1. DL manuals
  2. SVP
  3. Transmitter
  4. HDT-02_H.264
  5. User Manual

SVP HDT-02_H.264 User Manual

Manual is about: HIGH DEFINITION DIGITAL MULTIBAND- MULTIFUNCTION TRANSMITTER

Summary of HDT-02_H.264

  • Page 1

    Svp broadcast microwave hdt-02_h.264 high definition digital multiband - multifunction transmitter user manual v4.11 accessories included in this manual: pa-5 pa-10 av-x03f antenna gps-02 antenna rtc-01 remote control.

  • Page 2

    I hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 contents chapter 1: introduction this first chapter provides a general description of the high definition hdt- 02_h.264 camera transmitter. Chapter 2: technical features this second part offers transmitter physical and env...

  • Page 3

    Ii hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 dear customer, we would like to thank you for selecting this equipment and welcome you to the svp’s products user’s growing family. We are sure that the addition of this equipment to your existing installation will cause ...

  • Page 4

    Iii hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 about this manual this user’s guide provides indications and explanations about how to easily set up the hdt-02 transmitter for the most common use cases. This document is intended to help first time users: - find their ...

  • Page 5

    Iv hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 important notes 1. The hdt-02_h.264 high definition camera transmitter is completely compatible with the dvb-t/t2/s2 standards, included in the european standard etsi en300744 (dvb-t), etsi en300755 (dvb-t2), etsi en30230...

  • Page 6

    V hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 safe operating procedures in this section there are shown safety requirements so as to ensure awareness of potential hazard to the personnel operating and maintaining the equipment. Fcc this chapter has been done taking in...

  • Page 7

    Vi hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 1. Hdt-02 transmitter with avf antenna (3 dbi) g = 2 p max = 100 mw eirp = 200 mw r min = 4 cm = 1.57 in 2. Hdt-02 transmitter + pa-5 (5 w) with avf antenna g = 2 p max = 5000 mw eirp = 10000 mw r min = 28.2 cm = 11.1 in ...

  • Page 8

    Vii hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 declaration of rf exposure compliance for exemption from routine evaluation limits sar evaluation – avf-203l antenna as shown in the point number 2.5.1 from the rss-102 radio standard specification, sar evaluation is not...

  • Page 9

    Viii hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 sar evaluation – avf-203lb antenna as shown in the point number 2.5.1 from the rss-102 radio standard specification, sar evaluation is not required if the separation distance between the user and the radiating element o...

  • Page 10

    Ix hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 rf exposure evaluation as shown in the point number 2.5.2 from the rss-102 radio standard specification, rf exposure evaluation is required if the separation distance between the user and the device’s radiating element is...

  • Page 11

    X hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 first aid in case of electric shock do not touch the victim with your bare hands until the circuit is broken. Switch off. If this is not possible, protect yourself with dry insulating material and pull the victim clear of ...

  • Page 12

    Xi hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 8. In the case of severe facial injuries it may be necessary to do a manual method of artificial respiration (silvester-brosch or holger nielsen). Briefly, these methods apply compression to ribcage with the victim lying ...

  • Page 13

    1 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 main index chapter 1: introduction ................................................................... 5 chapter 2: technical features ....................................................... 10 chapter 3: transmitter opera...

  • Page 14

    2 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.4 dvb-t useful bitrate ............................................... 72 3.5.2.3.5 dvb-s2 ................................................................. 74 3.5.2.3.6 symbol rate calculation .......................

  • Page 15

    3 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 6.2 application example .............................................................. 116 chapter 7: equipment installation ............................................... 117 7.1 introduction ...............................

  • Page 16

    4 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.3 dvb-s ...................................................................................... 160 d.3.1 how does it works ............................................................... 160 d.4 dvb-s2 .....................

  • Page 17: Chapter 1: Introduction

    5 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 1: introduction the hdt-02 is the new multifunction and multiband transmitter developed by svp broadcast microwave. The features of this equipment, achievable only by svp, make this transmitter the most advanced in...

  • Page 18

    6 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 features input video signals, composite video, 3g –sdi, hd-sdi, sd-sdi or hdmi are mpeg-4 encoded, together with 4 analogue audios, 2 stereo aes/ebu channels, hdmi embedded or 4 digital audios embedded on the sdi signal. T...

  • Page 19

    7 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 an ofdm modulated signal, since uses a low symbol rate modulation scheme (i.E. Where the symbols are relatively long compared to the channel time characteristics) suffer less from intersymbol interference caused by multipa...

  • Page 20

    8 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 dvb-t features the rf stage of the hdt-02 transmitter is the same as the dvb-t2 one. The difference is found in the modulation part as is commented bellow. The hdt-02 digital camera transmitter uses cofdm (coded orthogonal...

  • Page 21

    9 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 dvb-s features in case the hdt-02 transmitter is needed to be used as a satellite transmitter, it features an if stage in the l band with an output power level from -20 to +5 dbm and a l band output that provides a 10 mhz ...

  • Page 22

    10 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 2: technical features rf stage dvb-t2 and dvb-t frequency band: 1 to 6.4 ghz max. Output power: 100 mw (selectable from -5 to +20 dbm) if stage dvb-s2 and dvb-s frequency band: l band output power level: -20 to +5...

  • Page 23

    11 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 audio: input: sdi embedded / hdmi embedded aes digital / analogue analogue: 2 stereo / 4 mono line,micro dynamic and micro with phantom sdi embedded: 1 group (4 audio channels) aes/ebu: 2 stereo channels user data data ch...

  • Page 24

    12 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 encryption biss: biss-1 and biss-e modulation dvb-t2: cofdm 1k,2k,4k, 8k,8k.Ext qpsk, 16 qam, 64 qam, 256 qam constellation rotation ldpc fec: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6 ig: 1/4, 19/128, 1/8, 19/256, 1/16, 1/32 1/128 ba...

  • Page 25

    13 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 power supply dc input: 8 to 36 v and by batteries anton-bauer or v consumption: 16 watt. (12v) 20 watt. (28v) mechanical size: 124 x 45 x 193 mm 4.9x1.8x7.6 in weight: 1 kg (without fastenings) 2.2 lb environmental aerona...

  • Page 26

    14 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 3: transmitter operation and menus this third chapter provides the user with all necessary information to control, configure and operate the equipment properly. 3.1 display to turn the equipment on and off, press ...

  • Page 27

    15 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 once an option has been selected, the main screen appears where these parameters are displayed:  frequency (mhz).  transmission standard (dvb-t2, dvb-t, dvb-s2,dvb-s)  output power (dbm): 3 options available: - variabl...

  • Page 28

    16 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 next there are shown the linkages between the input and the character displayed in the principal screen: video cvbs c hdmi h sdi s asi a test pattern g audio embedded e aes/ebu u analogue a test tone g data rs232 d gps g ...

  • Page 29

    17 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.1.1 main screen for the dvb-t2 in the table below, it is explained the function of each parameter. These values are numbered in the order they appear in the main screen. Parameter nº function 1 transmission frequency (m...

  • Page 30

    18 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 11 video format (1080p, 1080i, 720p, 576i, 480i) 12 video options:  profile (mpeg-4 4:2:0 or mpeg-4 4:2:2)  delay (standard (s), low delay (l), super low delay (sl) or ultra low delay (ul)) table 3.2 main screen for dvb...

  • Page 31

    19 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.1.2 main screen for the dvb-t in the table below, it is explained the function of each parameter. These values are numbered in the order they appear in the main screen. Parameter nº function 1 transmission frequency (mh...

  • Page 32

    20 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 11 video format (1080p, 1080i, 720p, 576i, 480i) 12 video options:  profile (mpeg-4 4:2:0 or mpeg-4 4:2:2)  delay (standard (s), low delay (l), super low delay (sl) or ultra low delay (ul)) table 3.3 main screen for dvb...

  • Page 33

    21 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.1.3 main screen for the dvb-s2 in the table below, it is explained the function of each parameter. These values are numbered in the order they appear in the main screen. Parameter nº function 1 transmission frequency (m...

  • Page 34

    22 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 11 video options:  profile (mpeg-4 4:2:0 or mpeg-4 4:2:2)  delay (standard (s), low delay (l), super low delay (sl) or ultra low delay (ul)) table 3.4 main screen for dvb-s2 standard figure 3.4 main screen for dvb-s2 st...

  • Page 35

    23 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.1.4 main screen for the dvb-s in the table below, it is explained the function of each parameter. These values are numbered in the order they appear in the main screen. Parameter nº function 1 transmission frequency (mh...

  • Page 36

    24 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 11 video options:  profile (mpeg-4 4:2:0 or mpeg-4 4:2:2)  delay (standard (s), low delay (l), super low delay (sl) or ultra low delay (ul)) table 3.5 main screen for dvb-s2 standard figure 3.5 main screen for dvb-s2 st...

  • Page 37

    25 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.2 transmission examples next, they are shown some setup examples and the image that appears in the monitor screen. Example 1 (dvb-t) setup:  frequency: 1250 mhz  transmission standard: dvb-t  output power: +5 dbm  f...

  • Page 38

    26 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 example 2 (dvb-s2) setup:  frequency: 1500.00 mhz (l band)  transmission standard: dvb-s2  output power: +0 dbm  symbol rate: 12.4 msymb/s  bandwidth: 16 mhz  modulation scheme: 32apsk  fec: 8/9  transmitted bitra...

  • Page 39

    27 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 example 3 (dvb-s) setup:  frequency: 1360.5 mhz (l band)  transmission standard: dvb-s  output power: +3.0 dbm  symbol rate: 8 msymb/s  bandwidth: 10 mhz  modulation scheme: qpsk  fec: 7/8  transmitted bitrate: 12...

  • Page 40

    28 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.3 leds the hdt-02 transmitter has 4 leds on its front panel that show the information detailed below. The on/off provides the following information:  if the led is off the equipment is not being fed.  the led flickers...

  • Page 41

    29 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.4 front panel the hdt-02 camera transmitter is configured following a menus structure on the display. The front panel has 8 buttons to enter and exit the equipment’s control menus and submenus and to navigate through th...

  • Page 42

    30 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.4.2 ok button this button is used to:  enter submenus and parameters to be changed. So as to access to a submenu, ok button must be pressed. Moreover, in the fields where the enter symbol appears, by pressing the ok bu...

  • Page 43

    31 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.4.4 left and right button these buttons are used to:  once the parameter to change has been selected, they are used to move the cursor towards the digit immediately on the left or right and to select a parameter from d...

  • Page 44

    32 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.4.6 rf button by pressing the rf button, rf output is enabled or disabled. The rf led indicates the status of the rf output. To enable or disable the rf output just press rf button. It is important that before pressing ...

  • Page 45

    33 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5 menus there is one menu in this transmitter that allows the operator to change transmitter parameters and to configure them. To enter the menu of this equipment cross button should be pressed. In case it is wanted aga...

  • Page 46

    34 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 continued hdt-02_h.264 menu structure format encoder video main screen frequency, standard, power, fft, bandwidth, modulation, fec,gi, latency, output bitrate, audio and video status, profile sdi hdmi cvbs asi gen type fo...

  • Page 47

    35 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 continued continued continued continued audio 2 data analogue embedded aes-ebu tone.Gen none none gps rs232 rs485 udp bitrate type bitrate bitrate bitrate frequency level baudrate parity stop bits encoder did.

  • Page 48

    36 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 continued continued ts parameters output video pid bitrate audio1 pid pmt pid pcr pid data pid program nº network name audio2 pid ts id network id service name ca-biss mode sw user none biss-1 biss-e continued encoder.

  • Page 49

    37 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 continued freq power modul mode ldpc fec gi bandwidth roll off freq modulator power const bandwidth ldpc fec sr 10 mhz freq power modul fec gi bandwidth mod&rf unit dvb-t2 dvb-t dvb-s2 alarms monitor ethernet firmware nig...

  • Page 50

    38 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.1 menu navigation this section contains a detailed description of each of the parameters that can be configured in the hdt-02_h.264 camera transmitter via the menu. To enter the menu, press the cross button in case of...

  • Page 51

    39 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2 menu structure the following menu screen can be accessed by pressing the cross key from the monitoring menu. Figure 3.17 menu encoder – all parameters relating to the video, audio and data inputs are configured here...

  • Page 52

    40 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1 encoder menu by using the up, down arrow keys, select the encoder optionand press ok key. Figure 3.18 encoder menu in the first field, the video input must be chosen with the right and left arrows buttons. Once th...

  • Page 53

    41 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.1 sdi input figure 3.19 sdi input menu line nº function 1 format (sdi): in this field, the format of the sdi input signal is displayed. (reading parameter) the available options are:  1080p (1920x1080) – 23.98/24...

  • Page 54

    42 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4 gop: in this field, the group of figures parameter is displayed. It specifies the order in which intra- and inter-frames are arranged. (eligible parameter) the available options are:  auto  manual (editable parameter)...

  • Page 55

    43 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.2 hdmi input figure 3.20 hdmi input menu line nº function 1 format: in this field, the format of the hdmi input signal must be selected. So as to select a format first, press the ok button so as to enter to the su...

  • Page 56

    44 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4 gop: in this field, the group of figures parameter is displayed. It specifies the order in which intra- and inter-frames are arranged. (eligible parameter) the available options are:  auto  manual (editable parameter)...

  • Page 57

    45 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.3 cvbs input figure 3.21 cvbs input menu line nº function 1 format (cvbs): in this field, the format of the cvbs input signal is displayed. (reading parameter) the options available are:  480i  576i 2 delay: in ...

  • Page 58

    46 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4 gop: in this field, the group of figures parameter is displayed. It specifies the order in which intra- and inter-frames are arranged. (eligible parameter) the available options are:  auto  manual (editable parameter)...

  • Page 59

    47 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.4 asi input figure 3.22 asi input menu line nº function 1 status: in this field it is indicated if there is any asi signal in the asi input. In case there is an asi signal, this field will display the word present...

  • Page 60

    48 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.5 generator input figure 3.23 generator input menu line nº function 1 format: in this field the format of the video signal generated is displayed. The only option available is 576/50i. (reading parameter) the avai...

  • Page 61

    49 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4 gop: in this field, the group of figures parameter is displayed. It specifies the order in which intra- and inter-frames are arranged. (eligible parameter) the available options are:  auto  manual (editable parameter)...

  • Page 62

    50 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.6 audio1 embedded figure 3.24 audio embedded input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 1. So as to select the desired bitrate, pr...

  • Page 63

    51 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.7 audio1 analogue figure 3.25 audio analogue input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 1. So as to select the desired bitrate, pr...

  • Page 64

    52 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.8 audio1 aes-ebu figure 3.26 audio aes-ebu input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 1. So as to select the desired bitrate, pres...

  • Page 65

    53 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.9 audio1 tone.Gen figure 3.27 audio generator input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 1. So as to select the desired bitrate, p...

  • Page 66

    54 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.10 audio2 embedded figure 3.28 audio embedded input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 2. So as to select the desired bitrate, p...

  • Page 67

    55 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.11 audio2 analogue figure 3.29 audio analogue input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 2. So as to select the desired bitrate, p...

  • Page 68

    56 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.12 audio2 aes-ebu figure 3.30 audio aes-ebu input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 2. So as to select the desired bitrate, pre...

  • Page 69

    57 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.13 audio2 tone.Gen figure 3.31 audio generator input menu line nº function 1 bitrate: in this option it can be selected the bitrate for the codification of the audio signal 2. So as to select the desired bitrate, ...

  • Page 70

    58 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.14 data so as to select the desired sort of data, press right, left buttons. (eligible parameter) data option parameters 1 none: this option is selected in case no data is sent to the transmitter. 2 gps: if this o...

  • Page 71

    59 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 gps screen so as to access to the gps screen first, go to the encoder option in the menu. Then, go to the data option and select gps with the right, left keys. Next, press the ok button so as to access to the gps screen. ...

  • Page 72

    60 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.15 encoder output figure 3.33 encoder output menu line nº function 1 bitrate: in this field, the output bitrate is shown. It case it is wanted to select between an automatic bitrate or configure manually the bitra...

  • Page 73

    61 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.1.16 ts parameters figure 3.34 encoder ts menu encoder ts video pid: 273 audio1 pid: 512 audio2 pid: 513 encoder ts data pid: 2100 pmt pid: 291 pcr pid: 256 encoder ts program nº: 1 ts id: 7 network id: 7 encoder ts...

  • Page 74

    62 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 line nº function 1 video pid: here the video packet identifier must be entered. So as to change its value first, press the ok button and then, with the up, down arrows select the number wanted. Press the ok button so as t...

  • Page 75

    63 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 8 ts id: here the transport stream identifier must be entered. So as to change its value first, press the ok button and then, with the up, down arrows select the number wanted. Press the ok button so as to save the value ...

  • Page 76

    64 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.2 ca-biss menu by using the up, down arrow keys, select the ca-biss optionand press ok key. Figure 3.35 ca-biss menu line nº function 1 mode: so as to choose the desired encryption, press the right, left keys. (elig...

  • Page 77

    65 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 so as to introduce the key in the biss-1 option, follow these steps: 1. Choose biss-1 option in the mode field. 2. Go one field down (sw) and press ok button so as to be allowed to introduce the key. 3. With left and righ...

  • Page 78

    66 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3 mod&rf menu by using the up, down arrow keys, select the mod&rf optionand press ok key. Figure 3.36 mod&rf menu 3.5.2.3.1 dvb-t2 figure 3.37 dvb-t2 & rf menu modulator & rf dvb-t2 dvb-s2 dvb-t dvb-s* dvb-t2 & rf f...

  • Page 79

    67 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 line nº function 1 freq: select the frequency at which the signal is going to be transmitted. So as to establish the frequency value first, press the ok button and then, with the up, down arrows buttons select the wanted ...

  • Page 80

    68 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5 gi: here the guard interval value can be chosen. Use right, left buttons so as to select the desired value. The value between brackets means the scattered pilot pattern and is a monitoring parameter. (eligible parameter...

  • Page 81

    69 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.2 dvb-t2 maximum bitrates these maximum values are reached under the following conditions: 8-mhz channel, 8k mode,g.I.=1/128. Modulation scheme code rate bit rate (mbps) qpsk 1/2 7.0 3/5 8.4 2/3 9.4 3/4 10.5 4/5 1...

  • Page 82

    70 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.3 dvb-t figure 3.38 dvb-t & rf menu line nº function 1 freq: select the frequency at which the signal is going to be transmitted. So as to establish the frequency value first, press the ok button and then, with th...

  • Page 83

    71 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4 fec: here the value of the forward error correction can be chosen. Use right, left buttons so as to select the desired value. (eligible parameter) the available parameters are:  1/2  2/3  3/4  5/6  7/8 5 gi: here t...

  • Page 84

    72 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.4 dvb-t useful bitrate in this point, useful bitrates are given for the 4k mode in the following tables and cover the 8 mhz, 7 mhz and 6 mhz channels. In the following tables, the values in italics are approximate...

  • Page 85

    73 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 table 3.28 useful bitrate (mbit/s) for non-hierarchical systems in 6 mhz channels table 3.29 useful bitrate (mbit/s) for non-hierarchical systems in 5 mhz channels.

  • Page 86

    74 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.5 dvb-s2 figure 3.39 dvb-s2 & rf menu dvb-s2 & rf freq: 1.640,365mhz low carrier power: +0.0dbm dvb-s2 & rf modul: 32apsk ldpc fec: 9/10 sr: 12.4ms/s bw:14 dvb-s2 & rf roll off: 0,20 pilots: on spectrum: normal dv...

  • Page 87

    75 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 line nº function 1 freq: select the frequency at which the signal is going to be transmitted. So as to establish the frequency value first, press the ok button and then, with the up and down arrows buttons select the want...

  • Page 88

    76 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5 ldpc fec: here the value of the forward error correction can be chosen. Use right and left buttons so as to select the desired value. (eligible parameter) the available options are:  1/4  1/3  2/5  1/2  3/5  2/3 ...

  • Page 89

    77 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 9 spectrum: here the type of the spectrum is configured. Inverted spectrum is just another method to help prevent signal theft. Use right and left buttons so as to select the desired option. (eligible parameter) the avail...

  • Page 90

    78 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.6 symbol rate calculation so as to calculate the symbol rate needed for a determined bandwidth, the next equation must be implemented: where: sr: symbol rate in msymb/s bw: bandwidth in mhz next, it is shown a tab...

  • Page 91

    79 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.3.7 dvb-s figure 3.40 dvb-s & rf menu dvb-s & rf freq: 1.360,500mhz modulator on power: +0.0dbm dvb-s & rf fec: 7/8 sr: 12.4ms/s bw:14 spectrum: normal dvb-s & rf 10mhz: on.

  • Page 92

    80 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 line nº function 1 freq: select the frequency at which the signal is going to be transmitted. So as to establish the frequency value first, press the ok button and then, with the up and down arrows buttons select the want...

  • Page 93

    81 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 bw: in this field it is displayed the value of the bandwidth of the transmitted signal. (reading parameter) 6 spectrum: here the type of the spectrum is configured. Inverted spectrum is just another method to help prevent...

  • Page 94

    82 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.4 unit menu by using the up, down arrow keys, select the unit optionand press ok key. Figure 3.41 unit menu 3.5.2.4.1 profile figure 3.42 unit menu in this option, a new profile can be created or, otherwise, an exis...

  • Page 95

    83 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.4.2 alarms in this option, different alarms which are present in the device are shown. The alarm screen can be accessed by pressing the ok button from the main screen as well. So as to return to the main screen from...

  • Page 96

    84 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.4.4 ethernet figure 3.44 encoder menu line nº function 1 local ip: in this option it can be set the ip address of the device in case it is wanted to control the device remotely. So as to change the ip address first ...

  • Page 97

    85 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.4.5 firmware figure 3.45 encoder menu line nº function 1 check usb memory: this field is the one for updating the version of the device. So as to update the equipment properly, follow the instructions below. 2 resto...

  • Page 98

    86 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 next, they are explained the necessary steps so as to make a successful update. 1) the latest firmware is allocated in the webpage of svp broadcast microwave. So as to access to the firmware file, first enter to www.Svpbm...

  • Page 99

    87 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3) click on software. Figure 3.47 updating firmware step 3 4) go to hdt-02_firmware. Figure 3.48 updating firmware step 4.

  • Page 100

    88 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5) select the firmware version to download the file. Figure 3.49 updating firmware step 5 6) once the firmware file has been downloaded, save it in a usb device. In the usb device, the only file that can be allocated insi...

  • Page 101

    89 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 3.5.2.4.6 night mode there are four possible states for the night mode. If night mode is in state 0 then the light in the screen will shine more than if it is in state 1. If the state is three then, the light in the scree...

  • Page 102

    90 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 4: gps application 4.1 introduction the hdt-02 transmitter has a gps antenna input in order to give information to the device about the positioning data. Connecting the gps antenna to this input, allows the transf...

  • Page 103

    91 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 the data status field indicates with a darkened x that it is disabled. When this parameter is enabled and blinkers, this means that there is nothing connected to the data input. When this field alternates the value betwee...

  • Page 104

    92 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 satellite level: the level of each satellite signal received is shown in this field. Date: updated date is shown. 4.4 gps hdr-106 receiver screen so as to access to the gps screen, go to the decoder option in the menu. On...

  • Page 105

    93 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 height of the transmitter: the height of the transmitter from ground is specified in this value. Date: updated date is shown. Longitude of the transmitter: specifies the longitude position of the transmitter. Nº of satell...

  • Page 106

    94 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4.5 application example 1 – constant positioning suppose the transmitter device is on an aeroplane and constant positioning of the vehicle is wanted to be known. This is achievable with the next items: - hdt-02_h.264 tran...

  • Page 107

    95 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure 4.4 gps system example 1 picture hdt-02_h.264 transmitter with gps antenna hdr-106 gps screen receiver hdr-106 e20º45.512´ 10k47º1mt 04/10/13 n60º73.984´ s3 100km 100º 09:45:34 rs232 connection pc with google maps.

  • Page 108: Chapter 5: Web Server

    96 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 5: web server 5.1 introduction this equipment can be controlled by use of a pc connected at the rear panel ethernet connector . To enable the browser interface correctly the ip address, subnet mask and gateway nee...

  • Page 109

    97 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 4. Select gat option and set the gateway address. So as to change the gateway address first press ok button and then, with the up, down keys select the desired number. So as to change from one character to another, press ...

  • Page 110

    98 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.1 encoder figure 5.5 web server input screen 5.2.1.1 video - input: select the type of the video input. The video input options available are sdi, hdmi, cvbs, asi and test pattern. (eligible parameter) - format: here ...

  • Page 111

    99 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - delay: in this field, the delay of the coding process is configured. The available options are standard delay, low delay, super low delay or ultra low delay. (eligible parameter) - profile: in this field, the codificati...

  • Page 112

    100 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.1.4 rs-232 if it is wanted to send data to the transmitter through a rs232 connection, this option must be selected. It is also needed to configure the next parameters so as to achieve a successful communication: - b...

  • Page 113

    101 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - latitude: specifies the latitude position of the transmitter. (reading parameter) - longitude: specifies the longitude position of the transmitter. (reading parameter) - altitude: the height of the transmitter from gro...

  • Page 114

    102 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - ts id: in this field the transport stream identifier must be set. (editable parameter) - network id: in this option the network identifier must be specified. (editable parameter) - network name: specify the name of the...

  • Page 115

    103 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.2 mod_rf figure 5.7 web server mod_rf screen (dvb-t) - system: in this field the transmission standard can be chosen. The available options are dvb-t2, dvb-t, dvb-s2 and dvb-s. (eligible parameter) - rf status: selec...

  • Page 116

    104 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.2.1 dvb-t - frequency: introduce the frequency at which the signal is being transmitted. (editable parameter) - power: specify the power at which the signal is being transmitted (1 db step). (eligible parameter) - mo...

  • Page 117

    105 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.2.2 dvb-t2 figure 5.8 web server mod_rf screen (dvb-t2) - frequency: introduce the frequency at which the signal is being transmitted. (editable parameter) - power: specify the power at which the signal is being tran...

  • Page 118

    106 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - mode: specify the fft mode. The available options are 1k,2k,4k, 8k,8k.Ext. (eligible parameter) - bandwidth: enter the transmitted signal bandwidth. The available options are 1.7, 5, 6, 7, 8 mhz. (eligible parameter) -...

  • Page 119

    107 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.2.3 dvb-s2 figure 5.9 web server mod_rf screen (dvb-s2) - frequency: introduce the frequency at which the signal is being transmitted. (editable parameter) - output mode: specify the transmission mode which can be no...

  • Page 120

    108 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - pilots: in this field, selecting the on option, carrier pilots are transmitted. If off option is selected, then no carrier pilots are transmitted. (eligible parameter) - symbol rate: in this field the value of the symb...

  • Page 121

    109 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.2.4 dvb-s figure 5.10 web server mod_rf screen (dvb-s) - frequency: introduce the frequency at which the signal is being transmitted. (editable parameter) - output mode: specify the transmission mode which can be no ...

  • Page 122

    110 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 - spectrum: here the type of the spectrum is configured. Inverted spectrum is just another method to help prevent signal theft. The spectrum options are inverted and normal. (eligible parameter) - bandwidth: in this fiel...

  • Page 123

    111 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.2.4 unit figure 5.12 web server unit screen 5.2.4.1 leds status (reading parameters) - on/off: o if the led is off the equipment is not being fed. O the led lights up in green when the equipment is turned on. - rf: o i...

  • Page 124

    112 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 o the different warnings that can appear in the transmitter are:  no video input.  no gps. - status: the led lights up when a change in the configuration of the device is being processed. 5.2.4.2 alarms (reading parame...

  • Page 125

    113 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 5.3 web page setup notes in order for the data to be refreshed correctly, you may need to change some settings on your browser. Please follow these instructions carefully. For google chrome: 1. Make click in the chrome m...

  • Page 126

    114 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure 5.13 snmp management system the snmp agent used is mib-ii compliant. The svp mib (management information database) provides a standard representation of the snmp agent’s available information and where it is store...

  • Page 127: Chapter 6: Remote Control

    115 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 6: remote control 6.1 introduction this equipment, called rtc-01, is a compact lightweight remote control for svp broadcast microwave systems. It can control the hdr-106 receiver and the hdt-02 transmitter. The c...

  • Page 128

    116 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 6.2 application example suppose the transmitter device is on an aeroplane, concretely on the deck of the aeroplane which is far from the pilot. If the pilot wanted to change any parameter of the transmitted signal (for e...

  • Page 129

    117 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 chapter 7: equipment installation 7.1 introduction this chapter provides important information for transmitter system installation such as connections available in the rear and front panel of the hdt-02 transmitter and t...

  • Page 130

    118 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure 7.2 hdt-02 front panel figure 7.3 hdt-02 rear panel.

  • Page 131

    119 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure 7.4 hdt-02 front panel figure 7.5 hdt-02 rear panel technical features of each connection are described on the following sections. Dvb-t2 2.8-4ghz rf connector dvb-t2 4-6ghz rf connector uhf remote connector dvb-s...

  • Page 132

    120 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1 input connections in this section technical features about the input connections available and the connectors needed are described. In all the lemo connectors, the pin number one is circled and the succeeding pins ...

  • Page 133

    121 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1.2 cvbs/ sdi/ hdmi/ asi input the hdt-02_h.264 transmitter incorporates a hdmi input so as to allow that new devices can be connected. Sd-sdi digital video input is compatible with smpte-259m standard, hd- sdi digit...

  • Page 134

    122 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 hdmi connection technical features item features connector label hdmi connector type type a table 7.5 hdmi input signal connection features sdi connection technical features item features connector label sdi connector ty...

  • Page 135

    123 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1.3 audio inputs the hdt-02 transmitter has four possible audio inputs:  2 audio inputs to insert 2 stereo channels aes/ebu, 2 stereo or 4 mono analogue (mic phantom, mic dynamic and line) signals where connections ...

  • Page 136

    124 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 pinout of the cable connector (watched from the soldering side) pin description 1 a1l+ / aes1p 2 a1l- / aes1n 3 gnd 4 a1r+ 5 a1r- table 7.9 aes/ebu and analogue audio cable connector pinout 2 5 3 4 1.

  • Page 137

    125 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1.4 data/gps input this input is mainly used in order to transfer gps data or user data through connections made using 6 pin lemo 0bconnector on equipment’s rear panel. Thanks to this characteristic it is possible to...

  • Page 138

    126 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1.5 rtc connection so as to provide the remote control of the transmitter, it has been added a rtc input. Connections are made using 4 pin lemo 0b connector on equipment’s rear panel. This feature can be used, for ex...

  • Page 139

    127 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.1.6 usb connection thanks to the usb connection, it is possible to update directly from an external usb device the firmware of the hdt-02 transmitter. The connector is type a. Usb connection technical features item f...

  • Page 140

    128 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.2 output connections in this section technical features about the output connections available and the connectors needed are described. 7.2.2.1 rf output/antenna the antenna or power amplifier is directly connected t...

  • Page 141

    129 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.2.2.2 asi output asi output signal type uses 75Ω bnc connector. This connector is placed on transmitter’s rear panel. It is important that 75 Ω connectors are used. This is because the female output connector of the hd...

  • Page 142

    130 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.3 mechanical accessories in this section different short of accessories of the hdt-02_h.264 transmitter are shown. The items wanted by the customer are defined when the transmitter is ordered. 7.3.1 transmitter fasteni...

  • Page 143

    131 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure 7.5 part number: cltx01 dimensions: 17.3x14.2 cm / 6.8x5.6 in weigh: 126 gr / 4.4 oz.

  • Page 144

    132 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 7.3.2 battery fastening this item allows connecting a battery (v type or anton bauer) to the transmitter’s case. The type of the battery fastening must be defined when the transmitter is ordered. Figure 7.7 v type batter...

  • Page 145: Important Notes

    133 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 index a - pa-5 and pa-10 power amplifiers important notes 1. Read the instructions carefully before connecting the machine. 2. Do not remain close to the antennas when the amplifier is in operation. 3. In our effort to c...

  • Page 146: A.1 Introduction

    134 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.1 introduction the pa -5 and pa-10 series power amplifiers expands the possibilities of cofdm digital links on the market, since they can work with most transmitter types. Low intermodulation and high reliability make ...

  • Page 147: A.2 Technical Features

    135 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.2 technical features a.2.1 main characteristics pa-10 max. Output power 10 w linear frequency range 1.65 to 1.90 ghz (pa-10_1.6g) 2.0 to 2.5 ghz (pa-10_2.0g) 3.1 to 3.5 ghz (pa-10_3.1g) 4.4 to 5.1 ghz (pa-10_4.4g) 6.25...

  • Page 148

    136 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 weigh with all except from pa-10_4.4g: heatsink 1.3 kg. / 2.86 lb pa-10_4.4g: 2.6 kg. / 5.72 lb connectors rf: n-female standard (another under request) dc and control: amphenol pto, 4-pin gain pa-10_1.6g: 20 db typ pa-1...

  • Page 149

    137 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 pa-5 max. Output power 5 w linear frequency range 1.15 to 1.45 ghz (pa-5_1.1g) 1.65 to 1.90 ghz (pa-5_1.6g) 2.0 to 2.5 ghz (pa-5_2.0g) 3.1 to 3.5 ghz (pa-5_3.1g) 4.4 to 5.1 ghz (pa-5_4.4g) 6.25 to 6.55 ghz (pa-5_6.2g) ha...

  • Page 150

    138 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 gain pa-5_1.1g: 17 db typ pa-5_1.6g: 17 db typ pa-5_2.0g: 17 db typ pa-5_3.1g: 17 db typ pa-5_4.4g: 30 db typ pa-5_6.2g: 23 db typ evm 2.5% typ, 8 mhz cofdm 3% typ, 8 mhz cofdm (pa- 5_6.2g model) acpr -32 dbc typ, 8 mhz ...

  • Page 151

    139 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.2.2 connections either of the amplifiers have three connections available:  dc: for the power supply.  rf in: here is connected the rf signal which comes from the hdt-02 transmitter  rf out: here is the output for t...

  • Page 152

    140 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 rf in and out connector n female type connector in all of the available amplifiers for rf input and output. Conector needed figure a.4 n male connector.

  • Page 153

    141 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.2.3 thermal protections the device has a water proof radiator that dissipates heat throughout a fan. The fan is activated when temperature exceeds a determined value. Figure a.5 front view of the pa cofdm amplifier. Pa...

  • Page 154

    142 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.2.4 before you connect the device 1. Make sure that you have the right battery for the equipment to operate. 2. Be particularly careful of the continuous power’s polarity. The power amplifier is protected against rever...

  • Page 155

    143 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.2.5 installation for the installation of the pa 10 or pa 5 amplifier, there are needed these items:  pa 10 or pa 5 power amplifier  hdt-02 transmitter  rf cable with n male to n male type connector.  4 pin amphenol...

  • Page 156

    144 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 interface item thanks to an intermediate sheet between the transmitter and the power amplifier, it is possible to put the amplifier (both pa 10 and pa 5) above the hdt-02. Next, there are shown this configuration and the...

  • Page 157

    145 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure a.9 part number: cltx02 dimensions: 17.3x12.4 cm / 6.8x4.9 in weigh: 106 gr / 3.7 oz.

  • Page 158

    146 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 devices placed separately the other option is to place both of the devices (transmitter and power amplifier) separately, which can be clamped to other structure thanks to an available clamping support, as shown in the ne...

  • Page 159

    147 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure a.12 part number: cltx01 dimensions: 17.3x14.2 cm / 6.8x5.6 in weigh: 126 gr / 4.4 oz.

  • Page 160

    148 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure a.13 part number: cltx03 dimensions: 13.5x11.1 cm / 5.3x4.4 in weigh: 123 gr / 4.3 oz.

  • Page 161

    149 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 a.3 power amplifier control the new power amplifiers allow the user to control automatically the power that these devices provide. In order to achieve this characteristic, it is necessary to have the rf on button switche...

  • Page 162: B.1 Description

    150 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 index b – avf x03 flexible antenna b.1 description avf-x03 model antenna, which is a linear omnidirectional flexible antenna, is suitable for the 1.3 to 7.5 ghz frequency band. It is very useful for mobile camera links a...

  • Page 163

    151 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 b.2 technical specifications item feature frequency range 1.3 to 7.5 ghz (different bands available) gain 3 dbi polarization linear (vertical) beamwidth 76ºv and omnidirectional h bandwidth depends on the frequency range...

  • Page 164

    152 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure b.2 horizontal and vertical radiation patterns.

  • Page 165: Index C – Gps Antenna

    153 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 index c – gps antenna c.1 description our satellite receiver is a compact and easy solution for sending the position where our transmitter is located. It’s very useful to know the position of the helicopters, motorcycles...

  • Page 166

    154 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 c.2 technical specifications item feature power supply +5v (provided by the transmitter) dimension l: 47mm, w: 38mm, h: 16mm receiving frequency 1,575.42 mhz mounting magnetic base sensibility -158 dbm start-up time 1 se...

  • Page 167

    155 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 figure c.2 link with gps scheme antenna tx antenna rx with down converter hdt-02 gps antenna hdr-106 pc with google maps rs-232 at 9600 baud.

  • Page 168

    156 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 index d – modulation standards this chapter describes the dvb-t/t2 and dvb-s/s2 standards, as well as their features and the differences between them. D.1 dvb-t dvb-t is a technical standard that specifies the framing st...

  • Page 169: D.2 Dvb-T2

    157 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.2 dvb-t2 dvb-t2 is the world’s most advanced digital terrestrial television (dtt) system, offering more robustness, flexibility and at least 50% more efficiency than any other dtt system. It supports sd, hd, uhd, mobil...

  • Page 170

    158 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 constellation rotation this new feature consists on a rotation of some degrees of the constellation. With this rotation, dependence between the i and q components of the signal is achieved. This means that with only one ...

  • Page 171

    159 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.2.3 dvb-t vs dvb-t2 next, it is shown a comparison table between the two existing dvb terrestrial standards. The new features of the dvb-t2 standards respect to the dvb-t are in bold. Dvb-t dvb-t2 (new/improved options...

  • Page 172: D.3 Dvb-S

    160 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.3 dvb-s dvb-s is the first generation of a standard for digital broadcasting via satellite. D.3.1 how does it works dvb-s was designed to carry mpeg-2 transport streams over satellite. Mpeg-2 transport streams typicall...

  • Page 173: D.4 Dvb-S2

    161 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.4 dvb-s2 dvb-s2 is a digital satellite system developed by the dvb project. It makes use of the latest modulation and coding techniques to deliver performance that approaches the theoretical limit for such systems. D.4...

  • Page 174

    162 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 forward error correction dvb-s2 uses a very powerful forward error correction scheme (fec), a key factor in allowing achievement of excellent performance in the presence of high levels of noise and interference. The fec ...

  • Page 175

    163 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 variable coding and modulation (vcm) (used in the hrd-106 and ird-70) variable coding and modulation is a mode of operation that allows different modulation parameters to be applied to the different dvb-s2 streams of a m...

  • Page 176

    164 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 adaptive coding and modulation (acm) (used in the hrd-106 and ird-70) in adaptive coding and modulation mode, the modulation parameters of the baseband frames can vary over time, according to the instantaneous receiving ...

  • Page 177

    165 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.4.2 pilots in dvb-s2 pilots are unmodulated symbols grouped in blocks that can be added on the physical layer framing level. Pilots are used to: - reduce the phase noise influence. Phase noise is created by the frequen...

  • Page 178

    166 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 d.4.3 dvb-s vs dvb-s2 next there are shown a series of comparisons between dvb-s and dvb-s2 standards. Dvb-s vs dvb-s2 performance figure d.10 dvb-s vs dvb-s2 performance in the figure above it is shown how the dvb-s2 st...

  • Page 179

    167 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 main differences between dvb-s and dvb-s2 dvb-s dvb-s2 meant for broadcast only fully transparent to all data fixed 188 byte/packets baseband in 16 or 64 kbps one ts/carrier ccm/multistream – vcm – acm rs and viterbi cod...

  • Page 180

    168 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 glossary aes/ebu audio engineering society/european broadcasting union acpr adjacent channel power ratio apsk amplitude and phase-shift keying or asymmetric phase-shift keying (apsk) asi asynchronous serial interface bnc...

  • Page 181

    169 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 evm error vector magnitude fec forward error correction fft fast fourier transform gps global positioning system hd high definition hdmi high-definition multimedia interface hdr high definition receiver hdt high definiti...

  • Page 182

    170 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 pal phase alternating line pid packet identification qam quadrature amplitude modulation qpsk quadrature phase-shift keying rf radiofrequency rtc remote control sd standard delay sdi serial digital interface snmp simple ...

  • Page 183

    171 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11.

  • Page 184

    172 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 notes.

  • Page 185: Final Note

    173 hdt-02_h.264 high definition digital camera transmitter user’s manual v4.11 final note svp broadcast microwave s.L. Is constantly striving to improve all of its products. Therefore, we ask you to understand that modifications may occur in designs, equipment and technology. Consequently, no respo...

  • Page 186

    Svp broadcast microwave reserves the right to make changes to this manual and to the equipment without prior notice. Svp broadcast microwave c/ zubiaurre 7 bajo 48215 iurreta vizcaya – españa tel: (+34) 94620 3722 info@svpbm.Com www.Svpbm.Com.