Part# tc36.Ng03.C. For tc36 tc36 black diamond burner kit instructions 010408-16 tc36.Ng03.C 5056.427.C3 installer: leave this manual with the appliance. Consumer: retain this manual for future reference. These instructions are supplementary to the installation and operating instructions supplied wi...
Tc36.Ng03.C 010408-16 2 • burner tube • media spacer, rear • burner tray assy • media spacer, front • 5 lbs. Tumbled glass • media spacer, center • burner shield • panel, lower rear • manifold assembly (including supply tube) • pilot shield (including pilot and supply tube) • hardware package note: ...
Tc36.Ng03.C 010408-16 3 fig. # 4 2) attach the manifold bracket to the fl oor shield in the bottom of the fi rebox with one screw. (fig. # 2) 3) attach the manifold and pilot supply tubes to the bulk head fi tting and tighten. (fig. # 3) ensure that all connections are gas tight. 4) attach spark ele...
Tc36.Ng03.C 010408-16 4 fig. # 5 5) remove panel retaining clips from the upper heat shield. Install right side panel by placing the bottom into the fi rebox and tipping the top into position. (fig. # 5) 6) position upper rear panel on top of lower rear panel and slip in behind the right panel. (fig...
Tc36.Ng03.C 010408-16 5 fig. # 8 fig. # 9 fig. # 10 8) install burner shield by tipping the shield into the fi rebox, feed the pilot assembly through the opening in the shield. (fig. # 8) 9) attach pilot shield to burner tray with two screws. (fig. # 9) 10) attach the burner tray to the burner shiel...
Tc36.Ng03.C 010408-16 6 fig. # 11 fig. # 12 11) install front and rear media spacers. (fig. # 11 & 12) 12) install burner by tilting burner inlet through tray. Ensure that the orifi ce has entered the inlet tube. (fig. # 13 & 14) set the air shutter to fully open for propane or fully closed for natu...
Tc36.Ng03.C 010408-16 7 13) install the center media spacer. Secure the spacer and burner with two long screws.(fig. # 15) four holes must line up to set each screw. Some pressure may need to be applied to the front tray support on the shield to align the holes. (fig. # 16) fig. # 14 fig. # 15 fig. ...
Tc36.Ng03.C 010408-16 8 fig. # 17 14) apply just enough glass media to cover the burner assembly. (fig # 17) note: too much glass media over the burner will cause sooting with the use of propane gas.
Tc36.Ng03.C 010408-16 9 if the unit is to be used on propane convert as follows using the components supplied with this fi replace: warning this conversion kit shall be installed by a qualifi ed service agency in accordance with the manufacturer's instructions and all applicable codes and requiremen...
Tc36.Ng03.C 010408-16 10 6) slide the pilot adjustment band over and ensure that the hole in the orifi ce band is showing. (fig. #20 indicates ng position, fig. #21 indicates lp position) 7) remove access panel, 10 screws, and set aside 8) remove the minimum rate screw located in the valve. (fig. #2...
Tc36.Ng03.C 010408-16 11 fig. # 28 fig. # 27 fig. # 26 1) remove the plug from the pressure test port. The plug is located between the right side lintel and fi rebox side. (fig. # 27) 2) thread the extension test fi tting into the open test port. (fig. # 28) 3) attach a pressure gauge onto the fi tt...
Tc36.Ng03.C 010408-16 12 fig. # 29 the air shutter at the end of the burner inlet tube controls the primary combustion air to the gas burner and is preset closed at the factory for natural gas fuel. Shutter must be fully open for propane. See fig. #29 for proper fl ame pattern. The fl ame should be ...
Tc36.Ng03.C 010408-16 13 item ..... Description ..................................... Part no. 1............ Burner tube ............................ Tc36.5011835 2............ Orifice, ng ........................................... 5022.13 .............. Orifice, lp ...................................
Tc36.Ng03.C 010408-16 14 notes.
Tc36.Ng03.C 010408-16 15 notes.
Technical support: 1-877-715-2664 www.Townandcountryfi replaces.Net 2975 allenby rd., duncan, bc v9l 6v8 printed in canada.
