SWAGTRON K2 Quick start manual
1
1
Assembling the Rear Wheels
• Remove the Nuts and Spacers from the Rear Axle if needed.
• Slide the Rear Axle through the Center Tube in the Rear Assembly holes so that it
extends from either side (
Figure 1).
• Slide the 1x Spacer and 1x Rear Wheel onto one end of the Rear Axle.
• At the other side of the Rear Wheel, attach 1x Nut to the end of the Rear Axle.
• Slide the 1x Spacer and 1x Rear Wheel onto the other end of the Rear Axle.
• At the other side of that Rear Wheel, attach 1x Nut to the end of the Rear Axle.
• Tighten the nuts with the Socket Spanner provided (
Figure 2).
• Push each Cover over each Nut and into the Wheels.
Adjusting the Stem
• Open the Upper Clamp (
Figure 4).
• Press the metal pegs on the Stem and push
up or down the handlebar to adjust the
height.
• Close the Upper Clamp to secure the
handlebar.
• The metal peg MUST pop into one
of the two designated holes in order
for the scooter to be safe to ride.
• The Stem may need to be adjusted
after switching modes.
2-in-1 Child Walker, Balance
Bike, and Scooter
Quick Start Guide
Product Overview
2
Before Riding Your Scooter
3
Box Contents
1
Front Assembly x 1
Quick Start Guide x1
Axle Parts Pack x 1
Rear Assembly x 1
Rear Wheel x 2
1
Handle
2
Upper Clamp
3
Stem
4
Seat
5
Deck
6
Turning Point
7
Socket Spanner (2x sets)
7
8
9
Usage Instructions
4
2
Bike Mode
Axle Parts Pack
Scooter Mode
8
Covers (for rear wheels)
9
Rear Axle (with 2x Spacers
& 2x Nuts)
Cover
Cover
Spacers
Nut
Nut
Rear Wheel
Rear Wheel
Center Tube Rear Axle
How to Use Your Scooter
■
Age-appropriate protective gear including a helmet and elbow
and knee-pads must be worn at all times.
■
The scooter supports up to 44 lbs (20kg).
Assuming you have equipped suitable protective gear and that the scooter has
been placed on a level surface, follow the steps below.
Bike Mode
• Hold both handles firmly.
• Sit down on the seat.
• With your both feet, push off the ground to propell the scooter forward.
• Both feet can leave the ground when desired speed has been reached.
• To stop, step on the ground with both feet.
Scooter Mode
• Hold both handles firmly.
• Put your one foot towards the front of the deck.
• With your other foot, push off the ground to propell the scooter forward.
• Both feet can fit on the deck when desired speed has been reached.
• To stop, step on the ground with one foot.
Practicing Guidelines
• Wear casual clothing and flat shoes to maintain your flexibility and stability.
• Practice until you can easily get on, move forward, turn, stop, and dismount
with ease.
• Make sure the pavement is even. Do not ride on a slope until you are
experienced.
• The Scooter is designed for relatively smooth, flat terrain. When driving on
uneven terrain, the user should slow down.
• Until you are comfortable using the scooter, avoid riding in places with
pedestrians or obstacles.
Before operating this vehicle, please read all instructions. This guide will walk you through
the functions, usage, and proper care of your SWAGTRON
®
K2 Kid’s scooter. If you have
any questions or cannot find the information you need in the guide, please contact your
place of purchase or our customer service at
1-844-299-0625.
Assembling the Whole Scooter
• At the Turning Point, push the two metal pegs in
on both sides and attach the Front Assembly to
the Rear Assembly.
Ensure the metal pegs pops into the
designated holes.
Metal Pegs Hole
Figure 3
Figure 1
Figure 2
Switching Modes (Bike Mode &
Scooter Mode)
• At the Turning Point, push the two metal
pegs on both sides.
• Turn the Rear Assembly 180° according
to preference. The deck should face up
for Scooter Mode while the seat should
face up for Bike Mode.
Protective Cover
Metal Pegs
Figure 5
1
2
3
4
5
6
6
Upper Clamp
Metal Pegs
Figure 4
To use the Socket Spacers, slide each pin into each tube making sure the
flattened end faces up. Fit each spanner over each Nut. Use one spanner
to hold 1x Nut in place and turn other spanner tighten.