain and cam chain tensioner in the reverse order of removal. Pay attention to the following points: • install the cam chain tensioner 1. $ cam chain tensioner bolt: 10 n·m (1.0 k...

  • Page 120

    Cylinder head, cylinder and piston 6-25 piston and piston ring installation install the piston and piston ring in the reverse order of removal. Pay attention to the following points: piston ring • install the piston rings in the order of oil ring and 1st ring. • the first member to go into the oil r...

  • Page 121

    6-26 cylinder head, cylinder and piston piston • install the piston with the punch mark 1 facing towards the exhaust side. • before installing the piston pin, apply molybdenum oil solution onto its surface. % molybdenum oil solution • place a clean rag over the cylinder base to prevent the piston pi...

  • Page 122

    Cylinder head, cylinder and piston 6-27 cylinder and cylinder head installation install the cylinder and cylinder head in the reverse order of removal. Pay attention to the following points: cylinder • thoroughly wipe off oil from the fitting surface of the crank- case. • apply suzuki bond to the cr...

  • Page 123

    6-28 cylinder head, cylinder and piston cylinder head • install the dowel pins into the cylinder and then install the cyl- inder head gasket 1 onto the cylinder. • place the cylinder head 2 on the cylinder. • install the gasket washers to the cylinder head bolts as shown. • apply engine oil to the w...

  • Page 124

    Cylinder head, cylinder and piston 6-29 camshaft (automatic decomp.) and cam chain tension adjuster installation install the camshaft and cam chain tension in the reverse order of removal. Pay attention to the following points: camshaft (automatic decomp.) • place a wrench over the crankshaft and tu...

  • Page 125

    6-30 cylinder head, cylinder and piston • pull the exhaust side of the cam chain taut to install the camshaft sprocket (exhaust side). • turn the exhaust camshaft so that the timing mark c is aligned with the gasket surface of the cylinder head. Engage the cam chain with the exhaust camshaft sprocke...

  • Page 126

    Cylinder head, cylinder and piston 6-31 cam chain tension adjuster • retract the push rod by pushing the stopper 1. • apply suzuki super grease to the o-ring 2. ( 99000-25010: suzuki super grease “a” (or equivalent grease) • install the cam chain tension adjuster 3 as shown. • tighten the cam chain ...

  • Page 127

    6-32 cylinder head, cylinder and piston • after installing the cam chain tension adjuster, rotate the crankshaft (two turns), and recheck the positions of the cam- shafts. ( !6-30) • inspect the valve clearance. ( !2-22) • apply suzuki super grease to the o-rings. ( 99000-25010: suzuki super grease ...

  • Page 128

    Cylinder head, cylinder and piston 6-33 cylinder head cover installation install the cylinder head cover in the reverse order of removal. Pay attention to the following points: • install the gasket to the cylinder head cover. • apply suzuki bond to the end caps of the cylinder head cover gasket as s...

  • Page 129

    – memo –.

  • Page 130: Clutch

    7 clutch 7-1 contents clutch construction ........................................................................................ 7- 2 clutch ................................................................................................ 7- 2 clutch plate .............................................

  • Page 131: Construction

    7-2 clutch construction clutch 10 n.M (1.0 kgf-m, 7.0 lb-ft) 90 n.M (9.0 kgf-m, 65.0 lb-ft).

  • Page 132: Clutch Plate

    Clutch 7-3 clutch plate removal • drain engine oil. ( !2-12) • remove the brake pedal. ( !16-18) • remove the clutch cover 1 and its gasket. • hold the clutch housing with the special tool. " 09920-53740: clutch sleeve hub holder • remove the clutch spring set bolts and clutch springs. Note: loosen ...

  • Page 133

    7-4 clutch • remove the clutch drive plates 6 and driven plates 7. Inspection drive plate • measure the drive plate thickness. # drive plate thickness service limit: 2.42 mm (0.095 in) " 09900-20101: vernier calipers (150 mm) • inspect the drive plates for wear, distortion and discoloration. • if th...

  • Page 134

    Clutch 7-5 clutch spring • measure the clutch spring free length. • replace all the springs if any spring is not within the limit. Note: replace five clutch springs together even if only one spring is beyond the service limit. # clutch spring free length service limit: 43.0 mm (1.69 in) " 09900-2010...

  • Page 135

    7-6 clutch installation install the clutch plates in the reverse order of removal. Pay attention to the following points: • apply engine oil to the drive plates 1 and driven plates 2. • install the push rod and push piece. • apply engine oil to the release bearing 3. Note: the covered side a of the ...

  • Page 136: Sleeve Hub

    Clutch 7-7 primary driven gear and clutch sleeve hub removal • remove the clutch cover. ( !7-3) • remove the pressure plate and clutch plates. ( !7-3, -4) • flatten the lock washer 1. • hold the clutch sleeve hub 2 with the special tool and loosen the nut 3. " 09920-53740: clutch sleeve hub holder •...

  • Page 137

    7-8 clutch inspection • inspect the clutch sleeve hub and primary driven gear for wear and cracks. • if necessary, replace the sleeve hub or driven gear. • inspect the needle bearing and spacer for damage and wear. • if any defects are found, replace the bearing or spacer. Installation install the p...

  • Page 138

    Clutch 7-9 • tighten the clutch sleeve hub nut with the special tool to the specified torque. " 09920-53740: clutch sleeve hub holder $ clutch sleeve hub nut: 90 n·m (9.0 kgf-m, 65.0 lb-ft) • make sure the clutch sleeve hub for smooth movement. • bend the lock washer to secure the nut. • reassemble ...

  • Page 139: Clutch Release Camshaft

    7-10 clutch clutch release camshaft removal • remove the cam chain tension adjuster. ( !6-4) • disconnect the clutch cable 1 and remove the retainer 2. • pull the clutch release camshaft 3 out of crankcase. Inspection clutch release camshaft • inspect the clutch release camshaft for abnormal deflect...

  • Page 140

    Clutch 7-11 installation • apply suzuki moly paste to the clutch release camshaft. % 99000-25140: suzuki moly paste • apply engine oil to the oil seal lip. • install the clutch release camshaft 1. • connect the clutch cable 2 and install the retainer 3. • install the cam chain tension adjuster. ( !6...

  • Page 141

    – memo –.

  • Page 142: Kick Starter

    8 kick starter 8-1 contents kick starter construction ........................................................................................ 8- 2 kick starter .................................................................................... 8- 2 kick starter .......................................

  • Page 143: Construction

    8-2 kick starter construction kick starter 10 n·m (1.0 kgf-m, 7.0 lb-ft).

  • Page 144: Kick Starter

    Kick starter 8-3 kick starter removal • drain engine oil. ( !2-12) • drain engine coolant. ( !13-3) • remove the brake pedal. ( !16-18) • disconnect the radiator hose 1. • remove the kick starter lever 2. • remove the right crankcase cover 3, dowel pins and gasket. • remove the clutch assembly. ( !7...

  • Page 145

    8-4 kick starter • remove the kick starter guide f. Inspection • inspect the oil seal lip for wear and damage. • if any defects are found, replace the oil seal with a new one. • inspect the kick starter drive gear teeth for damage. • inspect the kick starter drive gear ratchet part for wear and dama...

  • Page 146

    Kick starter 8-5 installation install the kick starter in the reverse order of removal. Pay atten- tion to the following points: • install the kick starter guide 1. # kick starter guide bolt: 10 n·m (1.0 kgf-m, 7.0 lb-ft) • install the kick starter drive gear 2, washers and snap ring 3 to the kick s...

  • Page 147

    8-6 kick starter • install the spring 7 to the kick starter shaft. • install the kick starter shaft assembly to the crankcase. Note: securely engage the stopper portion e of the kick starter with the stopper guide f. • install the end of return spring to the crankcase. • install the kick starter idl...

  • Page 148

    Kick starter 8-7 • install the kick starter lever onto the kick starter shaft. Note: when installing the kick starter lever, align the wide spline teeth g and h. • tighten the kick starter lever bolt to the specified torque. # kick starter lever bolt: 23 n·m (2.3 kgf-m, 16.5 lb-ft) • install the bra...

  • Page 149

    – memo –.

  • Page 150: Gearshifting

    9 gearshifting 9-1 contents gearshifting construction ........................................................................................ 9- 2 gearshift linkage ......................................................................... 9- 2 gearshift linkage ........................................

  • Page 151: Construction

    9-2 gearshifting construction gearshift linkage 23 n.M (2.3 kgf-m, 16.5 lb-ft) 24 n.M (2.4 kgf-m, 17.5 lb-ft) 10 n.M (1.0 kgf-m, 7.0 lb-ft).

  • Page 152: Gearshift Linkage

    Gearshifting 9-3 gearshift linkage removal • drain engine oil. ( !2-12) • drain engine coolant. ( !13-3) • remove the gearshift lever 1. Note: mark the gearshift shaft head at which the gearshift lever slit set for correct reinstallation. • remove the right crankcase cover and clutch assembly. ( !7-...

  • Page 153

    9-4 gearshifting • remove the gearshift pawls 8, pins 9 and springs 0. • remove the gearshift cam driven gear pin a and gearshift cam stopper plate b. • remove the gearshift cam stopper c, spring d and washer e. • remove the gearshift arm stopper f and washer g..

  • Page 154

    Gearshifting 9-5 inspection • inspect the gearshift shaft 1 for bends and damage. • inspect the return spring 2 for damage. • replace the defective parts with a new one if necessary. • inspect the pawls 3, pins 4 and springs 5 for damage. • replace the defective parts with a new one if necessary. In...

  • Page 155

    9-6 gearshifting • apply a small quantity of thread lock to the gearshift cam driven pin 6 and tighten it to the specified torque. % 99000-32050: thread lock “1342” $ gearshift cam driven pin: 24 n·m (2.4 kgf-m, 17.5 lb-ft) • fit the springs 7, pins 8 and pawls 9 to the gearshift cam driven gear 0. ...

  • Page 156

    Gearshifting 9-7 • install the gearshift return spring c, snap ring d and washer e to the gearshift shaft b properly. Note: when installing the return spring, position the stopper d of gearshift arm between the return spring ends e. " 09900-06107: snap ring pliers • install the gearshift shaft assem...

  • Page 157

    – memo –.

  • Page 158: Transmission and Crankshaft

    10 transmission and crankshaft 10-1 contents transmission and crankshaft construction ...................................................................................... 10- 2 transmission and crankshaft ............................................... 10- 2 engine bottom side .......................

  • Page 159: Construction

    10-2 transmission and crankshaft construction transmission and crankshaft 90 n.M (9.0 kgf-m, 65.0 lb-ft).

  • Page 160: Engine Bottom Side

    Transmission and crankshaft 10-3 engine bottom side • remove the engine. ( !5-2 to -5) note: the following parts must be removed before disassembling the engine bottom side (crankcase). • disconnect the crankcase breather hose 1. • remove the cylinder head, cylinder and piston. ( !6-3 to -6) • remov...

  • Page 161

    10-4 transmission and crankshaft crankcase separation • remove the engine sprocket spacer 1 and two o-rings 2. • remove the oil strainer cap 3 and oil strainer (feed pump side). ( !2-14) • separate the crankcase with the special tool. " 09920-13120: crankcase separating tool note: * set the crankcas...

  • Page 162

    Transmission and crankshaft 10-5 • remove the gearshift fork shafts 4. • remove the gearshift cam 5. • remove the gearshift forks 6. • remove the countershaft assembly 7 and driveshaft assem- bly 8. Crankshaft removal • remove the crankshaft with the special tool. " 09920-13120: crankcase separating...

  • Page 163

    10-6 transmission and crankshaft transmission inspection • inspect the gear teeth, dogs, and gearshift grooves for abnor- mal wear and damage. • inspect the bushings and splines for abnormal wear and dis- coloration. • if necessary, replace defective parts with a new one. • inspect the gearshift cam...

  • Page 164

    Transmission and crankshaft 10-7 • measure the gearshift fork to groove clearance with a thick- ness gauge. • if the clearance checked is noted to exceed the limit, replace the fork or dog. # gearshift fork to groove clearance service limit: 0.50 mm (0.020 in) " 09900-20803: thickness gauge • measur...

  • Page 165

    10-8 transmission and crankshaft crankshaft inspcection • measure the crankshaft runout with v-blocks and dial gauge. Note: place the crankshaft onto the v-blocks so that it becomes hori- zontally. # crankshaft runout service limit: 0.08 mm (0.003 in) " 09900-20607: dial gauge (1/100, 10 mm) 09900-2...

  • Page 166

    Transmission and crankshaft 10-9 oil seal removal and installation • remove the oil seals ( 1, 2, 3, 4) with the special tool. " 09913-50121: oil seal remover • install each new oil seal with the special tool. " 09913-70210: bearing installer set oil seal 1, 4: $ 40 attachment oil seal 2: $ 22 attac...

  • Page 167

    10-10 transmission and crankshaft bearing removal and installation • remove the oil seals. ( !10-9) • remove the bearing retainers. Removal • remove the bearings ( 1, 3, 5, 6, 7) with the special tool. " 09913-70210: bearing installer set bearing 1, 7: $ 35 attachment bearing 3, 5, 6: $ 40 attachmen...

  • Page 168

    Transmission and crankshaft 10-11 • remove the bearing 4 with the special tools. " 09923-74511: bearing puller 09930-30104: sliding shaft • remove the bearings ( 9, 0) with the special tools. " 09921-20200: bearing remover 09930-30104: sliding shaft.

  • Page 169

    10-12 transmission and crankshaft installation • press the new bearings with the special tool. " 09913-70210: bearing installer set bearing 1: $ 52 attachment bearing 2, 8: $ 40 attachment bearing 3, 6: $ 62 attachment bearing 4: $ 32 attachment bearing 5: $ 47 attachment bearing 7: $ 42 attachment ...

  • Page 170

    Transmission and crankshaft 10-13 reed valve installation • install the reed valve 1 and reed valve guide 2 direction as shown. ' reed valve guide bolt: 4.5 n·m (0.45 kgf-m, 3.0 lb-ft) 1 reed valve 2 reed valve guide a crankcase crankshaft installation • fit the crankshaft into the left crankcase wi...

  • Page 171

    10-14 transmission and crankshaft transmission installation • apply engine oil to the following parts: driveshaft, countershaft, transmission gears, bearings. • install the driveshaft 1 and countershaft 2 with gears installed. Note: install the washers a, b located in both ends of the driveshaft pos...

  • Page 172

    Transmission and crankshaft 10-15 • install the gearshift forks 3, 4 and 5. 3 for 5th driven gear 4 for sliding dog 5 for 3rd/4th drive gear • install the gearshift cam 6 and gearshift shafts 7. Note: turn the gearshift cam to the neutral position and confirm that the driveshaft and countershaft tur...

  • Page 173

    10-16 transmission and crankshaft crankcase installation • fit the dowel pins and gasket 1. • fit the right crankcase on the left crankcase. • install the bracket a to the bolt. ( !19-24) • tighten the crankcase bolts to the specified torque. ' crankcase bolt: 11 n·m (1.1 kgf-m, 8.0 lb-ft) note: if ...

  • Page 174

    Transmission and crankshaft 10-17 primary drive gear installation • install the cam chain, cam chain tensioner and cam chain guide retainer. ( !6-24) • install the magneto rotor and key. ( !14-13) • install the gearshift linkage. ( !9-5 to -7) • install the oil pump and oil pump idle gear. ( !11-6, ...

  • Page 175

    – memo –.

  • Page 176: Lubrication System

    11 lubrication system 11-1 contents lubrication system engine lubrication system ............................................................ 11- 2 engine lubrication system chart ........................................ 11- 2 engine oil level inspection ................................................

  • Page 177: Engine Lubrication System

    11-2 lubrication system engine lubrication system engine lubrication system chart oil strainer (sca veng e pump side) oil pump (no .2) oil fil ter by-p ass oil strainer (feed pump side) crankshaft right end right crankshaft crank pin conr od big end bearing cylinder head in. & ex. Cam f a ces pist o...

  • Page 178

    Lubrication system 11-3 engine oil level inspection ( !2-11) engine oil change ( !2-12) engine oil filter change ( !2-13) oil pressure check ( !2-37) oil strainers removal ( !2-14, 10-4) oil strainers inspection ( !2-14) oil strainers installation ( !2-14, 10-15) oil seal removal • remove the right ...

  • Page 179

    11-4 lubrication system oil seal installation • install the oil seal and snap ring 1. " 09913-70210: bearing installer set oil seal: # 22 attachment 09900-06108: snap ring pliers • apply suzuki super grease to the oil seal lip. $ 99000-25010: suzuki super grease “a” (or equivalent grease) oil pump r...

  • Page 180

    Lubrication system 11-5 • remove the following parts from the oil pump. 6 oil pump no.2 outer rotor a oil pump no.1 inner rotor 7 oil pump no.2 inner rotor b pin 8 pin c oil pump cover 9 oil pump plate d oil pump driven gear shaft 0 oil pump no.1 outer rotor • remove the dowel pin. Oil pump inspecti...

  • Page 181

    11-6 lubrication system oil pump installation install the oil pump in the reverse order of removal. Pay attention to the following points: • install the oil pump cover 2 and pin 3 to the oil pump driven gear shaft 1. • fit the slot a of the oil pump no.1 inner rotor 4 to the pin 3 . • install the oi...

  • Page 182

    Lubrication system 11-7 • install the oil pump no.2 outer rotor 8. • apply engine oil to the outer rotor and inner rotor. • install the oil pump and tighten the oil pump mounting bolts to the specified torque. % oil pump mounting bolt: 6 n·m (0.6 kgf-m, 4.5 lb-ft) • install the oil pump idle gear 9,...

  • Page 183

    – memo –.

  • Page 184: Fuel System

    12 fuel system 12-1 contents fuel system fuel tank and fuel valve ............................................................... 12- 2 construction ................................................................................ 12- 2 removal ...........................................................

  • Page 185: Fuel Tank And Fuel Valve

    12-2 fuel system fuel tank and fuel valve construction removal • remove the seat and radiator covers. ( !5-2) • remove the fuel tank. ( !5-2) • drain fuel. • remove the fuel valve 1 and fuel hose 2. " warning gasoline is highly flammable and explosive. Keep heat, spark and flame away. 5 n.M (0.5 kgf...

  • Page 186

    Fuel system 12-3 cleaning and inspection if the fuel strainer is dirty with sediment, fuel will not flow smoothly and loss in engine power may result. Clean the fuel strainer with compressed air. Installation install the fuel tank and fuel valve in the reverse order of removal. Pay attention to the ...

  • Page 187: Carburetor

    12-4 fuel system carburetor construction 1 clip 2 jet needle (j.N.) 3 throttle valve 4 throttle position sensor 5 slow air jet (s.A.J) 6 starter jet 7 pilot screw 8 slow jet (s.J.) 9 main jet (m.J.) 0 float valve a float b leak jet c throttle stop screw.

  • Page 188

    Fuel system 12-5 removal • turn the fuel valve to the off position. • place a container beneath the drain hose, drain fuel from the float chamber by loosening the drain screw 1. • disconnect the fuel hose 2. • disconnect the throttle position sensor coupler 3. • remove the wire clamp and throttle pu...

  • Page 189

    12-6 fuel system disassembly • remove the hot starter valve 1 and spring from the hot starter cable. • remove the drain hose and air vent hoses. Note: do not remove the throttle position sensor 2 unless it is neces- sary to replace it. • remove the starter valve 3. • remove the top cap 4 and gasket....

  • Page 190

    Fuel system 12-7 • disassemble the throttle valve assembly. 6 throttle valve a spring 7 bearing b needle set screw 8 jet needle c floating valve 9 clip d seal 0 collar • remove the throttle shaft e with the link arm f, spring g, plastic washer h and steel washer i. Note: turn the throttle shaft e co...

  • Page 191

    12-8 fuel system • remove the drain plug o and float chamber p from the car- buretor body. • remove the and leak jet q. • remove the gasket r and o-ring s. • remove the plate form the float chamber. • pull out the push rod t of acceleration pump. • remove the e-clip, washer and acceleration pump lev...

  • Page 192

    Fuel system 12-9 • remove the float pin w. • remove the float x with the float valve y. • remove the following parts. Z main jet [ main nozzle \ buffer plate ] starter jet ^ slow jet • remove the slow air jet a..

  • Page 193

    12-10 fuel system cleaning • clean all jets with a spray-type carburetor cleaner and dry them using compressed air. • clean all passageways of the carburetor thoroughly – not just the perceived problem area. Clean the passageways in the carburetor body with a spray-type cleaner. If necessary, soak c...

  • Page 194

    Fuel system 12-11 fuel level • remove the drain hose and then install a proper cap 1 to the carburetor drain. • remove the drain screw and than connect the special tool. $ 09913-14541: fuel level gauge set • hold the carburetor in the proper angle with a stand. • fill the float chamber with fuel. • ...

  • Page 195

    12-12 fuel system float height • tilt the carburetor until the float arm b just touches the float valve rod. • measure the float height a. % standard float height: 8 mm (0.31 in) $ 09900-20101: vernier calipers (150 mm) • if necessary, slightly bend the float arm b to change the float height. • rech...

  • Page 196

    Fuel system 12-13 • fit the float chamber. • tighten the screws with the hose plates 6 and cable holder 7. • apply thread lock to the plate mounting screws and tighten them. & 99000-32050: thread lock “1342” • fit the spring 8. • install the diaphragm 9 so that the marks c face outside. • apply thin...

  • Page 197

    12-14 fuel system • apply suzuki silicone grease to the throttle shaft. ( 99000-25100: suzuki silicone grease • hook the return spring onto the stopper of the throttle pulley. • insert the throttle shaft and install the steel washer a, plastic washer b and link arm c. • fit the end of the return spr...

  • Page 198

    Fuel system 12-15 • reassemble the hot start valve e to the hot start cable end. Acceleration pump timing if turn the stop screw of the acceleration pump, adjust the accel- eration pump timing after assemble the carburetor. • select a pin b of the same diameter as the throttle valve height a and ins...

  • Page 199

    12-16 fuel system installation install the carburetor in the reverse order of removal. Pay atten- tion to the following points: • fit the projection on the carburetor body in the depression of the intake pipe. • connect the throttle pulling cable 1 and throttle returning cable 2 to the pulley. • tur...

  • Page 200: Throttle Position Sensor

    Fuel system 12-17 throttle position sensor inspection throttle position sensor input voltage • remove the right radiator cover. ( !5-2) • disconnect the throttle position sensor coupler 1. • shift the transmission into neutral. • start the engine. • measure the throttle position sensor input voltage...

  • Page 201

    12-18 fuel system removal • remove the carburetor. ( !12-5) • remove the throttle position sensor using the special tool. $ 09930-11950: torx wrench (t25) installation • with the throttle valve fully closed, install the throttle position sensor. Note: align the throttle shaft end a with the groove b...

  • Page 202: Cooling System

    13 cooling system 13-1 contents cooling system construction ...................................................................................... 13- 2 engine coolant ................................................................................... 13- 3 replacement .................................

  • Page 203: Construction

    13-2 cooling system construction 6 n.M (0.6 kgf-m, 4.5 lb-ft) 11 n.M (1.1 kgf-m, 8.0 lb-ft) 11 n.M (1.1 kgf-m, 8.0 lb-ft).

  • Page 204: Engine Coolant

    Cooling system 13-3 engine coolant replacement • open the radiator cap. • remove the drain bolt 1 and drain engine coolant. • tighten the drain bolt 1. ! Engine coolant drain bolt: 6 n·m (0.6 kgf-m, 4.5 lb-ft) • pour specified engine coolant up to the bottom of filler hole. ( "2-15) # engine coolant...

  • Page 205: Cooling Circuit

    13-4 cooling system cooling circuit inspection • remove the radiator cap. • connect the tester 1 to the filler. • give a pressure of about 120 kpa (1.2 kgf/cm 2 , 17.0 psi) and see if the system holds this pressure for 10 seconds. • if the pressure would fall during this 10-second interval, it means...

  • Page 206: Radiator

    Cooling system 13-5 radiator removal • remove the seat, radiator covers and fuel tank. ( "5-2) • drain engine coolant. ( "13-3) • remove the radiator hoses. • remove the radiator louvers 1, left and right. • remove the radiators, left and right. Inspection radiator • visually inspect the radiators a...

  • Page 207: Water Pump

    13-6 cooling system water pump removal water pump case • drain engine oil. ( "2-12) • drain engine coolant by removing the drain bolt 1. • disconnect the radiator hose 2. • remove the water pump case 3. • remove the dowel pins 4, spring 5 and oil filter 6. $ warning engine coolant may be harmful if ...

  • Page 208

    Cooling system 13-7 crankcase cover • remove the brake pedal. ( "16-18) • remove the kick starter lever. ( "8-3) • remove the right crankcase cover 1. Impeller and gear shaft • hold the water pump shaft 1 with a wrench and remove the impeller 2. • remove the washer 3 and water pump shaft 4. • remove...

  • Page 209

    13-8 cooling system oil seal • visually inspect the oil seal for damage. • if any defects are found, replace the oil seal with a new one. Installation install the water pump in the reverse order of removal. Pay attention to the following points: oil seal • apply thread lock super to the outer surfac...

  • Page 210

    Cooling system 13-9 • fit the right crankcase cover. • tighten the right crankcase cover bolts to the specified torque. ! Right crankcase cover bolt: 11 n·m (1.1 kgf-m, 8.0 lb-ft) • install the brake pedal. ( "16-18) • install the kick starter lever. ( "8-7) water pump case • install the dowel pins ...

  • Page 211

    – memo –.

  • Page 212: Electrical System

    14 electrical system 14-1 contents electrical system cautions in servicing ....................................................................... 14- 2 connector ...................................................................................... 14- 2 coupler .......................................

  • Page 213: Cautions In Servicing

    14-2 electrical system cautions in servicing connector • when connecting a connector, be sure to push it in until a click is felt. • inspect the connector for corrosion, contamination and break- age in its cover. Coupler • with a lock type coupler, be sure to release the lock when dis- connecting, a...

  • Page 214

    Electrical system 14-3 location of electrical components 1 engine stop switch 4 cdi unit 2 ignition coil/plug cap 5 pick-up coil 3 throttle position sensor 6 magneto.

  • Page 215: Construction

    14-4 electrical system construction electrical system electrical circuit wire color: g: green b/bl: black with blue tracer b/w: black with white tracer r: red b/br: black with brown tracer b/y: black with yellow tracer y: yellow b/g: black with green tracer r/w: red with white tracer b/r: black with...

  • Page 216

    Electrical system 14-5 troubleshooting no spark or poor spark step 1 1) check the ignition system couplers for poor connections. Is there connection in the ignition system couplers? Step 2 1) measure the ignition coil primary peak voltage. ( "14-9) is the peak voltage ok? Step 3 1) inspect the spark...

  • Page 217

    14-6 electrical system step 7 1) measure the exciter coil and charge coil peak voltages. ( "14-7) are the peak voltages ok? Step 8 1) check the stator. Is the stator ok? Step 9 1) measure the engine stop switch resistance. ( "14-11) is the resistance ok? Yes go to step 9. No go to step 8. Yes go to ...

  • Page 218: Ignition System

    Electrical system 14-7 ignition system ignition system peak voltage inspection • disconnect the magneto lead wire coupler 1. • connect the multi-circuit tester with peak volt adaptor as shown. • measure the highest peak voltage by depressing the kick starter lever several times forcefully. # stator ...

  • Page 219

    14-8 electrical system ignition system coil inspection • disconnect the magneto lead wire coupler 1. • measure the exciter, charge and pick-up coils resistance. # stator coil resistance # pick-up coil resistance ! 09900-25008: multi-circuit tester set & tester knob indication: resistance (Ω) if the ...

  • Page 220: Ignition Coil Primary Peak

    Electrical system 14-9 ignition coil primary peak voltage inspection • remove the seat, radiator covers and fuel tank. ( "5-2) • disconnect the ignition coil/plug cap lead wire coupler before removing the ignition coil/plug cap. • remove the ignition coil/plug cap 1. • connect a new spark plug to th...

  • Page 221

    14-10 electrical system • insert the needle pointed probe a to the lead wire coupler. Note: use the special tool (needle pointed probe), to prevent the rub- ber of the water proof coupler from damage. • measure the ignition coil primary peak voltage by depressing the kick starter lever several times...

  • Page 222

    Electrical system 14-11 engine stop switch inspection • remove the seat, radiator covers and fuel tank. ( "5-2) • disconnect the engine stop switch lead wire coupler 1. • measure the engine stop switch resistance between black/ yellow lead wire and black/white lead wire. # engine stop switch resista...

  • Page 223: Magneto Rotor

    14-12 electrical system magneto rotor removal • drain engine oil. ( "2-12) • disconnect the magneto lead wire coupler 1 and clamp. • remove the gearshift lever. ( "9-3) • remove the magneto cover 2. • remove the gasket 3 and dowel pins. • remove the magneto rotor nut 4 with the special tool. ! 09930...

  • Page 224

    Electrical system 14-13 • remove the magneto rotor with the special tool. ! 09930-35020: rotor remover • remove the magneto rotor key 5. Installation • remove any grease from the tapered portion a of the mag- neto rotor and crankshaft b. • fit the magneto rotor key 1 into the crankshaft. • install t...

  • Page 225: Stator

    14-14 electrical system • install the magneto cover 3. Note: fit the bracket to the bolt c. ( magneto cover bolt: 11 n·m (1.1 kgf-m, 8.0 lb-ft) • install the gearshift lever. ( "9-7) • pour engine oil. ( "2-12) stator removal • remove the magneto cover. ( "14-12) • remove the stator 1. • remove the ...

  • Page 226: Front And Rear Wheels

    15 front and rear wheels 15-1 contents front and rear wheels construction ...................................................................................... 15- 2 front wheel ......................................................................................... 15- 3 removal ....................

  • Page 227: Construction

    15-2 front and rear wheels construction 100 n.M (10.0 kgf-m, 72.5 lb-ft) 35 n.M (3.5 kgf-m, 25.5 lb-ft) 12 n.M (1.2 kgf-m, 8.5 lb-ft) 30 n.M (3.0 kgf-m, 21.5 lb-ft) 25 n.M (2.5 kgf-m, 18.0 lb-ft) fw d fwd.

  • Page 228: Front Wheel

    Front and rear wheels 15-3 front wheel removal • remove the front axle nut 1. • loosen the left axle holder bolts 2. • place the motorcycle on a block to lift front wheel off the ground. • loosen the right axle holder bolts 3. • remove the front axle 4. • remove the front wheel. Inspection spacer an...

  • Page 229

    15-4 front and rear wheels wheel rim • measure the wheel rim runout with the dial gauge. • if the runout exceeds the limit, replace the bearings or wheel. ! Service limit: 2.0 mm (0.08 in) ... Axial and radial " 09900-20607: dial gauge (1/100, 10 mm) 09900-20701: magnetic stand wheel bearing • turn ...

  • Page 230

    Front and rear wheels 15-5 • install the bearings with the special tool, using the suitable spacer a match for the outside dimension of bearings. " 09924-84510: bearing installer set note: * install the left side (disc side) bearing first and then the right side bearing. * after installing the beari...

  • Page 231

    15-6 front and rear wheels installation • hold the front axle shaft with the special tool and tighten the front axle nut temporarily. " 09940-34581: attachment (f) • remove the block from under the chassis tube and move the front forks up and down several times. • tighten the front axle nut to the s...

  • Page 232: Rear Wheel

    Front and rear wheels 15-7 rear wheel removal • loosen the rear axle nut 1. • place the motorcycle on a block to lift the rear wheel off the ground. • remove rear axle nut 1 and washer 2. • remove the rear axle shaft 3 and chain adjuster washers 4. • disengage the drive chain 5. • remove the rear wh...

  • Page 233

    15-8 front and rear wheels inspection wheel spacer • remove the wheel spacers from the rear wheel. • inspect the rear wheel spacers 1 and dust seals 2 for wear and cracks. • if any defects are found, replace the spacer together with the dust seal. Note: apply grease on the spacer and dust seal befor...

  • Page 234

    Front and rear wheels 15-9 • remove the bearings with the special tool. " 09921-20240: bearing remover set (remover 25 mm) • remove the spacer. • install the bearings with the special tool, using the suitable spacer a match for the outside dimension of bearings. " 09941-34513: steering race installe...

  • Page 235

    15-10 front and rear wheels • install the dust seals and apply grease to their lips. Note: when installing the dust seal, place the manufacturer’s code indicated side of the dust seal outside. " 09913-70210: bearing installer set oil seal: # 42 attachment $ 99000-25010: suzuki super grease “a” (or e...

  • Page 236

    Front and rear wheels 15-11 installation • install the rear wheel, chain adjuster washers and axle shaft. • adjust the drive chain slack. ( '2-28) • tighten the rear axle nut to the specified torque. & rear axle nut: 90 n·m (9.0 kgf-m, 65.0 lb-ft) rear wheel spokes replacement ( '19-30) fwd left rig...

  • Page 237

    – memo –.

  • Page 238: Front And Rear Brakes

    16 front and rear brakes 16-1 contents front and rear brakes construction ...................................................................................... 16- 2 brake fluid air bleeding ................................................................ 16- 3 brake fluid replacement ................

  • Page 239: Construction

    16-2 front and rear brakes construction fw d fwd fw d fwd 23 n·m (2.3 kgf-m, 16.5 lb-ft) 25 n·m (2.5 kgf-m, 18.0 lb-ft) 29 n·m (2.9 kgf-m, 21.0 lb-ft) 28 n·m (2.8 kgf-m, 20.0 lb-ft) 18 n·m (1.8 kgf-m, 13.0 lb-ft) 10 n·m (1.0 kgf-m, 7.0 lb-ft) 23 n·m (2.3 kgf-m, 16.5 lb-ft) 18 n·m (1.8 kgf-m, 13.0 lb...

  • Page 240: Brake Fluid Air Bleeding

    Front and rear brakes 16-3 brake fluid air bleeding • remove the reservoir cap. • connect a transparent tube to the bleeder valve and set the other end into a receptacle. • pour brake fluid up to the upper line. ! Specification and classification: dot 4 " warning brake fluid can be hazardous to huma...

  • Page 241: Brake Fluid Replacement

    16-4 front and rear brakes • pump the brake lever/pedal until air bubbles stop coming out from the reservoir. • hold the brake lever/pedal in the squeezed position. • open the bleeder valve and tighten the bleeder valve. • release the brake lever/pedal. • repeat this sequence until air bubbles stop ...

  • Page 242: Brake Pads Replacement

    Front and rear brakes 16-5 brake pads replacement front brake pads • remove the cap 1 and pad mounting pin 2. • remove the brake pads 3. Note: replace the two brake pads as a set. • fit the new brake pads into the caliper. • tighten the pad mounting pin to the specified torque. # brake pad mounting ...

  • Page 243: Brake Disc Inspection

    16-6 front and rear brakes brake disc inspection • inspect the brake disc for damage. • measure the front and rear brake disc thickness. % brake disc thickness service limit (front): 2.5 mm (0.10 in) (rear): 3.5 mm (0.14 in) • measure the front and rear brake disc runout. % brake disc runout service...

  • Page 244

    Front and rear brakes 16-7 front caliper removal and disassembly • place a rag under the brake hose union bolt to catch spilled brake fluid. • disconnect the brake hose. • remove the caliper mounting bolts 1. • remove the caliper. • remove the brake pads. ( $16-5) • remove the spring 2. • remove the...

  • Page 245

    16-8 front and rear brakes • remove the dust seals 7 and piston seals 8. Caliper inspection • inspect the caliper cylinder for scuffing, wear and damage. • inspect the piston for scuffing, wear and damage. • replace the defective parts with a new one. Caliper cleaning • flush the caliper ports with ...

  • Page 246

    Front and rear brakes 16-9 • tighten the caliper mounting bolts 1 to the specified torque. # brake caliper mounting bolt: 25 n·m (2.5 kgf-m, 18.0 lb-ft) • tighten the brake pad mounting pin 2 to the specified torque. # brake pad mounting pin: 18 n·m (1.8 kgf-m, 13.0 lb-ft) • set the brake hose end b...

  • Page 247

    16-10 front and rear brakes • remove the caliper bracket 4 from the caliper. • remove the boots 5 and 6. • remove the spring 7. • wrap the caliper with a rag to prevent brake fluid scatter and piston pop-out. • apply low-pressure air into the caliper through the hole to remove the piston. • remove t...

  • Page 248

    Front and rear brakes 16-11 • install the springs and boots. • apply suzuki silicone grease to the caliper axles. & 99000-25100: suzuki silicone grease • install the caliper bracket. • install the brake pads. • temporarily tighten the brake pad mounting pin. • tighten the brake pad mounting pin 1 to...

  • Page 249: Master Cylinder

    16-12 front and rear brakes master cylinder front master cylinder removal and disassembly • drain brake fluid. ( $16-4) • place a rag under the brake hose union bolt 1 to catch spilled brake fluid. • remove the union bolt 1. • disconnect the brake hose. • remove the master cylinder 2 by removing the...

  • Page 250

    Front and rear brakes 16-13 • remove the dust boot 5 and snap ring 6. ' 09900-06108: snap ring pliers • remove the washer 7 and piston/cup set 8. Master cylinder inspection • inspect the cylinder bore and piston for scuffing, wear and damage. • inspect the piston rod and spring for damage. • replace...

  • Page 251

    16-14 front and rear brakes front master cylinder reassembly and installation reassemble and install the master cylinder in the reverse order of removal and disassembly. Pay attention to the following points: • install the brake lever. ( $16-17) note: when remounting the master cylinder onto the han...

  • Page 252

    Front and rear brakes 16-15 rear master cylinder removal and disassembly • drain brake fluid. ( $16-4) • remove the cotter pin and then master cylinder rod pin 1 and washer. • remove the master cylinder 2 by removing the bolts. • place a rag under the brake hose union bolt 3 to catch spilled brake f...

  • Page 253

    16-16 front and rear brakes master cylinder inspection • inspect the cylinder bore and piston for scuffing, wear and damage. • inspect the piston rod and spring for damage. Master cylinder cleaning ( $16-13) rear master cylinder reassembly and installation reassemble and install the master cylinder ...

  • Page 254: Brake Lever

    Front and rear brakes 16-17 brake lever removal • remove the boot 1 and brake lever 2. • remove the brake lever adjuster return spring 3. ' 09930-11950: torx wrench (t25) installation install the brake lever in the reverse order of removal. Pay atten- tion to the following points: • apply grease to ...

  • Page 255: Brake Pedal

    16-18 front and rear brakes brake pedal removal • remove the clip 1. • remove the cotter pin 2 and washer 3. • remove the master cylinder rod pin 4. • remove the brake pedal pivot bolt 5 and return spring 6. Installation • apply suzuki super grease to the oil seals and brake pedal pivot bolt. ( 9900...

  • Page 256: Front Fork and Steering

    17 front fork and steering 17-1 contents front fork and steering construction ...................................................................................... 17- 2 front fork, steering ................................................................. 17- 2 handlebar controls ....................

  • Page 257: Construction

    17-2 front fork and steering construction front fork, steering 23 n.M (2.3 kgf-m, 16.5 lb-ft) 70 n.M (7.0 kgf-m, 51.0 lb-ft) 18 n.M (1.8 kgf-m, 13.0 lb-ft) 22 n.M (2.2 kgf-m, 16.0 lb-ft) 30 n.M (3.0 kgf-m, 21.5 lb-ft) 35 n.M (3.5 kgf-m, 25.5 lb-ft) 23 n.M (2.3 kgf-m, 16.5 lb-ft) 45 n.M (4.5 kgf-m, 3...

  • Page 258

    Front fork and steering 17-3 handlebar controls 6 n·m (0.6 kgf-m, 4.5 lb-ft) 6 n·m (0.6 kgf-m, 4.5 lb-ft) 25 n·m (2.5 kgf-m, 18.0 lb-ft) apply handle grip bond. Apply handle grip bond..

  • Page 259

    17-4 front fork and steering removal • place the motorcycle on a block to lift front wheel off the ground. • remove the front wheel. ( !15-3) • remove the front number plate 1. • remove the protector 2. • remove the handlebars. Note: mark the paint mark a to the matching surface of handlebar holder ...

  • Page 260

    Front fork and steering 17-5 disassembly • set rebound and compression damper settings to the mini- mum settings (softest) before disassembling. Record the set- ting before turning the adjuster. • thoroughly clean the fork before disassembly. • clamp the outer tube with a vise. Protect the outer tub...

  • Page 261

    17-6 front fork and steering • clamp the axle holder 2 with a vise. Protect the axle holder with a rag when using a vise. • loosen the center bolt 3 completely with a 21 mm socket wrench. • compress the outer tube by hands and install the conrod holder (special tool) between the axle holder bottom 2...

  • Page 262

    Front fork and steering 17-7 • with the outer tube compressed by hands, remove the special tool. • loosen the fork cap bolt 1 (sub-tank) and remove the sub- tank 6 along with the damper rod assembly 7. • remove the fork spring 8. • remove the dust seal 9. • remove the stopper ring 0. Caution removin...

  • Page 263

    17-8 front fork and steering inner tube • separate the inner tube 1 out of the outer tube 2. • remove the slide bushing 3 from the inner tube 1. • remove the following parts from the inner tube 1. Guide bushing 4 seal retainer 5 oil seal 6 stopper ring 7 dust seal 8 danper rod and compression damper...

  • Page 264

    Front fork and steering 17-9 • drain the fork oil from the damper rod assembly by moving the inner rod several strokes. Inspection center bolt • inspect the adjuster rod of the center bolt for damage. If it is damaged, replace it with a new one. Compression damper unit • inspect the compression damp...

  • Page 265

    17-10 front fork and steering damper rod assembly • inspect the damper rod assembly for scratches or bending. If it has scratches or is bent, replace it with a new one. Fork spring • measure the free length of front fork spring. • if it is shorter than service limit, replace it with a new one. $ ser...

  • Page 266

    Front fork and steering 17-11 reassembly inner tube • apply fork oil to the oil seal lip and the dust seal. • cover the inner tube with a plastic film. • install the following parts to the inner tube: new dust seal 1 stopper ring 2 new oil seal 3 note: the side of the oil seal that has a mark should...

  • Page 267

    17-12 front fork and steering • attach the dust seal 4. Note: after attaching the dust seal, make sure that there are no cracks around the circumference of the seal. Cracks could allow water, mud and the like to enter and cause an oil leak. Damper rod and compression damper unit • clean each threade...

  • Page 268

    Front fork and steering 17-13 • hold the bottom (flat part) of the sub-tank. • tighten the compression damper unit 5 to the specified torque. & compression damper unit: 30 n·m (3.0 kgf-m, 21.5 lb-ft) • with the damper rod held in vertical position, slowly move the inner rod several strokes. • tighte...

  • Page 269

    17-14 front fork and steering • with the damper rod in horizontal position, move the inner rod by hand to inspect it if operating smoothly. • if the inner rod is not extend, repeat the “compression damper unit” procedures (pour the specified amount fork oil and discharge an excess of oil). ( !17-12)...

  • Page 270

    Front fork and steering 17-15 • clamp the axle holder with a vise. Protect the axle holder with a rag when using a vise. • compress the outer tube by hands and install the conrod holder (special tool) between the axle holder bottom and lock- nut. " 09910-20115: conrod holder • insert the push rod in...

  • Page 271

    17-16 front fork and steering • tighten the center bolt to the specified torque. & center bolt: 70 n·m (7.0 kgf-m, 50.5 lb-ft) • loosen and remove the fork cap bolt (sub-tank) from the outer tube and slowly slide down the outer tube. " 09941-53630: front fork top cap wrench • pour the specified amou...

  • Page 272

    Front fork and steering 17-17 installation • install the front fork with the line t aligned with the upper sur- face of the upper bracket. • check that the air valve a is positioned at the front. • tighten the fork lower clamp bolts to the specified torque. & fork lower clamp bolt: 23 n·m (2.3 kgf-m...

  • Page 273: Steering

    17-18 front fork and steering steering removal handlebars • place the motorcycle on a block to lift front wheel off the ground. • remove the front number plate and protector. ( !17-4) • remove the clamps. • remove the engine stop switch 1. • remove the clutch lever holder. Note: mark the paint marks...

  • Page 274

    Front fork and steering 17-19 • remove the handlebar holder bolts and remove the handle- bars. Note: mark the paint mark to the matching surface of handlebar holder and handlebars before removing. Steering stem • remove the front wheel 1. ( !15-3) • remove the brake hose guide. • remove the front fo...

  • Page 275

    17-20 front fork and steering • remove the handlebar holders, damper bushings and spac- ers. • remove the steering stem nut with the special tools. Note: hold the steering stem lower bracket to prevent it from falling. " 09940-14911: steering nut socket wrench 09940-14960: steering nut wrench socket...

  • Page 276

    Front fork and steering 17-21 bearing replacement • remove the lower bearing. • fit the lower bearing with the special tool. " 09925-18011: steering bearing installer note: replace the outer race and bearing as a set. • remove the upper outer race with the special tools. " 09941-54911: bearing outer...

  • Page 277

    17-22 front fork and steering installation install the steering in the reverse order of steering removal. Pay attention to the following points: steering stem • apply grease to the bearings. ( 99000-25010: suzuki super grease “a” (or equivalent grease) • fit the steering stem lower bracket, upper be...

  • Page 278

    Front fork and steering 17-23 • temporarily install the front forks to the steering stem and tighten the lower clamp bolts. • tighten the steering stem head nut to the specified torque. & steering stem head nut: 100 n·m (10.0 kgf-m, 72.5 lb-ft) • install the front fender as shown. • remount the fron...

  • Page 279

    17-24 front fork and steering • tighten the handlebar holder set nuts to the specified torque. & handlebar holder set nut: 44 n·m (4.4 kgf-m, 32.0 lb-ft) • apply grease to the throttle cable and their hole. ( 99000-25010: suzuki super grease “a” (or equivalent grease) • align the matching mark d on ...

  • Page 280

    Front fork and steering 17-25 handlebars • apply handle grip bond to the left handlebar end and inside of the left grip. • align the “ ” mark on the left grip with the matching mark a on the left handlebar end. Apply handle grip bond. Apply handle grip bond..

  • Page 281

    17-26 front fork and steering • align the matching mark b on the handlebars with the clutch lever holder matching surface. • tighten the upper bolt first temporarily to provide clearance on the lower side and then tighten both the bolts. • install the engine stop switch and clamps. • install the fro...

  • Page 282: Rear Suspension

    18 rear suspension 18-1 contents rear suspension construction ...................................................................................... 18- 2 rear suspension .......................................................................... 18- 2 rear shock absorber ...............................

  • Page 283: Construction

    18-2 rear suspension construction rear suspension 60 n.M (6.0 kgf-m, 43.5 lb-ft) 80 n.M (8.0 kgf-m, 58.0 lb-ft) 80 n.M (8.0 kgf-m, 58.0 lb-ft) 80 n.M (8.0 kgf-m, 58.0 lb-ft) 60 n.M (6.0 kgf-m, 43.5 lb-ft) 70 n.M (7.0 kgf-m, 50.5 lb-ft).

  • Page 284: Rear Shock Absorber

    Rear suspension 18-3 rear shock absorber removal • place a block under chassis tube. • remove the seat. ( !5-2) • loosen the air cleaner clamp screw. • remove the right frame cover and muffler 1. ( !5-2, -3) • remove the seat rail assembly 2. • remove the rear shock absorber upper mounting bolt and ...

  • Page 285

    18-4 rear suspension • remove the rear shock absorber lower mounting bolt and nut. Note: if necessary, move the swingarm up or down to facilitate this mounting bolt/nut removal. • remove the rear shock absorber. Spring replacement • loosen the lock-nut 1 with the special tool and turn it fully to th...

  • Page 286

    Rear suspension 18-5 • adjust the spring set length and tighten the lock-nut. # standard spring set length: 5.6 mm (0.22 in) compressed from the free length spring set length adjustable range: 247 – 263 mm (9.72 – 10.35 in) [at spring free length 265 mm (10.43 in)] a: hardest spring setting b: softe...

  • Page 287

    18-6 rear suspension bearing replacement • remove the spacers. • remove the needle roller bearings 1. (26 pieces of needle roller bearing) • remove the dust seals 2. • remove the needle roller bearing cage 3 with the special tool. " 09921-20240: bearing remover set (remover 17 mm) • press the new ne...

  • Page 288

    Rear suspension 18-7 oil replacement tools and equipment • following tools and equipment are required to perform oil replacement. 1 screwdriver or small punch 7 rags 2 vise* 8 nitrogen tank 3 drain pan 9 filler hose and nozzle 4 oil can 0 regulator assembly 5 beaker a owner’s service manual 6 specif...

  • Page 289

    18-8 rear suspension • remove the compression adjuster assembly 1 from the rear shock absorber. • place a drain pan under the rear shock absorber unit. • move the rod and drain the oil completely. • push the valve core again to equalize the bladder to atmo- spheric pressure. • pour the fresh specifi...

  • Page 290

    Rear suspension 18-9 • replace the o-rings on the compression adjuster assembly with new ones. • reinstall the compression adjuster assembly 1. $ compression adjuster assembly: 30 n·m (3.0 kgf-m, 21.5 lb-ft) • fill the rear shock absorber unit with nitrogen gas to 784 kpa (8.0 kgf/cm 2 , 113.8 psi)....

  • Page 291

    18-10 rear suspension disassembly and inspection • clean and dry the rear shock absorber. • remove the spring from the rear shock absorber. ( !18-4) • turn the rebound damping force adjuster to the softest posi- tion. • press the valve with a screwdriver to bleed out nitrogen gas. ( !18-7) • remove ...

  • Page 292

    Rear suspension 18-11 • extract the damper rod assembly from the shock absorber body. • inspect the oil seal and o-rings. • inspect the damper rod for bends and scratches. • inspect the inner surface of the body. • inspect the “teflon coating metal” on the piston. • replace the o-rings with new ones...

  • Page 293

    18-12 rear suspension installation install the rear shock absorber in the reverse order of removal. Pay attention to the following points: • tighten the rear shock absorber lower mounting bolt and nut to the specified torque. Note: if necessary, move the swingarm up or down to facilitate this mounti...

  • Page 294: Swingarm

    Rear suspension 18-13 swingarm removal • place the motorcycle on a block to lift rear wheel off the ground. • remove the rear wheel. ( !15-7) • remove the chain guide. • remove the rear brake hose guide. • remove the rear brake caliper from the swingarm. • remove the cushion rod bolt and nut. • remo...

  • Page 295

    18-14 rear suspension • down the rear brake pedal, remove the pivot shaft. • remove the swingarm. • remove the chain buffer. • remove the plates. • remove the following parts from the swingarm. Spacer 1 oil seal 2 washer 3 thrust bearing 4 dust seal 5 spacer 6.

  • Page 296

    Rear suspension 18-15 inspection pivot shaft • measure the pivot shaft runout with the dial gauge and v-blocks. • if any the runout exceeds the limit, replace the pivot shaft with a new one. # swingarm pivot shaft runout service limit: 0.3 mm (0.01 in) " 09900-20607: dial gauge (1/100, 10 mm) 09900-...

  • Page 297

    18-16 rear suspension bearing, spacer, dust seal, oil seal • inspect the bearings, spacers, dust seals and oil seals for damage. • replace the defective parts with a new one. • insert the spacer into the bearings and inspect them for play and smooth movement. • if excessive play is noted, replace th...

  • Page 298

    Rear suspension 18-17 installation install the swingarm in the reverse order of removal. Pay atten- tion to the following points: • install the following parts into the swingarm. 1 oil seal 5 washer 2 spacer 6 dust seal 3 washer 7 spacer 4 thrust bearing • apply grease to the dust seals, bearings an...

  • Page 299: Rear Suspension Linkage

    18-18 rear suspension rear suspension linkage removal • place a block under the chassis tubes. • remove the lower drive chain control roller 1. • remove the rear cushion rod bolt and nut. • remove the cushion lever bolt and nut. • remove the shock absorber lower bolt and nut. • remove the collars, o...

  • Page 300

    Rear suspension 18-19 inspection • inspect the cushion rod and cushion lever for damage. • inspect the dust seals, oil seals and spacers for damage. • replace the defective parts with a new one. • insert the spacers into the bearings and inspect them for excessive play and smooth movement. • if exce...

  • Page 301

    18-20 rear suspension bearing replacement • remove the collars, spacers and dust seals. ( !18-18) • remove the needle roller bearings. Cushion rod bearing (one side 32 pieces of needle roller bearing) cushion lever bearing a (33 pieces of needle roller bearing) b (one side 32 pieces of needle roller...

  • Page 302

    Rear suspension 18-21 installation install the rear suspension linkage in the reverse order of removal. Pay attention to the following points: • position the dust seals 1 so that the manufacturer’s code indicated side of the seals face outside. ( 2: inside) • apply grease to the dust seals. % 99000-...

  • Page 303

    18-22 rear suspension • tighten the cushion lever, cushion rod and swingarm nuts to the specified torque. $ tightening torque: a: 60 n·m (6.0 kgf-m, 43.5 lb-ft) b: 60 n·m (6.0 kgf-m, 43.5 lb-ft) c: 80 n·m (8.0 kgf-m, 58.0 lb-ft) d: 80 n·m (8.0 kgf-m, 58.0 lb-ft) e: 80 n·m (8.0 kgf-m, 58.0 lb-ft) f: ...

  • Page 304

    Rear suspension 18-23 • tighten the lower drive chain control roller nut to the specified torque. $ chain roller nut: 22 n·m (2.2 kgf-m, 16.0 lb-ft) caution improperly reassembled rear suspension linkage bolts can interfere with suspension move- ment and damage the rear suspension linkage. * make su...

  • Page 305

    – memo –.

  • Page 306: Servicing Information

    19 servicing information 19-1 contents servicing information service data ......................................................................................... 19- 2 tightening torque ............................................................................. 19-10 special tools .................

  • Page 307: Service Data

    19-2 servicing information service data valve + guide unit: mm (in) item standard limit valve diam. In. 31 (1.22) — ex. 25 (0.98) — valve clearance (when cold) in. 0.09 – 0.16 (0.004 – 0.006) — ex. 0.17 – 0.24 (0.006 – 0.009) — valve guide to valve stem clearance in. 0.010 – 0.037 (0.0004 – 0.0015) ...

  • Page 308

    Servicing information 19-3 camshaft + cylinder head unit: mm (in) cylinder + piston + piston ring unit: mm (in) item standard limit cam height in. 34.86 – 34.91 (1.372 – 1.374) 34.56 (1.361) ex. 34.38 – 34.43 (1.354 – 1.356) 34.08 (1.342) camshaft journal oil clearance in. & ex. 0.023 – 0.066 (0.001...

  • Page 309

    19-4 servicing information conrod + crankshaft unit: mm (in) oil pump clutch unit: mm (in) radiator + engine coolant item standard limit conrod small end i.D. 16.010 – 16.018 (0.6303 – 0.6306) 16.040 (0.6315) conrod deflection — 3.0 (0.12) conrod big end side clearance 0.20 – 0.65 (0.008 – 0.026) 1....

  • Page 310

    Servicing information 19-5 transmission + drive chain unit: mm (in) except ratio carburetor item standard limit primary reduction ratio 3.210 (61/19) — final reduction ratio 4.000 (48/12) — gear ratios low 2.153 (28/13) — 2nd 1.764 (30/17) — 3rd 1.470 (25/17) — 4th 1.238 (26/21) — top 1.090 (24/22) ...

  • Page 311

    19-6 servicing information electrical unit: mm (in) brake + wheel unit: mm (in) item specification note ignition timing 18° b.T.D.C. At 2 100 r/min. Spark plug type ngk: cr8eia-10 gap 0.9 – 1.0 (0.035 – 0.039) spark performance over 8 (0.3) at 1 atm. Pick-up coil resistance 72 – 127 Ω r – g exciter ...

  • Page 312

    Servicing information 19-7 tire item standard limit brake caliper cylinder bore front 27.000 – 27.050 (1.0630 – 1.0650) — rear 25.400 – 25.450 (1.0000 – 1.0020) — brake caliper piston diam. Front 26.900 – 26.950 (1.0591 – 1.0610) — rear 25.335 – 25.368 (0.9974 – 0.9987) — brake fluid type dot 4 — wh...

  • Page 313

    19-8 servicing information suspension unit: mm (in) item standard limit note front fork stroke 310 (12.2) — front fork inner tube o.D. 47 (18.5) — front fork spring free length 494 ± 2.5 (19.45 ± 0.10) 487 (19.17) front fork damping force adjuster rebound max – 14 clicks turn back — compres- sion ma...

  • Page 314

    Servicing information 19-9 fuel + oil item specification note fuel type use only unleaded gasoline of at least 90 pump octane (r/2 + m/2 method). E-03, 28 use only unleaded gasoline of at least 95 octane. (research method) the others fuel tank capacity 7.0 l (1.8/1.5 us/imp gal) engine oil type sae ...

  • Page 315: Tightening Torque

    19-10 servicing information tightening torque engine part n·m kgf-m lb-ft cylinder head cover bolt 14 1.4 10.0 spark plug 11 1.1 8.0 cylinder head bolt (initial) 25 2.5 18.0 (final) 50 5.0 36.0 cylinder head base nut 10 1.0 7.0 cylinder base bolt 12 1.2 8.5 camshaft journal holder bolt 10 1.0 7.0 pr...

  • Page 316

    Servicing information 19-11 part n·m kgf-m lb-ft engine mounting nut (upper) 45 4.5 32.5 engine mounting nut (lower) 55 5.5 40.0 engine mounting nut (front) 60 6.0 43.5 engine mounting bracket nut (upper) 40 4.0 29.0 engine mounting bracket nut (front) 40 4.0 29.0 engine sprocket cover bolt 11 1.1 8...

  • Page 317

    19-12 servicing information chassis part n·m kgf-m lb-ft handlebar clamp bolt 25 2.5 18.0 handlebar holder set nut 44 4.4 32.0 front fork upper clamp bolt (right and left) 23 2.3 16.5 front fork lower clamp bolt (right and left) 23 2.3 16.5 steering stem head nut 100 10.0 72.5 front fork cap bolt 35...

  • Page 318

    Servicing information 19-13 for other bolts and nuts not listed in the table, refer to this chart. Bolt diameter (mm) conventional or “4” marked bolt “7” marked or crown headed bolt n·m kgf-m lb-ft n·m kgf-m lb-ft 4 1.5 0.15 1.0 2.3 0.23 1.5 5 3 0.3 2.0 4.5 0.45 3.0 6 5.5 0.55 4.0 10 1.0 7.0 8 13 1....

  • Page 319: Special Tools

    19-14 servicing information special tools 09900-06107 snap ring pliers 09900-06108 snap ring pliers 09900-20101 vernier calipers (150 mm) 09900-20202 micrometer (25 – 50 mm) 09900-20204 micrometer (75 – 100 mm) 09900-20205 micrometer (0 – 25 mm) 09900-20530 cylinder gauge set 09900-20602 dial gauge ...

  • Page 320

    Servicing information 19-15 09913-50121 oil seal remover 09913-70210 bearing installer set 09915-64512 compression gauge 09915-74511 oil pressure gauge 09916-10911 valve lapper set 09916-14510 valve lifter 09916-14521 attachment 09916-14530 attachment 09916-34542 reamer handle 09916-33210 valve guid...

  • Page 321

    19-16 servicing information 09930-30104 slide shaft 09930-35020 rotor remover 09930-44560 rotor holder 09940-14911 steering nut socket wrench 09940-14960 steering nut wrench socket 09940-34581 attachment (f) 09940-40211 adapter 09940-52861 front fork oil seal installer set 09941-34513 steering race ...

  • Page 322: Wiring Diagram

    Servicing information 19-17 wiring diagram wire color b: black bl: blue g: green r: red y: yellow b/bl: black with blue tracer b/br: black with brown tracer b/g: black with green tracer b/r: black with red tracer b/w: black with white tracer b/y: black with yellow tracer r/w: red with white tracer w...

  • Page 323: Cable Routing

    19-18 servicing information cable routing connect the throttle cab le to the rear side on throttle case . P a ss through the cab les in the guide . Clamp mar king (pulling side only) connect the throttle cab le to the front side on throttle case . 3 0 – 4 0 m m (1 .2 – 1 .6 in ) engine stop s w itch...

  • Page 324

    Servicing information 19-19 p a ss through the hot star ter cab le betw een fr ame br idge and flame , then through betw een r adiator and fr ame , and through outside o v erflo w pipe . P a ss through the clutch cab le into the br ac k e t. P a ss through the lead behind the engine mounting plate ....

  • Page 325: Wiring Harness Routing

    19-20 servicing information wiring harness routing clamp engine stop s w itch lead wire 20 – 30 mm (0.8 – 1.2 in) white paint to magneto handlebars fr ont engine stop s w itch lead wire clamp wir ing har ness engine stop s w itch lead wire tighten the g round ter m inal on the cdi br ac k e t. Do no...

  • Page 326: Fuel Hose Routing

    Servicing information 19-21 fuel hose routing 11 n.M (1.1 kgf-m, 8.0 lb-ft) : the ends of the clamp should face..... Forward. Pass through the fuel hose above the hot starter cable and starter knob..

  • Page 327

    19-22 servicing information fuel tank cushion installation clean an adhesive surface before adhering the cushion. 0.3 mm (0.012 in) 130 mm (5.1 in) 250 mm (9.8 in).

  • Page 328: Radiator Hose Routing

    Servicing information 19-23 radiator hose routing water pump installation : the clamp screw head should face..... Hose clamp screw tightening torque: 2.3 n·m (0.23 kgf-m, 1.65 lb-ft) forward left side. Backward. Backward right side. Forward right side. Backward right side. Backward. Forward right si...

  • Page 329

    19-24 servicing information crankcase and cover installation 11 n.M (1.1 kgf-m, 8.0 lb-ft) 90˚ 21 n.M (2.1 kgf-m, 15.0 lb-ft) 14 n.M (1.4 kgf-m, 10.0 lb-ft) 11 n.M (1.1 kgf-m, 8.0 lb-ft) 11 n.M (1.1 kgf-m, 8.0 lb-ft) 11 n.M (1.1 kgf-m, 8.0 lb-ft) 6 n.M (0.6 kgf-m, 4.5 lb-ft) 6 n.M (0.6 kgf-m, 4.5 lb...

  • Page 330: Magneto Installation

    Servicing information 19-25 magneto installation pass through the lead wire between stator mount boss and mount rib. Do not pinch the lead wire between stator and magneto cover. 10 n.M (1.0 kgf-m, 7.0 lb-ft) 4.5 n.M (0.45 kgf-m, 3.25 lb-ft) 80 n.M (8.0 kgf-m, 58.0 lb-ft).

  • Page 331: Front Brake Hose Routing

    19-26 servicing information front brake hose routing set the brake hose end between the hose stopper, then tighten the brake hose union bolt to the specified torque. Front brake hose clamp front fork protector after touching the brake hose union to the stopper, tighten the union bolt to the specifie...

  • Page 332: Rear Brake Hose Routing

    Servicing information 19-27 rear brake hose routing stopper hose guide set the br ak e hose end betw een the hose stopper , then tighten the br ak e hose union bolt to the specified torque . Rear br ak e caliper outside hose guide rear br ak e master cylinder set the br ak e hose end betw een the ho...

  • Page 333: Rear Brake Pedal Set-Up

    19-28 servicing information rear brake pedal set-up front number plate installation sect a a a a 0 – 10 mm (0.0 – 0.4 in) view a a number plate band handlebar hot starter cable clutch cable number plate band.

  • Page 334: Handlebar Set-Up

    Servicing information 19-29 handlebar set-up assemble throttle cables as to show this drawing. Throttle cable (pull side) 2.2 mm (0.087 in) 55˚ 30˚ 105˚ 66˚ a view a marking on drawing position. Match slit of throttle case with marking. Apply adhesive to inner of grip and handlebars. Marking on draw...

  • Page 335: Clutch Cable Adjuster

    19-30 servicing information clutch cable adjuster rear wheel spokes installation adjustable range do not apply grease to the rubber covers. Fit the cover positively. Adjuster tur urn to loosen n to loosen the clutch cab the clutch cable tension. Le tension. Turn to loosen the clutch cable tension. T...

  • Page 336: Rim Lock Installation

    Servicing information 19-31 exhaust pipe and muffler installation rim lock installation 23 n.M (2.3 kgf-m, 16.5 lb-ft) 21 n.M 2.1 kgf-m, 15.0 lb-ft 11 n.M (1.1 kgf-m, 8.0 lb-ft) 0 – 2 mm (0.00 – 0.08 in) 23 n.M (2.3 kgf-m, 16.5 lb-ft) rotational direction 40˚ rim lock for 1.85 rim.

  • Page 337: Front Fender  Installation

    19-32 servicing information front fender installation rear fender installation.

  • Page 338: Frame Cover Installation

    Servicing information 19-33 frame cover installation frame cover cushion installation double-faced tape.

  • Page 339: Specifications

    19-34 servicing information specifications dimensions and dry mass overall length ....................................................... 2 165 mm (85.2 in) overall width ........................................................ 830 mm (32.7 in) overall height ...........................................

  • Page 340

    Servicing information 19-35 chassis front suspension ................................................. Upside-down telescopic fork rear suspension ................................................. Swingarm type front suspension stroke ...................................... 310 mm (12.2 in) rear whee...

  • Page 341: Spare Parts List

    19-36 servicing information spare parts list optional parts carburetor: !4-2 front fork spring: !4-14 rear suspension spring: !4-19 item part name part number q’ty 1 parts set, spare 19900-10h00 1 1 gasket, magneto cover 11483-10h00 1 2 gasket, clutch cover outer 11484-10h00 1 3 gasket, exhaust, pip...

  • Page 342: Setting Data

    Servicing information 19-37 setting data *make copies. Date / / / / / / race/course / / / temp./humidity / / / weather course coudition main jet jet needle / / / slow jet air screw float level spark plug oil level mm mm mm comp. Adj. Position re-bound adj. Position spring spring spring set length mm...

  • Page 343

    – memo –.

  • Page 344

    Printed in japan 300 takatsuka, hamamatsu, japan k7 failure to follow these safety precautions may increase your risk of injury: ! Wear a helmet, eye protection, and bright protective clothing. ! Don’t ride after consuming alcohol or other drugs. ! This owner’s service manual contains important safe...