181208-16 5056.4252105 tcws.54ng04.C1 part# tcws.54ng04.C1 for tcws series c these instructions are supplementary to the installation and operating instructions supplied with the fi replace and should be kept together. Refer to the installation and operating instructions for proper gas supply, safet...
Tcws.54ng04.C1 181208-16 2 3.4 lbs sand 1 hardware pack 2 equalizer rocks 1 1/2 ss flex line 1 pilot assembly 2 burner assemblies 1 burner tray assembly 4 pebble sets a a b b c c d d e e f f g g h h 2 contents of package.
Tcws.54ng04.C1 181208-16 if converting to propane see conver- sion instructions on page #8 before proceeding. Install panels according to the tcws.54ce installation and operating manual prior to burner installation. (page 23) 1. Attach fuel fl ex line and pilot assembly to bulkhead fi ttings. (fig. ...
Tcws.54ng04.C1 181208-16 4. Connect gas lines to both orifi ce assemblies on the mounting brackets. (fig. # 4) caution: ensure that all connections are gas tight. 5. Tilt burner tray length-wise and insert into the fi rebox. (fig. #5) 6. Attach pilot to burner tray. (fig. #6) orange wire fig #6 fig ...
Tcws.54ng04.C1 181208-16 7. Secure the burner tray to legs using four screws (fig. #7) note: a light will aid aligning the holes in the tray with the leg 8. Install the right burner by tipping into location trough and slipping the venturi tube over the orifi ce. Test for connection by lifting at a l...
Tcws.54ng04.C1 181208-16 11. Place each rock as per the following photographs, start from the right hand side of the burner and ensure that the arrow on each rock points towards the front of the fi replace. (fig. #11 to 22) 10. Each rock has a slot in it’s base and is marked with a letter and an arr...
Tcws.54ng04.C1 181208-16 wide edge to front of fireplace 14. Install front porcelain cover (wide edge should face the front). (fig. #23) 13. Place the two remaining rocks on the left hand end of burner as shown. (fig. #21 and 22) 12. Repeat the sequence of placing the rocks three more times until th...
Tcws.54ng04.C1 181208-16 warning this conversion kit shall be installed by a qualifi ed service agency in accordance with the manufacturer's instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, ...
Fig #18 tcws.54ng04.C1 181208-16 5. Slide the pilot adjustment band over and ensure that the hole in the orifi ce band is showing. Fig. #28a shows ng position fig. #28b shows lp position). 6. Remove the access panel, 10 screws, and set aside. 7. Lift the control box shield and rest on the edge of th...
Tcws.54ng04.C1 181208-16 12. Check all connections for leaks warning: both the control box shield and the access panel must be reinstalled after conversion/ installation or servicing has been completed. Failure to do so will overheat and cause premature failure of the control system. Control shield ...
Tcws.54ng04.C1 181208-16 1. Remove the plug from the pressure test port using a 3/16” hex key. The plug is located between the right side lintel and fi rebox side. (fig. #37) 2. Thread the extension test fi tting into the open port. (fig. #38) 3. Attach a pressure gauge onto the fi tting. 4. When te...
Tcws.54ng04.C1 181208-16 the air shutter on the burner tube controls the primary combustion air. It is set to the closed position at the factory for natural gas fuel. For lp see pg.8. Some adjustment may be neces- sary to obtain desired fl ame and to eliminate carbon deposits. Evaluate fl ame appear...
Not shown * * * * * tcws.54ng04.C1 181208-16 item .......Description ............................................Part no. #1.......... Tranquility burner kit........ Tcws.54ng04.C #2.......... Pebble assembly ......................... 5096.921 #3.......... Main supply tube .............................
Notes:.
Notes:.
Printed in canada technical support: 1-877-715-2664 web site: www.Townandcountryfi replaces.Net 2975 allenby rd., duncan, bc v9l 6v8.
