1. DL manuals
  2. Tadiran Telecom
  3. Computer Hardware
  4. Coral IPx Office
  5. Installation And Hardware Reference Manual

Tadiran Telecom Coral IPx Office Installation And Hardware Reference Manual

Summary of Coral IPx Office

  • Page 1

    Coral ipx office installation procedure and hardware reference manual creating a new world of ipportunities (edition 3).

  • Page 3

    © copyright by tadiran telecom ltd., 2006-2008. All rights reserved worldwide. The coral is protected by u.S. Patents 6,594,255; 6,598,098; 6,608,895; 6,615,404 all trademarks contained herein are the property of their respective holders. The information contained in this document is proprietary and...

  • Page 5

    I federal communications commission rules part 68 compliance statement this equipment complies with part 68 of the fcc rules. On this equipment is a label that contains, among other information, the fcc registration number and ringer equivalence number (ren) for this equipment. If requested, this in...

  • Page 6

    Ii canadian dot compliance statement notice: the industry canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate terminal equipment technical requiremen...

  • Page 7: Equipment Compliance

    Iii ul safety of information technology equipment compliance equipment certified according to ul has been tested and complies with the following: usl compliance usl indicates listing to u.S. Standard for information technology equipment including electrical business equipment, ul60950, third edition...

  • Page 8

    Iv ce compliance statement (rtt&e) equipment certified according to ce has been tested and complies with the following: en60950-1 en55022 en55024 the coral system may include a class i laser product. All laser transmitters integrated within the coral systems are approved class i laser units. Coral s...

  • Page 9: Part 15

    V federal communications commission part 15 the fcc wants you to know this equipment has been tested and found to comply with the limits for a class b digital device, pursuant to part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a re...

  • Page 10

    Vi waste of electrical and electronic equipment (weee) directive 2002/96/ec of the european parliament it is the responsibility of the distributor to fully comply with directive 2002/96/ec dated 27 january 2003 of the european parliament and of the council on waste of electrical and electronic equip...

  • Page 11: Table of Contents

    Vii table of contents chapter 1: introduction 1.1 about this manual..................................................................................................................... 1-1 document description .............................................................................................

  • Page 12

    Viii activating and initializing the control card ............................................................................. 3-5 memory lithium battery condition test .................................................................................. 3-9 3.3 identifying the coral expansion units.....

  • Page 13

    Ix 5.6 i/o card connections ............................................................................................................... 5-21 peripheral cards index ........................................................................................................... 5-21 champ connections ....

  • Page 14

    X card handling procedures...................................................................................................... 8-4 8.2 mcb office card ...................................................................................................................... 8-5 general information .......

  • Page 15

    Xi general description ................................................................................................................ 9-1 shared service cards in the main unit................................................................................... 9-1 card handling procedures..............

  • Page 16

    Xii general description ................................................................................................................ 9-57 available mfr circuits............................................................................................................ 9-57 specifications...........

  • Page 17

    Xiii introduction ............................................................................................................................. 9-93 circuit description................................................................................................................... 9-94 configuring...

  • Page 18

    Xiv assembling the wifi card ...................................................................................................... 11-13 removing the wifi card......................................................................................................... 11-16 assembling the wifi antennas...

  • Page 19: List of Tables

    Xv list of tables table 1-1: related documentation ...................................................................................................... 1-3 table 1-2: ipx office system specifications ........................................................................................ 1-12 tabl...

  • Page 20

    Xvi table 9-5: u-rmi office, u-mr office, rmi office and mr office configuration jumpers ................. 9-15 table 9-6: card led indications ......................................................................................................... 9-16 table 9-7: external connections ................

  • Page 21: List of Figures

    Xvii list of figures figure 2-1: coral ipx office main unit sizes ....................................................................................... 2-4 figure 2-2: coral ipx office expansion unit sizes and weights ......................................................... 2-4 figure 2-3: coral ...

  • Page 22

    Xviii figure 6-1: front view of the table-mounted ipx office unit.............................................................. 6-2 figure 6-2: front view of the rack-mounted ipx office unit............................................................... 6-2 figure 6-3: main unit front panel ...........

  • Page 23

    Xix figure 8-1: mcb office card layout ................................................................................................... 8-3 figure 8-2: mcb office card layout ................................................................................................... 8-7 figure 8-3: coral ...

  • Page 24

    Xx figure 9-37: simplified relay diagram................................................................................................ 9-105 figure 10-1: coral ipx office peripheral card slot location ............................................................... 10-6 figure 10-2: coral ipx offic...

  • Page 25

    Xxi figure 11-10: wifi antenna removal ................................................................................................. 11-18.

  • Page 27: Chapter

    Coral ipx office installation manual chapter 1 introduction 1.1 about this manual........................................................................1-1 1.2 about the coral ipx office ...........................................................1-9.

  • Page 29: 1.1

    Coral ipx office installation manual introduction 1-1 ab out this manu al 1 1.1 about this manual 0 the coral ipx office installation guide and hardware reference manual, is designed for field use by coral system installation and service personnel. It describes the installation of the coral ipx offi...

  • Page 30

    1-2 introduction coral ipx office installation manual ab out this manu al 1 chapters 6, 7, 8, 9, 10, and 11 describe the hardware reference. These chapters offer detailed technical information about ipx office system hardware, including cage specifications, internal power supplies, and interface cir...

  • Page 31: Related Documentation

    Coral ipx office installation manual introduction 1-3 ab out this manu al 1 for further information not in the scope of this manual about coral service cards, peripheral cards, voice terminals, voip devices, etc., consult the following documentation: table 1-1 related documentation ....................

  • Page 32

    1-4 introduction coral ipx office installation manual ab out this manu al 1 voice terminal equip- ment/ peripheral device description coral ipx and flexicom product description, chapter 3 installation, administration procedure, troubleshooting and hardware reference t207m, t208m, t207m/np and t208m/...

  • Page 33: Tip:

    Coral ipx office installation manual introduction 1-5 ab out this manu al 1 this manual includes information that requires special attention, or is distinguished from the main texts in some significant way. These are indicated by the use of symbols and text formatting. This is illustrated in the fol...

  • Page 34: List of Acronyms

    1-6 introduction coral ipx office installation manual ab out this manu al 1 0 30t (/m) office ... 30 channel, e1/cept digital trunk interface card 4t office ............ 4 analog loop-start trunk line with power fail circuits card 4t-cid office ..... Same as 4t-csl card with 4cid module 4tbr office ...

  • Page 35

    Coral ipx office installation manual introduction 1-7 ab out this manu al 1 esix office ........ Expansion shelf interface card in the expansion unit ipc2 office ........ Integrated pc card including sfc, ucmc, and wicmc voice mail applications cslx 200 .......... Optional expansion unit of the ipx ...

  • Page 36: Notes:

    1-8 introduction coral ipx office installation manual ab out this manu al 1 notes:.

  • Page 37: 1.2

    Coral ipx office installation manual introduction 1-9 about the coral ip x o ffice 1 1.2 about the coral ipx office 0 the coral ipx office is a 19"/23”, rack-mounted or table-mounted, compact system that provides a converged system with sophisticated call-handling. It includes a range of ip function...

  • Page 38

    1-10 introduction coral ipx office installation manual about the coral ip x o ffice 1 circuitry the coral ipx office includes digital communications switching based on pulse code modulation (pcm) switching technology. The active circuitry of the system is embedded on the mcb office card and removabl...

  • Page 39

    Coral ipx office installation manual introduction 1-11 about the coral ip x o ffice 1 major features the coral ipx office main unit houses all hardware components of the coral ipx office system, including the power supply unit, control cards, peripheral cards, service cards, and i/o connections. In ...

  • Page 40

    1-12 introduction coral ipx office installation manual about the coral ip x o ffice 1 table 1-2 ipx office system specifications specification * ipx office main unit ipx office ex † expansion unit ipx 500x cage ipx 800x cage flexicom 200 cslx cabinet control cards mcb office (1) — — px card ‡ (1 or ...

  • Page 41: Recommended Tools

    Coral ipx office installation manual introduction 1-13 about the coral ip x o ffice 1 0 the following tools are required in order to install and maintain the coral ipx office system: required tools: 4 mm (max.) flat blade screwdriver for installation and removal of the door 3/16", 1/4", and 5/16" st...

  • Page 42

    1-14 introduction coral ipx office installation manual about the coral ip x o ffice 1 optional tools: modular line polarity tester flashlight tone/continuity/talk battery generator tone detector/amplifier probe telephone line test set with mf tone signalling capability alligator clip leads amp™ cham...

  • Page 43: Chapter

    Coral ipx office installation manual chapter 2 hardware installation procedure 2.1 site inspection ...................................................................................2-1 2.2 equipment installation .......................................................................2-9 2.3 program ...

  • Page 45: 2.1

    Coral ipx office installation manual hardware installation procedure 2-1 si te inspection 2 2.1 site inspection 0 the coral ipx office system should be installed in restricted access areas (dedicated equipment rooms, equipment closets, etc.) in accordance with articles 110-16, 110-17, and 110-18 of ...

  • Page 46: Space Requirements

    2-2 hardware installation procedure coral ipx office installation manual si te inspection 2 5. Verify that ventilation of the installation area is capable of maintaining an ambient temperature of 32 °-104°f (0°-40°c), and a relative humidity of 20-80% non-condensing, considering the system nominal h...

  • Page 47

    Coral ipx office installation manual hardware installation procedure 2-3 si te inspection 2 17. Sufficient space must be reserved for a technician's desk or work table. Table 2-1 coral ipx office dimensions table 2-2 coral ipx office weights table 2-3 coral ipx office space requirements item dimensi...

  • Page 48

    2-4 hardware installation procedure coral ipx office installation manual si te inspection 2 figure 2-1 coral ipx office main unit sizes figure 2-2 coral ipx office expansion unit sizes and weights figure 2-3 coral ipx office space requirements (from side panels) 19" (48cm) 17.7" (45cm) 3.5" (9cm) ip...

  • Page 49

    Coral ipx office installation manual hardware installation procedure 2-5 si te inspection 2 figure 2-4 coral ipx office space requirements (from front and rear panels) 36" (100cm) 36" (100cm) minimum required clear floor space minimum required clear floor space 18.1" - 25.2" 46cm - 64cm space betwee...

  • Page 50: Electrical Requirements

    2-6 hardware installation procedure coral ipx office installation manual si te inspection 2 00 general requirements the coral ipx office operates from a standard wide input of 100 to 240vac, 47 to 63hz source or from a –40 to –56vdc source. 1. Verify that electrical service is sufficient and located...

  • Page 51

    Coral ipx office installation manual hardware installation procedure 2-7 si te inspection 2 4. Caution: this equipment is designed to permit connection between the grounded conductor of the dc supply circuit and the grounding conductor at the equipment. See installation instructions below. 5. The eq...

  • Page 52: Notes:

    2-8 hardware installation procedure coral ipx office installation manual si te inspection 2 notes:.

  • Page 53: 2.2

    Coral ipx office installation manual hardware installation procedure 2-9 eq uipment insta llation 2 2.2 equipment installation the coral ipx office cage description is covered in chapter 6, general system description . The cage mounting and installation procedure includes the following stages: unpac...

  • Page 54

    2-10 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 0 1. Inspect the shipping container for evidence of physical damage or mishandling. Report any damage to the carrier immediately. 2. If it is necessary to make a damage claim to the carrier, do not m...

  • Page 55

    Coral ipx office installation manual hardware installation procedure 2-11 eq uipment insta llation 2 table 2-5 part list (items per ipx office main unit) item description quantity main unit (ipx office * ), including one mcb office card * for items included with ipx office expansion unit, see table ...

  • Page 56

    2-12 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 table 2-6 part list (items per ipx office expansion unit) item description quantity expansion unit (ipx office * ) * for items included with ipx office main unit, see table 2-5 . For items included w...

  • Page 57

    Coral ipx office installation manual hardware installation procedure 2-13 eq uipment insta llation 2 0 the process of mounting and installing the unit includes the following stages: checking the space and positioning requirements checking the electrical requirements checking the space and positionin...

  • Page 58

    2-14 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 0 this section describes how to install the front section cards if they have not already been installed by the manufacturer. Perform the relevant section of any card that has not yet been installed. ...

  • Page 59

    Coral ipx office installation manual hardware installation procedure 2-15 eq uipment insta llation 2 0 for units mounted onto a rack, skip to mounting the office onto a rack, page 2-16 . To mount the unit onto a table: 1. Peel off five rubber bumpers provided and affix them onto the bottom panel of ...

  • Page 60

    2-16 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 0 0000 the ipx office is supplied to the field with the front rack-mounting brackets attached to the unit. These brackets are designed to fit the unit onto a 19” rack. If the unit is to be mounted on...

  • Page 61

    Coral ipx office installation manual hardware installation procedure 2-17 eq uipment insta llation 2 mounting the unit onto the rack 1. Verify the unit mounting position on the rack. See space requirements, page 2-2 . 2. Grasp each end of the unit and lift it to the mounting position on the rack. 3....

  • Page 62

    2-18 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 dismounting the ipx office unit from the rack 1. Turn off the on/off switch on the ps office unit. 2. Do one of the following: for dc powered systems, shut down the facilities power supply unit that ...

  • Page 63

    Coral ipx office installation manual hardware installation procedure 2-19 eq uipment insta llation 2 figure 2-9 removing ipx office unit from rack 2 1 unfasten screws from front bracket remove unit from rack.

  • Page 64: Ground Wiring

    2-20 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 0 to ensure adequate protection from interference by rf energy, electrical impulse noise, and lightening or power line surge, the building electrical ground point must comply with grounding recommend...

  • Page 65

    Coral ipx office installation manual hardware installation procedure 2-21 eq uipment insta llation 2 connecting the ground wire to the unit the cage ground connection includes one serrated washer, a flat washer, and one hexagonal nut assembled on the terminal connection. See figure 2-10 . Connect th...

  • Page 66

    2-22 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 connecting the ground wires to the master ground a master ground must be included within the system. See figure 2-11 , figure 2-12 and figure 2-13 . The system ground connection is fabricated as foll...

  • Page 67

    Coral ipx office installation manual hardware installation procedure 2-23 eq uipment insta llation 2 5. Connect the unit ground wire to the master ground unit as follows: a. Unfasten one of the 10-32 unf screws connected to the master ground unit and retain the screw and serrated washer. See figure ...

  • Page 68

    2-24 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-13 system ground connection with main and two expansion units master ground r=1.0 ohm max. Building entrance ground main unit customer supplied mdf expansion cage 1 10 awg stranded wires wit...

  • Page 69

    Coral ipx office installation manual hardware installation procedure 2-25 eq uipment insta llation 2 0 this section describes how to strap the shorting plugs of the various jumpers. In the coral ipx office system, some of the peripheral cards include jumpers that configure the shared service functio...

  • Page 70

    2-26 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 0. 0 general guidelines 1. Connect a static dissipating wrist strap connector (not provided by the manufacturer) to the cage and put on the strap. See figure 2-14 . Figure 2-14 esd strap connection t...

  • Page 71

    Coral ipx office installation manual hardware installation procedure 2-27 eq uipment insta llation 2 inserting a peripheral card into the main unit table 2-7 lists the peripheral interface card types that may be inserted into each card slot in the coral ipx office system. Peripheral interface cards ...

  • Page 72

    2-28 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 2. If ipx 500x expansion cages are installed, determine the position of peripheral interface cards that will be inserted into card slots 1 through 10 in the expansion cage. Observe any order previous...

  • Page 73

    Coral ipx office installation manual hardware installation procedure 2-29 eq uipment insta llation 2 4. If flexicom 200 cslx cabinets are installed, determine the position of peripheral interface cards that will be inserted into card slots 1 through 3 in the expansion cages. Observe any order previo...

  • Page 74

    2-30 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 card placement diagrams figure 2-15 through figure 2-24 may be used as a worksheet by the system designer to establish card placement prior to installation. Refer to the chapter 2 of the specific cor...

  • Page 75

    Coral ipx office installation manual hardware installation procedure 2-31 eq uipment insta llation 2 figure 2-15 coral ipx office main unit card placement figure 2-16 coral ipx office 1st expansion unit card placement figure 2-17 coral ipx office 2nd expansion unit card placement slots #4 & 5 slots ...

  • Page 76

    2-32 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-18 1st expansion cage ipx 500x card placement 1 62 7 3 84 9 5 10 card type: card type: card type: card type: card type: card type: card type: .............. .............. .............. ......

  • Page 77

    Coral ipx office installation manual hardware installation procedure 2-33 eq uipment insta llation 2 figure 2-19 2nd expansion cage ipx 500x card placement 1 62 7 3 84 9 5 10 card type: card type: card type: card type: card type: card type: card type: .............. .............. .............. ......

  • Page 78: Note:

    2-34 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-20 1st expansion cage ipx 800x card placement s hel f# 2 ju m per s p rm . Sy nc . Sl o t# 4 se c. Sy nc . S lo t# 5 j37 di g it a l t run k (s ee c hapt er 10) 1 2 3 4 5 6 7 8 9 10 11 12 co...

  • Page 79

    Coral ipx office installation manual hardware installation procedure 2-35 eq uipment insta llation 2 figure 2-21 2nd expansion cage ipx 800x card placement 1 2 3 4 5 6 7 8 9 10 11 12 card type: card type: card type: card type: card type: card type: card type: card type: .............. .................

  • Page 80

    2-36 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-22 system with one flexicom 200 expansion unit universal i/o card type.............................................. Universal i/o card type.............................................. Sha...

  • Page 81

    Coral ipx office installation manual hardware installation procedure 2-37 eq uipment insta llation 2 figure 2-23 1st flexicom 200 cabinet in a system with two expansion cabinets universal i/o card type.............................................. Universal i/o card type................................

  • Page 82

    2-38 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-24 2nd flexicom 200 cabinet in a system with two expansion cabinets universal i/o card type.............................................. Universal i/o card type................................

  • Page 83

    Coral ipx office installation manual hardware installation procedure 2-39 eq uipment insta llation 2 0 this section describes how to interconnect the units within the coral ipx office system. For a full description of the different system configurations, see ipx office and ipx expansion unit install...

  • Page 84

    2-40 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 3. Plug the pin-type connector of the ipx office expansion cable into the pin-type receptacle on the front panel of the esim office peripheral card. 4. Plug the ribbon-type connector of the ipx offic...

  • Page 85

    Coral ipx office installation manual hardware installation procedure 2-41 eq uipment insta llation 2 connecting the first expansion cage to the second expansion cage 1. Plug the male end of the h500-1 cable into the female d-type connector labeled to second expansion unit located in the top section ...

  • Page 86

    2-42 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 defining expansion cage numbers ipx office cage numbers are defined automatically and require no strapping. For information on ipx 500x, 800x cages, and flexicom 200 cslx cabinets, see figure 2-18 th...

  • Page 87

    Coral ipx office installation manual hardware installation procedure 2-43 eq uipment insta llation 2 00 this section describes how to install the dc power supply card into its slot. The ipx office unit is shipped from the manufacturer with the ac power supply installed. If a dc power supply is to be...

  • Page 88

    2-44 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-25 ps office dc front panel on + - off ps office dc cat. No. 77440950300 output: +5v 6a +3.3v 6a dc dc dc -48v 1a removable m3 screws.

  • Page 89

    Coral ipx office installation manual hardware installation procedure 2-45 eq uipment insta llation 2 0 the coral ipx office can operate as an ac powered system or as a dc powered system. For dc powered systems, skip to dc powered systems, page 2-47 . Ac powered systems this section describes how to ...

  • Page 90

    2-46 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-27 ac power connection for three ipx office units to ac power source master groud building entrance ground mdf.

  • Page 91

    Coral ipx office installation manual hardware installation procedure 2-47 eq uipment insta llation 2 dc powered systems this section describes how to connect the power wires to the coral ipx office unit for dc powered systems (that is, when the ps office dc power supply card is installed in the unit...

  • Page 92

    2-48 hardware installation procedure coral ipx office installation manual eq uipment insta llation 2 figure 2-28 dc power wiring for one ipx office unit figure 2-29 dc power wiring for three units to ac power master ground (or mdfipx ground) building entrance ground customer supplied mdf ground netw...

  • Page 93: 2.3

    Coral ipx office installation manual hardware installation procedure 2-49 pr ogram in terface device connection 2 2.3 program interface device connection the data terminal or personal computer that will be used as the program interface (pi) device must be equipped with an rs-232e asynchronous serial...

  • Page 94

    2-50 hardware installation procedure coral ipx office installation manual pr ogram interface device connection 2 figure 2-30 9-pin program interface device connections to kb0 kb0 programming port (use female cable 9 pin connector) data terminal ready - 4 6 9 carrier detect - 1 receive data - 2 trans...

  • Page 95: Chapter

    Coral ipx office installation manual chapter 3 initial power-up tests 3.1 power supply test.......................................................................3-1 3.2 common control test..................................................................3-5 3.3 identifying the coral expansion units...

  • Page 97: 3.1

    Coral ipx office installation manual initial power-up tests 3-1 po wer s upply t est 3 3.1 power supply test this chapter provides information about connecting the power supply to the facilities power supply. The ipx office can operate as an ac powered system or as a dc powered system. For ac powere...

  • Page 98

    3-2 initial power-up tests coral ipx office installation manual po wer s upply t est 3 9. Perform the ac power supply test for expansion cages as described in chapter 3 of the coral ipx 500 installation procedure and hardware reference manual or coral ipx 800 installation procedure and hardware refe...

  • Page 99: Dc Powered Systems

    Coral ipx office installation manual initial power-up tests 3-3 po wer s upply t est 3 0 1. Verify that the cage ground wire is connected and the ground nut is tightened. See ground wiring, page 2-20 . 2. Verify that the ps office dc unit has been installed and the two removable screws on the left a...

  • Page 100

    3-4 initial power-up tests coral ipx office installation manual po wer s upply t est 3 figure 3-2 ipx office unit dc power connections to ac power master ground (or mdfipx ground) building entrance ground customer supplied mdf ground network termination ground r=1.0 ohm max. Circuit breaker 30a 250v...

  • Page 101: 3.2

    Coral ipx office installation manual initial power-up tests 3-5 co mm on c ont ro l t est 3 3.2 common control test this section deals with the common control test. This test checks that the system has initialized properly and that the memory lithium battery is functional. 0 control card initializat...

  • Page 102

    3-6 initial power-up tests coral ipx office installation manual co mm on c ont ro l t est 3 8. On the front panel of the ipx office unit (see figure 6-3 on page 6-3 ), verify that the led indicators appear as follows: green power led indicator turns on. Red gc led indicator turns on until the system...

  • Page 103

    Coral ipx office installation manual initial power-up tests 3-7 co mm on c ont ro l t est 3 custom init code... Checking prog-mem prog-mem is o.K checking coding memory coding memory is o.K. End checking coding memory checking mcb office controls end checking mcb office controls checking sau # end c...

  • Page 104

    3-8 initial power-up tests coral ipx office installation manual co mm on c ont ro l t est 3 3. Do one of the following: if the second message appears, the system has initialized properly and is capable of processing calls. The version number of the generic feature software is indicated where the x's...

  • Page 105

    Coral ipx office installation manual initial power-up tests 3-9 co mm on c ont ro l t est 3 0 if the start-up tests detect that the voltage level of a lithium backup battery on the mcb office is insufficient to reliably maintain the memory contents in the event of power failure, the following messag...

  • Page 106: Notes:

    3-10 initial power-up tests coral ipx office installation manual co mm on c ont ro l t est 3 notes:.

  • Page 107: 3.3

    Coral ipx office installation manual initial power-up tests 3-11 id entifying th e coral expan sion un its 3 3.3 identifying the coral expansion units this section describes how to identify the expansion units connected to the coral ipx office system. Table 3-1 defines the minimum software version r...

  • Page 108

    3-12 initial power-up tests coral ipx office installation manual id entifying th e coral expan sion un its 3 0 before the peripheral cards can be installed and the system initialized, it is necessary for the coral system to identify each unit or cage within the system. Therefore, the following proce...

  • Page 109: 3.4

    Coral ipx office installation manual initial power-up tests 3-13 peripheral interface car d initialization 3 3.4 peripheral interface card initialization this section describes how to initialize the peripheral cards. Perform this section only after the coral ipx office has been initialized properly ...

  • Page 110

    3-14 initial power-up tests coral ipx office installation manual peripheral interface car d initialization 3 rules for inserting a coral circuit card 1. Connect a static dissipating wrist strap connector to the cage and put on the strap. See figure 2-14 on page 2-26 . 2. To insert a circuit card com...

  • Page 111

    Coral ipx office installation manual initial power-up tests 3-15 peripheral interface car d initialization 3 5. Attach the program interface (pi) device cable to the kb0 programming port connector on the front panel of the ipx office unit if not already attached. The installation of shared service a...

  • Page 112

    3-16 initial power-up tests coral ipx office installation manual peripheral interface car d initialization 3 cdb ........................ Allows modifying the card database set assigned by the system. When not applicable for the card, --- is displayed in this field. Version/subversion . Provides inf...

  • Page 113

    Coral ipx office installation manual initial power-up tests 3-17 peripheral interface car d initialization 3 table 3-2 card slot status messages . Message description recommendations active initialization was successfully completed. None active/p card is partially active because there are not enough...

  • Page 114: System Initialization

    3-18 initial power-up tests coral ipx office installation manual peripheral interface car d initialization 3 0 preparing for initialization after the software has been installed and initialized: 1. In the expansion cages, verify that the power supply switch is in the off position (turned downwards)....

  • Page 115

    Coral ipx office installation manual initial power-up tests 3-19 peripheral interface car d initialization 3 ipx office main unit initialization 1. Verify that the mcb office control card has been initialized properly as defined by the front panel led indicators. See table 6-1 on page 6-4 . 2. Inser...

  • Page 116

    3-20 initial power-up tests coral ipx office installation manual peripheral interface car d initialization 3 first expansion cage or cabinet initialization 1. Turn on the power supply unit in the first expansion cage. 2. On the front panel of the power supply unit, verify that the green power indica...

  • Page 117: 3.5

    Coral ipx office installation manual initial power-up tests 3-21 i/ o ca ble installa tion 3 3.5 i/o cable installation the i/o cables are connected to the cage after all the corresponding cards are in place. 1. Determine the route of input/output (i/o) cables from the mdf to the i/o connectors of t...

  • Page 118

    3-22 initial power-up tests coral ipx office installation manual i/ o ca ble installa tion 3 direct pinout of the champ/card connection, page 5-26 or direct pinout of the block 66 mdf connection, page 5-29 . 8. For information on protection devices, refer to protection devices, page 5-13 for the sur...

  • Page 119: 3.6

    Coral ipx office installation manual initial power-up tests 3-23 c ompl eti ng th e ins tal la ti on 3 3.6 completing the installation 1. Remove any other items from the shipping containers. 2. Remove all empty packages, crates, and debris. 3. Verify that you have provided all of the necessary instr...

  • Page 120: Notes:

    3-24 initial power-up tests coral ipx office installation manual c ompl eti ng th e ins tal la ti on 3 notes:.

  • Page 121: Chapter

    Coral ipx office installation manual chapter 4 software installation procedure 4.1 generic feature software ...........................................................4-1 4.2 system database control............................................................4-7.

  • Page 123: 4.1

    Coral ipx office installation manual software installation procedure 4-1 generic featur e softwar e upgrade 4 4.1 generic feature software upgrade 0 the coral ipx office is delivered to the site with factory-loaded software on the imc8 card. The imc8 card is an 8mb flash memory card. See imc8 flash ...

  • Page 124

    4-2 software installation procedure coral ipx office installation manual generic featur e softwar e upgrade 4 0 0 use fmprog version 6.Xx and above. Otherwise, the coral will not initialize. The upgrade of the generic feature software involves the following main steps: installing the fmprog-utility ...

  • Page 125

    Coral ipx office installation manual software installation procedure 4-3 generic featur e softwar e upgrade 4 0 this section provides instructions on inserting the imc8 flash memory card after it has been programmed with a new or upgraded software version. Creating a binary backup of the database be...

  • Page 126

    4-4 software installation procedure coral ipx office installation manual generic featur e softwar e upgrade 4 the second message may appear after two or three minutes, following several short messages that appear during system start-up: ccs is on the air...... (root) ccs xx.Xx.Xx copyright (c) 2001-...

  • Page 127

    Coral ipx office installation manual software installation procedure 4-5 generic featur e softwar e upgrade 4 0 the universal gateway (ugw) software is embedded on the mcb office card. To upgrade the embedded application software, see the control card installation manual, chapter 6 (map). In the pi ...

  • Page 128: Notes:

    4-6 software installation procedure coral ipx office installation manual generic featur e softwar e upgrade 4 notes:.

  • Page 129: 4.2

    Coral ipx office installation manual software installation procedure 4-7 system database contr ol 4 4.2 system database control during normal system operation, the configuration database may be saved to a file on the imc8 card for permanent storage. The system may also be programmed to save the data...

  • Page 130: Saving to Imc8

    4-8 software installation procedure coral ipx office installation manual system database contr ol 4 0 the database save feature allows the system database to be copied to imc8 at any time. The procedure is as follows: 1. Verify that the system time and date are correct (press control-t to check). Up...

  • Page 131

    Coral ipx office installation manual software installation procedure 4-9 system database contr ol 4 when the flash memory space is insufficient for saving the database (dbs), the following message will appear: no space for saving data base when at least one of the flags cannot be recognized, the fol...

  • Page 132

    4-10 software installation procedure coral ipx office installation manual system database contr ol 4 0 a system database stored in imc8 can be loaded into the database memory on the mcb office card at any time. Loading the database from imc8 generally takes several minutes. During this process, the ...

  • Page 133

    Coral ipx office installation manual software installation procedure 4-11 system database contr ol 4 4. If you type y, the system goes through the following retrieval condition check sequence: a. Verify that the internal flags are present in the database to be loaded. B. Verify that the database is ...

  • Page 134: Show File Information

    4-12 software installation procedure coral ipx office installation manual system database contr ol 4 0 this option displays the list of backed up files stored on the imc8 card. From the database flash menu, press 2 to display the list of backed up files. The following prompt appears: execute (y/n)? ...

  • Page 135: Automatic Daily Backup

    Coral ipx office installation manual software installation procedure 4-13 system database contr ol 4 0 the system configuration database can be automatically saved to a database file on the imc8 at a preset time each day. Use autobackup to automatically save the database. During automatic daily back...

  • Page 136: Erasing Flash Memory

    4-14 software installation procedure coral ipx office installation manual system database contr ol 4 0 this function enables erasing of backed up files stored on the imc8 card: 1. From the database menu, press 4 to erase the flash memory. The following prompt appears: proceed with erase (0/1/a/n/) ?...

  • Page 137: Chapter

    Coral ipx office installation manual chapter 5 external connections 5.1 main distribution frame (mdf) ...................................................5-1 5.2 external equipment .....................................................................5-7 5.3 protection devices............................

  • Page 139: 5.1

    Coral ipx office installation manual external connections 5-1 main distribu tion fra m e ( m df) 5 5.1 main distribution frame (mdf) 0 this chapter describes the mdf and the pinout connections to the cage and external equipment. For hardware installation instructions, refer to chapter 2, hardware in...

  • Page 140: Tip:

    5-2 external connections coral ipx office installation manual main distribu tion fra m e ( m df) 5 therefore, care should be taken to plan the mdf layout before fastening components to the rack or table-mounted surface, such as: network (lan/wan) connection trunk circuits wired and wireless station ...

  • Page 141

    Coral ipx office installation manual external connections 5-3 main distribu tion fra m e ( m df) 5 table 5-1 external i/o connectors for coral ipx office peripheral cards card name number of connectors card slot champ rj-45 special 8/16/24sft office 1 - - 2-3, 4-5 4/8sa office 1 - - 16sa office (8sa...

  • Page 142

    5-4 external connections coral ipx office installation manual main distribu tion fra m e ( m df) 5 figure 5-1 connecting via an mdf esix office - - expansion cables 6-7 exp. 30t office (30t or 30tm) - 1 - 8-9, 10-11 4tbr office - 4 - pri-30 office - 1 - udt office (t1 or pri-23) - 1 - 4t office - 4 ...

  • Page 143

    Coral ipx office installation manual external connections 5-5 main distribu tion fra m e ( m df) 5 the importance of proper tip and ring wiring due to the high speed digital signaling over the wire pair, it is important to verify that the wiring is free of potential problems. The wire pair feeding t...

  • Page 144: Notes:

    5-6 external connections coral ipx office installation manual main distribu tion fra m e ( m df) 5 notes:.

  • Page 145: 5.2

    Coral ipx office installation manual external connections 5-7 external equipment 5 5.2 external equipment 0 this section discusses the station equipment used with the coral ipx office including both wired, wireless, and voip stations. Wired stations each station peripheral card provides an i/o champ...

  • Page 146

    5-8 external connections coral ipx office installation manual external equipment 5 to prevent a potential shock hazard to station users and damage to the system, make sure that station circuits extended over cables that exit the building are adequately protected from lightning and surge currents. Se...

  • Page 147

    Coral ipx office installation manual external connections 5-9 external equipment 5 figure 5-3 modular wired station jack wiring diagram 6 5 4 3 2 1 pin 2 black dt (dtr), flexset/dkt + 48vdc pin 2 black dt (dtr), flexset/dkt + 48vdc pin 2 black dt (dtr), flexset/dkt + 48vdc pin 3 red ar (drt), [r] pi...

  • Page 148

    5-10 external connections coral ipx office installation manual external equipment 5 wireless and voip stations the flexair handset and the voip endpoints are not connected via the mdf . Related documentation for further information about coral voice terminals not covered by this section, consult the...

  • Page 149: Trunk Circuits

    Coral ipx office installation manual external connections 5-11 external equipment 5 generally, trunk circuits are connected to the coral ipx office system simply by connecting the trunk interface circuit of a coral ipx office trunk card to the point of demarcation where the trunk circuits from the t...

  • Page 150: Auxiliary Connections

    5-12 external connections coral ipx office installation manual external equipment 5 table 5-3 lists the auxiliary connectors (located on the peripheral cards) and their functions. Table 5-3 auxiliary connectors ............................................................................................

  • Page 151: 5.3

    Coral ipx office installation manual external connections 5-13 pr otection devices 5 5.3 protection devices 0 this section describes the primary and secondary protection devices used with the coral ipx office system and how they are installed. . Lightning and over-voltage arrestors are used to prote...

  • Page 152

    5-14 external connections coral ipx office installation manual pr otection devices 5 primary protection absorbs the major impact of infrequent, but dangerous, catastrophic surges, while secondary protection suppresses constantly occurring impulses. These impulses, while not dangerous, can cripple va...

  • Page 153

    Coral ipx office installation manual external connections 5-15 pr otection devices 5 table 5-5 telephone circuit secondary protection device specifications device type specification measurement surge/impulse protector clamp points dc. 2kv/s 100v/ µ s 10kv/ µ s 230vdc max. 230vdc max. 100vdc max 30vd...

  • Page 154: Surge Arrestor Magazine

    5-16 external connections coral ipx office installation manual pr otection devices 5 to prevent serious damage to the coral ipx office system, the analog trunk and station circuits whose cables are laid outside the building, must be protected from the electrical peaks caused by lightning. Magazine 1...

  • Page 155: 5.4

    Coral ipx office installation manual external connections 5-17 power fail (pf) tr ans fer ci rc ui ts 5 5.4 power fail (pf) transfer circuits with the installation of trunk cards to support the pf (power fail) transfer option, four trunks per trunk card may be directed to station sets if power to th...

  • Page 156: Database Programming

    5-18 external connections coral ipx office installation manual power fail (pf) t ransfer cir cuits 5 0 to use the power fail transfer features of the coral system, the station dial numbers, to which power fail trunks are transferred, must be entered in the system database. Refer to power fail trunk ...

  • Page 157: 5.5

    Coral ipx office installation manual external connections 5-19 data commu nicatio n ports rs- 232e 5 5.5 data communication ports rs-232e the coral ipx office switching system is capable of switching digital data information as well as voice signals. Coral ipx office system data communication device...

  • Page 158

    5-20 external connections coral ipx office installation manual data commu nicatio n ports rs- 232e 5 figure 5-7 flexset 80 / 280s / 281s / apdl / apa or pex+apa rs-232e (v.24) pinout 9 6 8 7 6 5 4 3 2 1 9 8 7 6 5 4 3 2 1 data terminal ready (dtr) transmit data (tr) receive data (rd) data carrier det...

  • Page 159: 5.6

    Coral ipx office installation manual external connections 5-21 i/ o car d connect ions for coral peripheral interface car ds 5 5.6 i/o card connections for coral peripheral interface cards 0 the following tables list the pinout connection directly on the champ/card connection for all currently avail...

  • Page 160

    5-22 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 24sft office 1 x champ 2-3, 4-5 table 5-9 on page 5-27 and table 5-12 on page 5-30 30t office (30t or 30tm) 1 x rj-45 8-9, 10-11 table 5-19 on page 5-38 4s office 1 x champ ...

  • Page 161

    Coral ipx office installation manual external connections 5-23 i/ o car d connect ions for coral peripheral interface car ds 5 8sa+16fx office 1 x champ 2-3, 4-5 table 5-10 on page 5-28 and table 5-13 on page 5-31 8sa+8fx office 1 x champ 2-3, 4-5 table 5-10 on page 5-28 and table 5-13 on page 5-31 ...

  • Page 162

    5-24 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 wan (mcb office) 1 x rj-45 unit front panel table 5-20 on page 5-42 external i/o connectors pinout card name connector card slot table/page.

  • Page 163: Champ Connections

    Coral ipx office installation manual external connections 5-25 i/ o car d connect ions for coral peripheral interface car ds 5 0 the following tables list the pinout, the wire colors, and the signals of the i/o champ connectors for each station card and each optional connection. Table 5-7 peripheral...

  • Page 164

    5-26 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 direct pinout of the champ/card connection table 5-8 displays the pinout connection directly on the champ/card connection for the 4sa office, 8sa office, 16sa office, 24sa o...

  • Page 165

    Coral ipx office installation manual external connections 5-27 i/ o car d connect ions for coral peripheral interface car ds 5 table 5-9 displays the pinout connection directly on the champ/card connection for the 8sft office, 16sft office, and 24sft office peripheral cards. Table 5-9 champ 50 conne...

  • Page 166

    5-28 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 table 5-10 displays the pinout connection directly on the champ/card connection for the 4sa+8fx office, 4sa+16fx office, 8sa+8fx office, 8sa+16fx office, 4s+8fx office, 4s+1...

  • Page 167

    Coral ipx office installation manual external connections 5-29 i/ o car d connect ions for coral peripheral interface car ds 5 direct pinout of the block 66 mdf connection table 5-11 displays the pinout connection on the block 66 mdf connection for the 4sa office, 8sa office, 16sa office, 24sa offic...

  • Page 168

    5-30 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 table 5-12 displays the pinout connection on the block 66 mdf connection for the 8sft office, 16sft office, and 24sft office peripheral cards. Table 5-12 block 66 mdf pinout...

  • Page 169

    Coral ipx office installation manual external connections 5-31 i/ o car d connect ions for coral peripheral interface car ds 5 table 5-13 displays the pinout connection on the block 66 mdf connection for the 4s+8fx office, 4s+16fx office, 8s+8fx office and 8s+16fx office peripheral cards. Table 5-13...

  • Page 170: Rj-45 Connections

    5-32 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 0 peripheral cards index the i/o connections of the following interface cards are performed via cables connected to their rj-45 connectors . ...................................

  • Page 171

    Coral ipx office installation manual external connections 5-33 i/ o car d connect ions for coral peripheral interface car ds 5 4t office and 4t-cid office cards the external network connections to the 4t office and 4t-cid office circuit card are made via four rj-45 telephony connectors on the front ...

  • Page 172

    5-34 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 8t office and 8t-cid office cards the external network connections to the 8t office and 8t-cid office circuit card are made via eight rj-45 telephony connectors on the front...

  • Page 173

    Coral ipx office installation manual external connections 5-35 i/ o car d connect ions for coral peripheral interface car ds 5 4tbr office card the external network connections to the 4tbr office digital circuit card are made via four rj-45 telephony connectors on the front panel. See table 5-16 and...

  • Page 174

    5-36 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 udt office (t1 or pri-23) the external network connections to the udt office (t1 or pri-23, jumper selection) digital circuit are made via the rj-45 telephony connector on t...

  • Page 175

    Coral ipx office installation manual external connections 5-37 i/ o car d connect ions for coral peripheral interface car ds 5 pri-30 office the external network connections to the pri-30 office digital circuit are made via the rj-45 telephony connector on the front panel. See table 5-18 and figure ...

  • Page 176

    5-38 external connections coral ipx office installation manual i/ o car d connect ions for coral peripheral interface car ds 5 30t office card (30t or 30tm) the external network connections to the 30t office digital circuit are made via the rj-45 telephony connector on the front panel. See table 5-1...

  • Page 177: 5.7

    Coral ipx office installation manual external connections 5-39 lan, w a n, and printer conn ection s 5 5.7 lan, wan, and printer connections 0 this section describes how to connect lan, wan, and a printer to the coral office main unit. The coral ipx office main unit includes: eight rj-45 ports for c...

  • Page 178: Connecting to The Lan

    5-40 external connections coral ipx office installation manual lan, w a n, and printer conn ection s 5 0 the coral ipx office connects directly to the lan whether or not an ntu office card is supplied with the system. A switching device can be added, allowing additional ip endpoints to be cascaded w...

  • Page 179: Connecting to A Printer

    Coral ipx office installation manual external connections 5-41 lan, w a n, and printer conn ection s 5 0m the coral ipx office can function as a printer server when an ntu office card is supplied with the system. Connecting to a printer when an ntu office card is supplied if an ntu office card is su...

  • Page 180: Lan/wan Pinout

    5-42 external connections coral ipx office installation manual lan, w a n, and printer conn ection s 5 00 table 5-20 and figure 5-17 show the interface connections of the pins on the lan/wan rj-45 connector to the network and ip endpoints. Table 5-20 lan/wan pinout figure 5-17 lan/wan pinout for inf...

  • Page 181: Chapter

    Coral ipx office installation manual chapter 6 system description 6.1 general system description..............................................................6-1 6.2 system configuration options.........................................................6-25 00

  • Page 183: 6.1

    Coral ipx office installation manual system description 6-1 general system descriptio n 6 6.1 general system description this chapter describes the ipx office unit components. Upon completing this section, you will be familiar with unit components. The instructions for installing the unit are found ...

  • Page 184

    6-2 system description coral ipx office installation manual general system descriptio n 6 figure 6-1 front view of the table-mounted ipx office unit figure 6-2 front view of the rack-mounted ipx office unit rear side side panel front panel side panel exhaust fans.

  • Page 185

    Coral ipx office installation manual system description 6-3 general system descriptio n 6 front panel the front panel of the main unit includes eight diagnostic led indicators, a slot for a memory card, a compact flash disk, a kb0 port, a ugw port, eight lan ports, one wan port, one printer server p...

  • Page 186

    6-4 system description coral ipx office installation manual general system descriptio n 6 table 6-1 front panel features feature what is it for? Power led (green - continuously on) system power is on and functional gc act. Led (green - flashes) * group controller functional mrc led (green - continuo...

  • Page 187

    Coral ipx office installation manual system description 6-5 general system descriptio n 6 rear side the rear side of the unit houses the peripheral cards and the power supply card. See figure 6-5 . When installed, the front panels of the peripheral cards and the power supply card completely overlay ...

  • Page 188

    6-6 system description coral ipx office installation manual general system descriptio n 6 the rear side is designed to house full-size as well as half-size cards. See peripheral card description, page 10-5 . The front panel of the half-size cards come in three different sizes. For that reason, some ...

  • Page 189

    Coral ipx office installation manual system description 6-7 general system descriptio n 6 figure 6-6 left panel of the ipx office main unit figure 6-7 right panel of the ipx office main unit top side the top side is part of the cover. No space needs to be maintained above the unit cover for maintena...

  • Page 190: Unit Cover

    6-8 system description coral ipx office installation manual general system descriptio n 6 0 the unit cover protects internal circuitry during normal operation from damage and rfi while still allowing access to the interior for maintenance activities. The cover also enables forced convection cooling ...

  • Page 191

    Coral ipx office installation manual system description 6-9 general system descriptio n 6 opening the unit cover 1. Verify that the on/off switch on the ps office unit is turned off. 2. Remove the ac power cord or dc wires from the ps office unit. 3. Disconnect any cables attached to the front panel...

  • Page 192

    6-10 system description coral ipx office installation manual general system descriptio n 6 closing the unit cover 1. Verify that all control cards and the ntu office card are properly installed, that all internal cables are properly connected, and that the ntu office card on/off switch is turned on....

  • Page 193: Unit Interior

    Coral ipx office installation manual system description 6-11 general system descriptio n 6 0000 0 the unit interior is different for the main unit and the expansion unit. Main unit the front and rear section of the main unit is displayed in figure 6-12 . Figure 6-12 ipx office main unit interior the...

  • Page 194

    6-12 system description coral ipx office installation manual general system descriptio n 6 mcb office card the mcb office card is the main control card of the ipx office unit. It is attached to on the bottom surface of the ipx office chassis on the front section and is connected to the mbp office. T...

  • Page 195

    Coral ipx office installation manual system description 6-13 general system descriptio n 6 expansion unit the front and rear section of the expansion unit is displayed in figure 6-13 . The expansion unit does not include any components in the front section. The led office card on the front panel is ...

  • Page 196: Rear Section

    6-14 system description coral ipx office installation manual general system descriptio n 6 0 0 the rear section of the unit interior includes the peripheral card slots and the power supply slot. The slots are aligned horizontally from top to bottom. The top two slots (slot 2-3 and slot 4-5) house fu...

  • Page 197

    Coral ipx office installation manual system description 6-15 general system descriptio n 6 peripheral cards the ipx office unit includes five peripheral card slots in the rear section. These card types are described in chapter 10, peripheral cards , and in greater detail in the coral service and per...

  • Page 198

    6-16 system description coral ipx office installation manual general system descriptio n 6 blank panels blank panels are used to cover peripheral card slots that are not occupied by a peripheral card. The blank panel covers the slot, blocking the insertion of foreign objects into the system, thus pr...

  • Page 199

    Coral ipx office installation manual system description 6-17 general system descriptio n 6 other disadvantages of not covering an empty slot with a panel, include: rendering the system susceptible to rfi disturbances increasing the risk of damage to the system caused by the influx of electrostatical...

  • Page 200: Heat Removal

    6-18 system description coral ipx office installation manual general system descriptio n 6 0 heat is removed from the ipx office unit by forced convection. Three dc fans, mounted on the inside of the right panel, draw cool, ambient air from the left side of the unit. The cool air absorbs the heat fr...

  • Page 201

    Coral ipx office installation manual system description 6-19 general system descriptio n 6 cooling fans the unit includes fans mounted inside the left panel of the unit. They draw cool ambient air in from the right panel of the unit that cools the internal components of the ipx office unit and then ...

  • Page 202

    6-20 system description coral ipx office installation manual general system descriptio n 6 removing a fan 1. Open the unit cover. See figure 6-18 and opening the unit cover, page 6-9 . 2. Remove the fan power wires from its connector on the mbp office. 3. Release the top fan plugs from the fan and t...

  • Page 203

    Coral ipx office installation manual system description 6-21 general system descriptio n 6 installing a new fan 1. Insert the rubber plugs into the bottom mounting holes of the fan. See figure 6-19 . 2. Slip the fan plug assembly into the mating openings on the unit. 3. Insert the top rubber plug th...

  • Page 204: Safety Labels

    6-22 system description coral ipx office installation manual general system descriptio n 6 0 there are five safety labels located on the ipx office unit and related equipment: the nameplate label, the ul label, the electrical hazard label, esd label, and the ground label. Nameplate label the namepla...

  • Page 205

    Coral ipx office installation manual system description 6-23 general system descriptio n 6 electrical hazard label the electrical hazard label is affixed to the internal surface of the power supply unit (ac and dc). It can be viewed only when the power supply is removed from the coral ipx unit. See ...

  • Page 206

    6-24 system description coral ipx office installation manual general system descriptio n 6 esd label an esd label is located on the unit cover towards the rear panel, above the grounding terminal. See figure 6-22 . The ipx office unit is not equipped with a electro-static dissipating (esd) wrist str...

  • Page 207: 6.2.

    Coral ipx office installation manual system description 6-25 sy stem configuration options ipx office 6 6.2. System configuration options ipx office 0 this section describes the layout and configuration of the ipx office system. For a general description of the ipx office units, see general system d...

  • Page 208

    6-26 system description coral ipx office installation manual sy stem configuration options ipx office 6 the main unit cage includes control cards and peripheral cards. The expansion cage or cages include peripheral cards. Main unit (ipx office) the ipx office unit houses the mbp (main backplane) off...

  • Page 209

    Coral ipx office installation manual system description 6-27 sy stem configuration options ipx office 6 table 6-4 number of universal i/o slots per system configuration figure 6-23 system with one unit (ipx office) system configuration main unit 1 st expansion cage 2 nd expansion cage total system u...

  • Page 210

    6-28 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-24 system with ipx office main unit and one ipx office expansion unit figure 6-25 system with ipx office main unit and two ipx office expansion units 4 office card i/o slots common contro...

  • Page 211

    Coral ipx office installation manual system description 6-29 sy stem configuration options ipx office 6 figure 6-26 system with two units (ipx office and ipx 500x) 4 office card i/o slots common control 1 power supply ps500 coral ipx 500x expansion 10 ipx i/o slots.

  • Page 212

    6-30 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-27 system with three units (ipx office and two ipx 500x cages) 4 office card i/o slots 2 power supplies ps500 coral ipx 500x 1st expansion common control coral ipx 500x 2nd expansion 20 i...

  • Page 213

    Coral ipx office installation manual system description 6-31 sy stem configuration options ipx office 6 figure 6-28 system with two units ipx office and ipx 800x) 4 office card i/o slots coral ipx 800x expansion 11 coral universal i/o slots 1 shared service slot 1 power supply ps19 common control.

  • Page 214

    6-32 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-29 system with three units (ipx office, ipx 500x, and ipx 800x) 1 power supply ps19 4 office card i/o slots common control 1 power supply ps500 10 ipx i/o slots coral ipx 500x 1st expansi...

  • Page 215

    Coral ipx office installation manual system description 6-33 sy stem configuration options ipx office 6 figure 6-30 system with three units (ipx office and two ipx 800x cages) coral ipx 800x 1st expansion px control card slot 4 office card i/o slots coral ipx 800 2nd expansion common control 2 power...

  • Page 216

    6-34 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-31 system with two units (ipx office and one flexicom 200 cabinet) figure 6-32 system with three units (ipx office and two flexicom 200 cabinets) common control 2 i/o slots 1 shared servi...

  • Page 217

    Coral ipx office installation manual system description 6-35 sy stem configuration options ipx office 6 0 the ipx office system can be connected in any one of the following configurations: table 6-5 ipx office system expansion options the ipx office main cage and its expansion cages maintain a conti...

  • Page 218

    6-36 system description coral ipx office installation manual sy stem configuration options ipx office 6 ipx office/ex expansion units cannot be interconnected in the same system with ipx 500x cages or ipx 800x cages or flexicom 200 cslx cabinets. Flexicom 200 cslx expansion cabinets cannot be interc...

  • Page 219

    Coral ipx office installation manual system description 6-37 sy stem configuration options ipx office 6 figure 6-33 connection between two units figure 6-34 connection between three units figure 6-35 connection between the ipx office and 500x sec prm sync esix office ip x o ffi ce e xp an si on c ab...

  • Page 220

    6-38 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-36 connection between the ipx office unit and two 500x figure 6-37 connection between the ipx office unit and the 800x cage sync sec prm esim office ipx office ps office ac cat. No. 77440...

  • Page 221

    Coral ipx office installation manual system description 6-39 sy stem configuration options ipx office 6 figure 6-38 connection between the ipx office unit, 500x and 800x cages sync sec prm esim office ps office ac cat. No. 77440950200 output: +5v 6a +3.3v 6a dc dc dc -48v 1a input: on off 100-240vac...

  • Page 222

    6-40 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-39 connection between the ipx office unit and two 800x cages sync sec prm esim office ipx office pscsxac cat. No. 77440950200 output: +5v 6a +3.3v 6a dc dc dc -48v 1a input: on off 100-24...

  • Page 223

    Coral ipx office installation manual system description 6-41 sy stem configuration options ipx office 6 figure 6-40 connection between the ipx office unit and one flexicom 200 cabinet a view a-a flexicom 200 cslx 1st expansion female male male female ipx office main.

  • Page 224

    6-42 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-41 connection between the ipx office unit and two flexicom 200 cabinets view a-a a flexicom 200 cslx 1st expansion female flexicom 200 cslx 2nd expansion male female male female male ipx ...

  • Page 225

    Coral ipx office installation manual system description 6-43 sy stem configuration options ipx office 6 0 ipx office main unit the coral ipx office main unit is a non-blocking system. The ipx office system incorporates 1024x1024 timeslots. The timeslots are distributed as follows: slots 2-3, 4-5, 8-...

  • Page 226

    6-44 system description coral ipx office installation manual sy stem configuration options ipx office 6 ipx office/ex expansion cages the ipx office expansion cage shares time slots 256-639 (384 time slots) between a maximum of 4 card slots. Slots 2-3 and 4-5, share 128 time slots. Slots 8-9 share a...

  • Page 227

    Coral ipx office installation manual system description 6-45 sy stem configuration options ipx office 6 ipx 500x/800x expansion cages both ipx 500x and/or ipx 800x cages share time slots 256-639 (384 time slots) between a maximum of 24 card slots. The timeslots are evenly divided to three groups of ...

  • Page 228

    6-46 system description coral ipx office installation manual sy stem configuration options ipx office 6 figure 6-43 pcm timeslot distribution with ipx 500x/800x cages installed a2 b2 a1 b1 a0 b0 a3 b3 a4 b4 igc peripheral service & group controller 1024 time slots ipx office main unit ipx 500x / 800...

  • Page 229

    Coral ipx office installation manual system description 6-47 sy stem configuration options ipx office 6 flexicom 200 (cslx) expansion cabinets both flexicom 200 cabinets share time slots 256-384 (128 time slots) between a maximum of six card slots. The timeslots are detailed in table 6-9 . Figure 6-...

  • Page 230

    6-48 system description coral ipx office installation manual sy stem configuration options ipx office 6 0 general the coral ipx 800x expansion cage is a small, rack-mounted extension to the ipx office, ipx 800m, or coral ipx 500m cage. It supports any of the flexicom 300,400,5000,6000 and ipx 800,30...

  • Page 231

    Coral ipx office installation manual system description 6-49 sy stem configuration options ipx office 6 when an ipx 800x expansion cage is used in an ipx office system there are situations where it is worthwhile to include an ipx 800x cage in an ipx 500 system: to allow the use of coral features not...

  • Page 232: Notes:

    6-50 system description coral ipx office installation manual sy stem configuration options ipx office 6 notes:.

  • Page 233: Chapter

    Coral ipx office installation manual chapter 7 power supply 7.1 ps office ac power supply unit.................................................7-1 7.2 ps office dc power supply unit...............................................7-13.

  • Page 235: 7.1

    Coral ipx office installation manual power supply 7-1 ps office ac power s upply unit 7 7.1 ps office ac power supply unit 0 the ps office ac power supply unit provides operating voltages for the coral ipx office main unit and expansion unit. Power source the ps office ac operates from a nominal inp...

  • Page 236

    7-2 power supply coral ipx office installation manual ps office ac power s upply unit 7 figure 7-1 ps office ac front panel ps office ac card layout the ps office ac card component side is shown in figure 7-2 . The components are described in the following table: feature description power output led...

  • Page 237

    Coral ipx office installation manual power supply 7-3 ps office ac power s upply unit 7 figure 7-2 ps office ac card layout figure 7-3 ps office ac card rear view fs1 power input fuse 5a/250v s.B. F2 intermodule fuse 5a/250v s.B. -48vdc power output led indicator ac to dc converter circuit board dc ...

  • Page 238: Circuit Description

    7-4 power supply coral ipx office installation manual ps office ac power s upply unit 7 0 the ps office ac includes an ac to dc converter to produce -48v and a dc to dc converter to produce the +5vdc and +3.3vdc operating voltages for the coral ipx office internal circuitry. All outputs are regulate...

  • Page 239

    Coral ipx office installation manual power supply 7-5 ps office ac power s upply unit 7 disconnecting the ac power cord from the ac power mains disconnecting the ac power cord from the ac power mains will cause normal operation to discontinue. However, the best way to disable the output voltages is ...

  • Page 240: Installation and Activation

    7-6 power supply coral ipx office installation manual ps office ac power s upply unit 7 0 the power supply unit is inserted into the coral ipx office unit in the right side of the ipx office unit from the rear. Installing the ac power supply 1. Verify that the ipx office unit ground wire is connecte...

  • Page 241

    Coral ipx office installation manual power supply 7-7 ps office ac power s upply unit 7 activating the ac power supply 1. Verify that the cage ground wire is connected and the ground nut is tightened. See figure 2-10 . 2. Verify that the two removable screws on the left and right side of the front p...

  • Page 242

    7-8 power supply coral ipx office installation manual ps office ac power s upply unit 7 figure 7-5 ipx office ac power connections slots 2 - 3 slots 4 - 5 slots 6 - 7 slots 8 - 9 slots 10 - 11 slot 1 ps office ac cat. No. 77440950200 output: +3.3v 6a +5v 6a dc dc dc -48v 1a on input: 100-240v 2.2a 5...

  • Page 243: Troubleshooting

    Coral ipx office installation manual power supply 7-9 ps office ac power s upply unit 7 removing the power supply 1. Locate a desk or a table top. If the surface can be damaged by sharp objects, place a protective sheet of cardboard or similar material over the top surface. 2. Turn the ps office ac ...

  • Page 244

    7-10 power supply coral ipx office installation manual ps office ac power s upply unit 7 0 the ps office ac includes two fuses: if the fs1 fuse blows, replace it with an identical fuse with the same rating. See specifications, page 7-12 . If the f2 fuse blows, replace it with an identical fuse with ...

  • Page 245

    Coral ipx office installation manual power supply 7-11 ps office ac power s upply unit 7 3. Turn on the ps office ac. Either the ps office ac is malfunctioning (replace as described on installation and activation, page 7-6 ) or the problem is caused by the backplane, control cards, peripheral, or nt...

  • Page 246: Specifications

    7-12 power supply coral ipx office installation manual ps office ac power s upply unit 7 0 ps office ac power supply input:...........................................................100-240vac 47-63hz power rating: .............................................115vac / 60hz / 6a (range: 98 to 126vac)...

  • Page 247: 7.2

    Coral ipx office installation manual power supply 7-13 ps office dc power su pply unit 7 7.2 ps office dc power supply unit 0 the ps office dc card’s component side power supply unit provides internal operating voltages for the coral ipx office main unit and expansion unit. The ps office dc operates...

  • Page 248

    7-14 power supply coral ipx office installation manual ps office dc power su pply unit 7 figure 7-6 ps office dc front panel ps office dc card layout the ps office dc card’s component side is shown in figure 7-7 . The components on the card are described in the following table. On + - off ps office ...

  • Page 249

    Coral ipx office installation manual power supply 7-15 ps office dc power su pply unit 7 figure 7-7 ps office dc card layout figure 7-8 dc power supply rear view f1 f1 power input fuse 6.3v/250v s.B. Backplane connector.

  • Page 250: Circuit Description

    7-16 power supply coral ipx office installation manual ps office dc power su pply unit 7 0 figure 7-9 presents a block diagram of the ps office dc power supply. Power input section the dc input includes a passive filter, inrush current, and a power switch. The dc input is protected against reverse p...

  • Page 251

    Coral ipx office installation manual power supply 7-17 ps office dc power su pply unit 7 figure 7-9 ps office dc block diagram 6.3a/250v s.B. Power input fuse power on/off active filter passive filter - vin input: -40 to -60vdc -48vdc nom. Vrtn inrush current note: gnd backplane connector +3.3vdc +5...

  • Page 252: Installation and Activation

    7-18 power supply coral ipx office installation manual ps office dc power su pply unit 7 0 the power supply unit is inserted into the ipx office unit in slot 1. See figure 7-10 . Installing the power supply 1. Verify that the cage ground wire is connected and the ground nut is tightened. See figure ...

  • Page 253

    Coral ipx office installation manual power supply 7-19 ps office dc power su pply unit 7 activating the ps office dc 1. Verify that the unit ground wire is connected and the ground nut is tightened. See figure 7-10 . 2. Verify that the power switch is in the off position (turned downwards). 3. Verif...

  • Page 254

    7-20 power supply coral ipx office installation manual ps office dc power su pply unit 7 figure 7-10 ps office dc connection to ac power master ground (or mdfipx ground) building entrance ground customer supplied mdf ground network termination ground r=1.0 ohm max. Circuit breaker 30a 250v s.B. 10 a...

  • Page 255

    Coral ipx office installation manual power supply 7-21 ps office dc power su pply unit 7 removing the power supply 1. Locate a desk or table top. If the surface can be damaged by sharp objects, place a protective sheet of cardboard or similar material over the top surface. 2. Turn the ps office dc p...

  • Page 256: Troubleshooting

    7-22 power supply coral ipx office installation manual ps office dc power su pply unit 7 0. The ps office dc unit does not include an alarm led indicator. The front panel of the ipx office unit includes eight (8) diagnostic led indicators. For information on troubleshooting, see front panel, page 6-...

  • Page 257: Specifications

    Coral ipx office installation manual power supply 7-23 ps office dc power su pply unit 7 0 max. Ps office dc power supply power rating:.................................... -40vdc to -56vdc, 10a max. Power consumption (from mains): ............Continuous 160w outputs: ...................................

  • Page 258: Notes:

    7-24 power supply coral ipx office installation manual ps office dc power su pply unit 7 notes:.

  • Page 259: Chapter

    Coral ipx office installation manual chapter 8 common control cards 8.1 control cards ..............................................................................8-1 8.2 mcb office card..........................................................................8-5 8.3 led card..........................

  • Page 261: 8.1

    Coral ipx office installation manual common control cards 8-1 contr ol car ds 8 8.1 control cards the common control cards include the mcb office, the imc8 flash card, the compact flash disk, the mrc card, the led office card, and the dbm-x card. The mcb office card acts as a mother card to the othe...

  • Page 262

    8-2 common control cards coral ipx office installation manual contr ol car ds 8 backplane connector on the mbp office (main backplane) card and is powered via the power supply connector. Because the mcb office integrates several embedded circuits that were previously part of separate cards in earlie...

  • Page 263

    Coral ipx office installation manual common control cards 8-3 contr ol car ds 8 figure 8-1 mcb office card layout p4 p13 dbm-x connector dbm card location u141 media gateway (mrc) card location mbp office connector j3 sau j2 esim connector a d d d a a a imc8/imc16 flash memory p15 led card connector...

  • Page 264: Card Handling Procedures

    8-4 common control cards coral ipx office installation manual contr ol car ds 8 00 control card installation install control cards as described below: installing the mrc, page 8-32 inserting the imc8, page 8-38 installing the dbm card, page 8-45 .........................................................

  • Page 265: 8.2

    Coral ipx office installation manual common control cards 8-5 mcb office car d ma in contr ol boar d 8 8.2 mcb office card main control board 00 this section describes the features and functions of the mcb office main control card. The mcb office card is the control processor card for coral ipx offi...

  • Page 266

    8-6 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 universal gateway including the ugw processor and the rs-232 connector. The ugw is described in further detail in universal gateway, page 8-9 . Other components that belong to this circuit include:...

  • Page 267

    Coral ipx office installation manual common control cards 8-7 mcb office car d ma in contr ol boar d 8 figure 8-2 mcb office card layout cpu 386ex ugw processor hard disk connector kb0 release button release button ugw com hard disk (future) location u90 u31 p5 p2 p4 p13 dbm-x connector ps office co...

  • Page 268: Main Control Processor

    8-8 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 0 the main control processor (mcp) provides rs-232e kb0 programming and maintenance interface, rs-232 ugw programming and maintenance interface, a sau connection, and an imc8 flash card interface. ...

  • Page 269: Universal Gateway

    Coral ipx office installation manual common control cards 8-9 mcb office car d ma in contr ol boar d 8 memory circuitry. If the dbm card is separated from the mcp card, all of the stored information on the card is lost. The generic feature software and feature authorization information is installed ...

  • Page 270: Group Controller Circuit

    8-10 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 000 the group controller embedded circuit serves as the communication link in the coral ipx office system, between the mcb office and the peripheral cards via the mbp office backplane. The group c...

  • Page 271

    Coral ipx office installation manual common control cards 8-11 mcb office car d ma in contr ol boar d 8 figure 8-3 coral ipx office voice switching - peripheral services - 1024 pcm time slot group controller - call progress tone generators shared service controller rmi-f expansion cabinet interface ...

  • Page 272

    8-12 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 figure 8-4 highways for ipx office with ipx expansion units a2 b2 a1 b1 a5 b5 a7 b7 a0 b0 a3 b3 a4 b4 igc peripheral service & group controller 1024 time slots 384 time slots 1st ipx office expans...

  • Page 273

    Coral ipx office installation manual common control cards 8-13 mcb office car d ma in contr ol boar d 8 figure 8-5 highways for ipx office with ipx 500x/800x cages a2 b2 a1 b1 a5 b5 a7 b7 a0 b0 a3 b3 a4 b4 igc peripheral service & group controller 1024 time slots 384 time slots main unit 128 time sl...

  • Page 274

    8-14 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 figure 8-6 highways for ipx office with flexicom 200 cslx cabinets a1 b1 a5 b5 a7 b7 a0 b0 igc peripheral service & group controller 1024 time slots main unit 128 time slots 128 time slots 128 tim...

  • Page 275

    Coral ipx office installation manual common control cards 8-15 mcb office car d ma in contr ol boar d 8 circuit description clock selection the external clock synchronization selector monitors the two inputs for the presence of an 8.0 khz clock signal, which may be derived from a digital trunk card....

  • Page 276

    8-16 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 0 the mcb office card supervises the feature authorization using the sau (software authorization unit) lock device. The sau is a small, encapsulated device that is plugged into a connector on the ...

  • Page 277

    Coral ipx office installation manual common control cards 8-17 mcb office car d ma in contr ol boar d 8 figure 8-7 software authorization unit (sau) detail when starting up the coral system, ensure that there are no sau fault messages during startup or sau alarms (pi branch: root, 1, 1, 15-controls)...

  • Page 278: Front Panel Features

    8-18 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 0 the front panel of the mcb office card contains various elements that are accessed via the front panel. These elements, include led indicators, buttons, connectors, and disk card slots. Because ...

  • Page 279: Imc8 Flash Memory Card

    Coral ipx office installation manual common control cards 8-19 mcb office car d ma in contr ol boar d 8 0 the imc8 flash card is an integrated memory card with an 8 mb flash memory capacity. It contains the generic software of the coral and is used to store the system database. See imc8 flash memory...

  • Page 280: Kb0 Rs-232E Programming Port

    8-20 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 0 the serial interface of the kb0 programming port on the mcb office conforms to the eia rs-232e specification. It is wired as a data terminal equipment (dte) device using a popular 9-pin, male, d...

  • Page 281: Ugw Rs-232E Programming Port

    Coral ipx office installation manual common control cards 8-21 mcb office car d ma in contr ol boar d 8 0 the serial interface of the ugw programming port on the mcb office conforms to the eia rs-232e specification. It is wired as a data terminal equipment (dte) device using a popular 9-pin, male, d...

  • Page 282

    8-22 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 0 the dbm card is an expansion memory card. It adds an additional 4 or 8mb sram to the coral main control. The card is equipped with an extension connector on its top side. However, only one dbm c...

  • Page 283

    Coral ipx office installation manual common control cards 8-23 mcb office car d ma in contr ol boar d 8 0 a new lithium battery can maintain power to the mcb office memory circuitry and real-time clock for approximately 90 days. The battery is not recharged by the system power. Thus, if the battery ...

  • Page 284

    8-24 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 figure 8-10 mcb office card battery insulator release kb0 release button p5 p4 ps office connector p10 p14 mbp offic connector j10 / j13* j11 backup battery compact flash card (optional) backup ba...

  • Page 285: Specifications - McB Office

    Coral ipx office installation manual common control cards 8-25 mcb office car d ma in contr ol boar d 8 00 microprocessor:........................Intel™ 80386ex cpu clock rate:......................32 mhz memory addressing: ...............16 mb data bus structure:.................16 bit; shared with...

  • Page 286: Notes:

    8-26 common control cards coral ipx office installation manual mcb office car d ma in contr ol boar d 8 notes:.

  • Page 287: 8.3

    Coral ipx office installation manual common control cards 8-27 led car d 8 8.3 led card 0 the led card includes the eight (8) diagnostic led indicators that appear on the front panel of the ipx office system. These leds are: power (green) - indicates whether the 5v power output is functional gc act....

  • Page 288

    8-28 common control cards coral ipx office installation manual led car d 8 0 this section describes how to remove the led office card from the unit cover and replace it with a new one. To replace the led office card: 1. Open the unit cover. See opening the unit cover, page 6-9 . 2. Unfasten the thre...

  • Page 289: 8.4

    Coral ipx office installation manual common control cards 8-29 mrc ca rd 8 8.4 mrc card 0 functional description the mrc module is a daughter card installed on top of the mcb office card. The mrc module provides media channels used to convert digital media streams into ip packets and vice versa, the...

  • Page 290

    8-30 common control cards coral ipx office installation manual mrc ca rd 8 the voip capacity of the coral ipx office main unit is 240 ip endpoints, which is a combination of ip terminals, ip trunks, and mrc media channels. Mrc media channels are needed when an ip endpoint (sip or mgcp) is connected ...

  • Page 291

    Coral ipx office installation manual common control cards 8-31 mrc ca rd 8 mrc layout the mrc card includes two connectors, p1 and p2, that connect to connectors j4 and j7, respectively. The card is initialized via the mcb office, there is no mac number label on the card, and the mac number is not u...

  • Page 292: Installing The Mrc

    8-32 common control cards coral ipx office installation manual mrc ca rd 8 0 the parts used to attach the mrc card to the mcb office are listed below. See table 8-4 . The mrc card is secured to the mcb office by a threaded spacer that is already installed onto the mcb office card by the manufacturer...

  • Page 293

    Coral ipx office installation manual common control cards 8-33 mrc ca rd 8 installing the mrc card 1. If necessary, remove the ntu office card. See installing and replacing the ntu office card, page 11-9 . 2. Position the mrc card on top of the mcb office card and align the four fastening holes on t...

  • Page 294: Removing The Mrc

    8-34 common control cards coral ipx office installation manual mrc ca rd 8 0 1. Repeat preparing for installation, page 8-45 . 2. Remove the m3x6 phillips screws and washers that secure the mrc card to the standoff spacers of the mcb office card and safeguard for future re-assembly. 3. Place your th...

  • Page 295: 8.5

    Coral ipx office installation manual common control cards 8-35 im c8 fla sh memory car d 8 8.5 imc8 flash memory card 0 the imc8 flash memory card is a removable component of the coral ipx office common control section. It is installed on the mcb office. The imc8 card incorporates 8 mb of erasable, ...

  • Page 296: Removing The Imc8

    8-36 common control cards coral ipx office installation manual im c8 fla sh memory car d 8 0 the flash card contains three types of data: generic feature software version database backup boot code when replacing a flash card with another card that contains upgraded software, the new card might not c...

  • Page 297

    Coral ipx office installation manual common control cards 8-37 im c8 fla sh memory car d 8 4 if expansion cages are installed in the system, turn the power supply of all expansion cages off. 5 if the main power supply is turned off, press the flash memory card release button on the front panel of th...

  • Page 298: Inserting The Imc8

    8-38 common control cards coral ipx office installation manual im c8 fla sh memory car d 8 2 the flash memory card does not occupy a card slot within the coral system. It is inserted into the flash drive of the mcb office card. The flash memory release button releases the flash card. An arrow on the...

  • Page 299

    Coral ipx office installation manual common control cards 8-39 im c8 fla sh memory car d 8 ccs is on the air...... (root) ccs xx.Xx.Xx copyright (c) 1991-xxxx............... Name - (site name) sau# - after the second message appears, the system is initialized properly and capable of processing calls...

  • Page 300: Specifications

    8-40 common control cards coral ipx office installation manual im c8 fla sh memory car d 8 2 storage capacity:........................................8,388,608 bytes (8mb) memory configuration: ..............................16 bits pcmcia:....................................................Standard ...

  • Page 301: 8.6

    Coral ipx office installation manual common control cards 8-41 compact flash disk 8 8.6 compact flash disk 2 an ata-type pcmcia connector houses the compact flash disk (cfd) memory. The cfd disk has an erasable memory capacity of 64mb or more. The cfd is used to back up applications for which there ...

  • Page 302: Notes:

    8-42 common control cards coral ipx office installation manual compact flash disk 8 notes:.

  • Page 303: 8.7

    Coral ipx office installation manual common control cards 8-43 dbm car d 8 8.7 dbm card 2 the dbm memory expansion card is a component of the coral ipx office common control section. The dbm integrates 4mb or 8 mb of static random access memory (sram), used to store the configuration database of a i...

  • Page 304

    8-44 common control cards coral ipx office installation manual dbm car d 8 when a dbm card is required a dbm card is required when any of the following conditions exist: coral directory, traffic, or call log features are used coralink adapter circuitry is relevant to your system version refer to the...

  • Page 305: Installing The Dbm Card

    Coral ipx office installation manual common control cards 8-45 dbm car d 8 2 the dbm card is secured to the mcb office by a threaded spacer. The parts used to attach the spacer to the mcb office are listed below. The dbm card assembly kit includes additional parts. However, you only need to use the ...

  • Page 306

    8-46 common control cards coral ipx office installation manual dbm car d 8 installing the dbm card 1. Open the ipx office unit. See opening the unit cover, page 6-9 . 2. Fasten the three hex m3x6 standoff spacers into the three holes displayed in figure 8-18 . 3. Position the dbm card on top of the ...

  • Page 307

    Coral ipx office installation manual common control cards 8-47 dbm car d 8 figure 8-18 dbm assembly onto mcb office m3 spacers for dbm-x p1.

  • Page 308: Removing The Dbm Card

    8-48 common control cards coral ipx office installation manual dbm car d 8 2 1. Perform the database binary backup procedure before removing the dbm card from the main control card. 2. Repeat step 1 through step 4 on preparing for installation, page 8-45 . 3. Remove the m3x6 phillips screws and wash...

  • Page 309: Specifications - Dbm Card

    Coral ipx office installation manual common control cards 8-49 dbm car d 8 2 storage capacity per unit: ........................1,048,576 bytes (1.0mb) memory configuration: ............................ 524,288 16 bits memory device:.........................................128kb 8 bit sram operating...

  • Page 310: Notes:

    8-50 common control cards coral ipx office installation manual dbm car d 8 notes:.

  • Page 311: Chapter

    Coral ipx office installation manual chapter 9 shared service cards 9.1 shared service circuitry.............................................................9-1 9.2 mrc-8, 16, 32, 64 modules........................................................9-5 9.3 u-rmi / u-mr / rmi / mr office cards.............

  • Page 313: 9.1

    Coral ipx office installation manual shared service cards 9-1 shar ed servi ce cir cuitry inst al lation 9 9.1 shared service circuitry installation 0 the shared service circuits provide functions such as media gateway (mg) channels, dial and call progress detection, mf tone dialing reception, multi...

  • Page 314

    9-2 shared service cards coral ipx office installation manual shar ed servi ce cir cuitry inst al lation 9 00 shared service circuits in the u-rmi office, u-mr office, rmi office and mr office cards are embedded in the mr/rmi-f (u60) unit and the urc (u73) unit. One of these cards may be installed i...

  • Page 315

    Coral ipx office installation manual shared service cards 9-3 shar ed servi ce cir cuitry inst al lation 9 0 additional shared service cards may be installed in the optional coral ipx 500x and 800x expansion cages. Additional shared service cards include, but are not limited to the following: .........

  • Page 316

    9-4 shared service cards coral ipx office installation manual shar ed servi ce cir cuitry inst al lation 9 these cards are described in the coral service and peripheral cards installation manual. Shared service cards may be installed in any available peripheral card slot in the optional expansion un...

  • Page 317: 9.2

    Coral ipx office installation manual shared service cards 9-5 mrc-8 , 16, 32, 6 4 mo dules (med ia resou rce car d) 9 9.2 mrc-8, 16, 32, 64 modules (media resource card) 0 figure 9-1 illustrates the mrc card circuit layout. Shared service circuits in the mrc cards are embedded in dsp units. The main...

  • Page 318: Layout and Installation

    9-6 shared service cards coral ipx office installation manual mrc-8 , 16, 32, 6 4 mo dules (med ia resou rce car d) 9 0 the mrc card includes two connectors that connect to connectors j4 and j7 on the mcb office. For more information about various aspects of the card, refer to section 8, mrc card on...

  • Page 319: 9.3

    Coral ipx office installation manual shared service cards 9-7 u-rmi / u-mr / rmi / mr office car ds 9 9.3 u-rmi / u-mr / rmi / mr office cards 0 figure 9-3 through figure 9-6 , starting on page 9-11 , display the u-rmi office, u-mr office, rmi office and mr office card circuit layout. The main share...

  • Page 320: Features

    9-8 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 0. Table 9-4 u-rmi / u-mr office / rmi / mr office features separate authorization is required to allocate the dtmf, clid, 3way and conf circuits supported by the u-rmi office and u-mr office cards....

  • Page 321

    Coral ipx office installation manual shared service cards 9-9 u-rmi / u-mr / rmi / mr office car ds 9 figure 9-2 u-rmi / u-mr / rmi mr office architecture dtmf receivers (dtr) 1 2 3 4 5 6 7 8 9 * 0 # call progress tone detectors (dtd) fourteen-party meet-me conferences caller id circuits (idsp) thre...

  • Page 322

    9-10 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 the u-rmi office, u-mr office, rmi office and mr office cards include: configuration jumpers, as described on page 9-15 external connectors, as described on page 9-17 mr/rmi-f software, as describe...

  • Page 323

    Coral ipx office installation manual shared service cards 9-11 u-rmi / u-mr / rmi / mr office car ds 9 figure 9-3 u-rmi office card circuits layout, front panel and jumpers urc u-rmi office m2/p m1 u73 u60 modem rmi-f software urc software p rmi-f relay contacts 1-2 relay contacts 3-4 p4 p6 p5 p3 p2...

  • Page 324

    9-12 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 figure 9-4 rmi office card circuits layout, front panel and jumpers rmi office m2/p m1 u60 modem rmi-f software p rmi-f p4 p6 p5 p3 p2 1 2 3 m1 (internal music) m1 (external music) m1 p2 1 2 3 m2 (...

  • Page 325

    Coral ipx office installation manual shared service cards 9-13 u-rmi / u-mr / rmi / mr office car ds 9 figure 9-5 u-mr office card circuits layout, front panel and jumpers urc u-mr office m2/p m1 u73 u60 mr software urc software p mr p4 p3 p2 1 2 3 m1 (internal music) m1 (external music) m1 p2 1 2 3...

  • Page 326

    9-14 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 figure 9-6 mr office card circuits layout, front panel and jumpers mr office m2/p m1 u60 mr software p mr p4 p3 p2 1 2 3 m1 (internal music) m1 (external music) m1 p2 1 2 3 m2 (external music) p (p...

  • Page 327: Configuration Jumpers

    Coral ipx office installation manual shared service cards 9-15 u-rmi / u-mr / rmi / mr office car ds 9 0 the u-rmi office, rmi office, u-mr office and mr office cards are equipped with jumpers (p2 - p6) that enable or disable various functions. The enabling or disabling is accomplished by jumper str...

  • Page 328: Indicators

    9-16 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 0 the u-rmi office, rmi office, u-mr office and mr office cards are equipped with two leds, located on the card front panel (see figure 9-3 on page 9-11 through figure 9-6 on page 9-14 ). Table 9-6...

  • Page 329: External Connectors

    Coral ipx office installation manual shared service cards 9-17 u-rmi / u-mr / rmi / mr office car ds 9 the card front panel connectors, figure 9-8 , provides music connection, paging connection, and relay circuits. The music and paging connectors are stereo 3.5 mm phone plugs, see figure 9-9 . Table...

  • Page 330: Mr/rmi-F Eprom (U60)

    9-18 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 0 figure 9-3 on page 9-11 through figure 9-6 on page 9-14 illustrate the mr/rmi-f eprom (u60) location on the u-rmi office, u-mr office, rmi office and mr office cards. The mr/rmi-f is displayed in...

  • Page 331

    Coral ipx office installation manual shared service cards 9-19 u-rmi / u-mr / rmi / mr office car ds 9 mr and rmi-f database programming the mr and rmi-f provides the features listed in table 9-8. The mr and rmi-f in a coral system has considerable impact on the system database. Use the pi to verify...

  • Page 332

    9-20 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 table 9-8 mr and rmi-f features table 9-9 mr and rmi-f pi (route: plis) circuit purpose circuit no. Default name default dial no. Na na 0-22 — — page (rly1) external voice page (public address) 23 ...

  • Page 333: Urc Prom (U73)

    Coral ipx office installation manual shared service cards 9-21 u-rmi / u-mr / rmi / mr office car ds 9 0 figure 9-3 on page 9-11 and figure 9-5 on page 9-13 display the urc prom (u73) location on the u-rmi office and u-mr office cards. The urc (universal resource card) unit software is provided with...

  • Page 334

    9-22 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 urc2 database programming (u-rmi office and u-mr office cards) the urc provides the features listed in table 9-10. The urc in a coral system has considerable impact on the system database. Use the ...

  • Page 335

    Coral ipx office installation manual shared service cards 9-23 u-rmi / u-mr / rmi / mr office car ds 9 feature authorization (route: feat,1) urc dtmf urc clid urc 3way urc conf separate software authorization is required to allocate the urc resources. Refer to program interface (pi) and database ref...

  • Page 336

    9-24 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 card list (route: clis) card type must show urc2 in the p_type field of shelf #1, slot #7. The card status can be one of the following: active inactive the port list supplies detailed information o...

  • Page 337

    Coral ipx office installation manual shared service cards 9-25 u-rmi / u-mr / rmi / mr office car ds 9 table 9-13 urc dtr/dtmf pi configuration urc configuration pi route: dtb,11 pi route: plis dtmf urc2 0-24 urc4 0-48 total resource points needed shelf/slot/ckt type dial no. Name short : full 1 1 1...

  • Page 338

    9-26 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 27 27 1 7 26 dtr /dtmf — — — 28 28 1 7 27 dtr /dtmf — — — 29 29 1 7 28 dtr /dtmf — — — 30 30 1 7 29 dtr /dtmf — — — 31 31 1 7 30 dtr /dtmf — — — 32 32 1 7 31 dtr /dtmf — — — 33 33 1 7 32 dtr /dtmf ...

  • Page 339

    Coral ipx office installation manual shared service cards 9-27 u-rmi / u-mr / rmi / mr office car ds 9 table 9-14 urc dtb pi route table 9-15 urc spare ports (not used) urc configuration pi route: dtb,11 pi route: plis meet-me (0-6) total resource points needed shelf/slot/ckt type dial no. Name shor...

  • Page 340

    9-28 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 table 9-16 urc three-way conference (c3way) pi configuration urc configuration pi route: dtb,11 pi route: plis c3way (0-24) total resource points needed shelf/slot/ckt type dial no. Name short : fu...

  • Page 341

    Coral ipx office installation manual shared service cards 9-29 u-rmi / u-mr / rmi / mr office car ds 9 table 9-17 urc idsp cid (caller id) transmitters pi configuration urc configuration pi route: dtb,11 pi route: plis cid (0-32) total resource points needed shelf/slot/ckt type dial no. Name short :...

  • Page 342

    9-30 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 26 26 1 7 105 idsp — — — 27 27 1 7 106 idsp — — — 28 28 1 7 107 idsp — — — 29 29 1 7 108 idsp — — — 30 30 1 7 109 idsp — — — 31 31 1 7 110 idsp — — — 32 32 1 7 111 idsp — — — * the ports listed abo...

  • Page 343

    Coral ipx office installation manual shared service cards 9-31 u-rmi / u-mr / rmi / mr office car ds 9 table 9-18 urc dial tone detector (dtd) pi configuration urc configuration pi route: dtb,11 pi route: plis dtd (0-32) total resource points needed shelf/slot/ckt type dial no. Name short : full 1 1...

  • Page 344

    9-32 shared service cards coral ipx office installation manual u-rmi / u-mr / rmi / mr office car ds 9 27 27 1 7 138 dtd — — — 28 28 1 7 139 dtd — — — 29 29 1 7 140 dtd — — — 30 30 1 7 141 dtd — — — 31 31 1 7 142 dtd — — — 32 32 1 7 143 dtd — — — * the ports listed above the double line indicate the...

  • Page 345: 9.4

    Coral ipx office installation manual shared service cards 9-33 thr ee-w ay confer ence (3-w ay) confer ence cir cuitry 9 9.4 three-way conference (3-way) conference circuitry 0 the u-rmi office and u-mr office cards provide eight (max: 24*) independent 3-way (conferences/consultation/broker service)...

  • Page 346: Database Programming

    9-34 shared service cards coral ipx office installation manual thr ee-w ay confer ence (3-w ay) confer ence cir cuitry 9 00 the 3-way circuit requires some database settings. Consult the program interface (pi) and database reference manual for instructions on the database programming required for c3...

  • Page 347: Additional 3-Way Circuits

    Coral ipx office installation manual shared service cards 9-35 thr ee-w ay confer ence (3-w ay) confer ence cir cuitry 9 0 additional digital conference bridge cards may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the “coral ...

  • Page 348

    9-36 shared service cards coral ipx office installation manual thr ee-w ay confer ence (3-w ay) confer ence cir cuitry 9 00 number of circuits: u-rmi office card 24 max. 8 default u-mr office card 24 max. 8 default rmi office card 0 mr office card 0 8drcf card 6 (requires ipx 800x expansion cage) cn...

  • Page 349: 9.5

    Coral ipx office installation manual shared service cards 9-37 multi-party confer ence (conf) meet me confer ence cir cuitry 9 9.5 multi-party conference (conf) meet me conference circuitry 0 the u-rmi office and u-mr office cards provide two (max: 6*) meet-me bridge conference circuits for 14 parti...

  • Page 350: Feature Descriptions

    9-38 shared service cards coral ipx office installation manual multi-party confer ence (conf) meet me confer ence cir cuitry 9 0 the meet me bridge conference circuit (conf) in the coral ipx office system enables: group call multiparty conference urc chained meet me groups the urc has 6 circuits tha...

  • Page 351: Database Programming

    Coral ipx office installation manual shared service cards 9-39 multi-party confer ence (conf) meet me confer ence cir cuitry 9 0 the meet me bridge conference circuit (conf) requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for ins...

  • Page 352

    9-40 shared service cards coral ipx office installation manual multi-party confer ence (conf) meet me confer ence cir cuitry 9 gains table (route: root,0,1,3) entry #12 of the gains table can be used to set gain parameters to the conference. For more information see chapter 19 in the program interfa...

  • Page 353

    Coral ipx office installation manual shared service cards 9-41 multi-party confer ence (conf) meet me confer ence cir cuitry 9 conference lock -field 9, index 190. Conference dial numbers - field 30 (shelf #1, slot #7, ckt #48-53). Urc configuration (route: cdb,11,1) meet me - defines the maximum nu...

  • Page 354

    9-42 shared service cards coral ipx office installation manual multi-party confer ence (conf) meet me confer ence cir cuitry 9 additional digital conference bridge cards may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the “co...

  • Page 355

    Coral ipx office installation manual shared service cards 9-43 multi-party confer ence (conf) meet me confer ence cir cuitry 9 00 number of circuits: u-rmi office card............... 6 max. 2 default u-mr office card ................ 6 max. 2 default rmi office card................... 0 mr office ca...

  • Page 356: Notes:

    9-44 shared service cards coral ipx office installation manual multi-party confer ence (conf) meet me confer ence cir cuitry 9 notes:.

  • Page 357: 9.6

    Coral ipx office installation manual shared service cards 9-45 dtmf receiver (dtr) 9 9.6 dtmf receiver (dtr) 0 the u-rmi office and u-mr office cards provide 24 (max: 24*) port dtmf receivers and decoders for touch-tone digits. Separate authorization is required to allocate the dtmf circuits support...

  • Page 358: Additional Dtr Circuits

    9-46 shared service cards coral ipx office installation manual dtmf receiver (dtr) 9 0 to provide adequate dtmf dialing quality of service in the system the number of dtmf receivers should match the anticipated traffic volume. The following table provides the number of dtr ports required for several...

  • Page 359: Database Programming

    Coral ipx office installation manual shared service cards 9-47 dtmf receiver (dtr) 9 0 the dtr requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for instructions on the database programming required for the dtr. The following param...

  • Page 360: Tip:

    9-48 shared service cards coral ipx office installation manual dtmf receiver (dtr) 9 0 number of circuits: u-rmi office card..................24 max. 24 default u-mr office card ...................24 max. 24 default rmi office card ......................0 mr office card .......................0 8dtr...

  • Page 361: 9.7

    Coral ipx office installation manual shared service cards 9-49 dial t on e detector (dtd) 9 9.7 dial tone detector (dtd) 0 the u-rmi office and u-mr office cards provide 16 (max: 32*) port dtd (dial tone detector) circuits for enhanced dialing, such as busy outside number auto-redial. (max: *) the m...

  • Page 362: Database Programming

    9-50 shared service cards coral ipx office installation manual dial t on e detector (dtd) 9 0 the dtd requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for instructions on the database programming required. The following parameters...

  • Page 363: Additional Dtd Circuits

    Coral ipx office installation manual shared service cards 9-51 dial t on e detector (dtd) 9 0 additional dtd resources cards may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the coral service and peripheral cards installation ...

  • Page 364: Specifications - Dtd

    9-52 shared service cards coral ipx office installation manual dial t on e detector (dtd) 9 0 number of circuits: u-rmi office card..................32 max. 16 default u-mr office card ...................32 max. 16 default rmi office card ......................0 mr office card .........................

  • Page 365: 9.8

    Coral ipx office installation manual shared service cards 9-53 call er id for sl t (idsp) 9 9.8 caller id for slt (idsp) 0 the u-rmi office and u-mr office cards provide 16 (max: 32*) idsp ports. Separate authorization is required to allocate the idsp circuits supported by the u-rmi office and u-mr ...

  • Page 366: Database Programming

    9-54 shared service cards coral ipx office installation manual call er id for sl t (idsp) 9 0 the cid requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for instructions on the database programming required. The following parameters...

  • Page 367: Additional Cid Circuits

    Coral ipx office installation manual shared service cards 9-55 call er id for sl t (idsp) 9 additional cid resources cards may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the coral service and peripheral cards installation ma...

  • Page 368: Specifications - Cid

    9-56 shared service cards coral ipx office installation manual call er id for sl t (idsp) 9 0. Number of circuits: u-rmi office card..................32 max. 16 default u-mr office card ...................32 max. 16 default rmi office card ......................0 mr office card ........................

  • Page 369: 9.9

    Coral ipx office installation manual shared service cards 9-57 mfc receiver (mfr) multi-fr equency code receiver cir cuit 9 9.9 mfc receiver (mfr) multi-frequency code receiver circuit 0 the u-rmi office, u-mr office, rmi office and mr office cards do not provide circuits for mfc (multi-frequency co...

  • Page 370: Specifications

    9-58 shared service cards coral ipx office installation manual mfc receiver (mfr) multi-fr equency code receiver cir cuit 9 0 number of circuits: u-rmi office card..................0 u-mr office card ...................0 rmi office card ......................0 mr office card .......................0...

  • Page 371: 9.10

    Coral ipx office installation manual shared service cards 9-59 vo ip media gateway ( m g) 9 9.10 voip media gateway (mg) 0 media channels are provided by an mrc module, which is a daughterboard attached to the mcb office card in piggyback fashion. The mrc modules provide the following media channels...

  • Page 372: Notes:

    9-60 shared service cards coral ipx office installation manual vo ip media gateway ( m g) 9 notes:.

  • Page 373: 9.11

    Coral ipx office installation manual shared service cards 9-61 remote maintenance (modem ) 9 9.11 remote maintenance (modem) 0 the u-rmi office and rmi office cards provide an auto-answer data modem. A full duplex, asynchronous, ascii modem, used for remote programming of the system database, diagno...

  • Page 374

    9-62 shared service cards coral ipx office installation manual remote maintenance (modem ) 9 figure 9-11 modem - jumper configuration function rx modem - on rx modem - off p6 p5 p2 2 1 3 2 1 3 function tx modem - on tx modem - off p5 2 1 3 2 1 3 p6 p3 p4 the modem may only be used to communicate wit...

  • Page 375: Database Programming

    Coral ipx office installation manual shared service cards 9-63 remote maintenance (modem ) 9 0 this function requires installation of additional jumpers (p5 and p6, pins 1 and 2 must be connected) on the u-rmi office and rmi office cards. Described on page 9-61 . The modem requires the appropriate d...

  • Page 376

    9-64 shared service cards coral ipx office installation manual remote maintenance (modem ) 9 5. Terminal setup (route: term,0) use this field to set up the communication parameters for the data applications. Refer to chapter 17 in the program interface (pi) and database reference manual for more det...

  • Page 377

    Coral ipx office installation manual shared service cards 9-65 remote maintenance (modem ) 9 additional modem ports may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the coral service and peripheral cards installation manual. S...

  • Page 378: Specifications - Modem

    9-66 shared service cards coral ipx office installation manual remote maintenance (modem ) 9 0 number of circuits: u-rmi office card..................1 rmi office card ......................1 u-mr office card ...................0 mr office card .......................0 8drcf card ......................

  • Page 379: 9.12

    Coral ipx office installation manual shared service cards 9-67 data s erial ports (rs -232 e) kb0 , kb1, kb2, kb3 9 9.12 data serial ports (rs-232e) kb0, kb1, kb2, kb3 0 the u-rmi office, u-mr office, rmi office and mr office cards do not provide serial ports. The coral ipx provides one eia rs-232e ...

  • Page 380

    9-68 shared service cards coral ipx office installation manual data s erial ports (rs -232 e) kb0 , kb1, kb2, kb3 9 0 rs-232e serial ports may be installed in the optional coral ipx 800x expansion cage. The additional cards include: this card is described in the coral service and peripheral cards in...

  • Page 381: Specifications - Rs-232E

    Coral ipx office installation manual shared service cards 9-69 data s erial ports (rs -232 e) kb0 , kb1, kb2, kb3 9 0 number of circuits: u-rmi office card..................0 u-mr office card ...................0 rmi office card......................0 mr office card .......................0 8drcf ca...

  • Page 382: Notes:

    9-70 shared service cards coral ipx office installation manual data s erial ports (rs -232 e) kb0 , kb1, kb2, kb3 9 notes:.

  • Page 383: 9.13

    Coral ipx office installation manual shared service cards 9-71 music ba ckgr ound and music- on -hold (m1/m2) 9 9.13 music background and music-on-hold (m1/m2) 0 the u-rmi office, u-mr office, rmi office and mr office cards provide the following common system functions: two music inputs, one of whic...

  • Page 384

    9-72 shared service cards coral ipx office installation manual music ba ckgr ound and music- on -hold (m1/m2) 9 0. The system music source m1 may be either from an internal or an external source. Figure 9-13 displays the jumper settings for the source type. Table 9-20 music-1 internal/external selec...

  • Page 385

    Coral ipx office installation manual shared service cards 9-73 music ba ckgr ound and music- on -hold (m1/m2) 9 0. The system music source m2/p may be either external music source or a voice page output. Figure 9-14 displays the jumper settings for the music source. Table 9-21 music-2 m2/p music/pag...

  • Page 386: Database Programming

    9-74 shared service cards coral ipx office installation manual music ba ckgr ound and music- on -hold (m1/m2) 9 0 each u-rmi office, u-mr office, rmi office or mr office card provides two music sources; m1 (external/ internal selectable) and m2 (external) . The music feature requires the appropriate...

  • Page 387

    Coral ipx office installation manual shared service cards 9-75 music ba ckgr ound and music- on -hold (m1/m2) 9 use the retain_hunt_music_source field as described in chapter 9, in the program interface (pi) and database reference manual. 7. Gains table (route: root,0,1,3) entry #11 of the gains tab...

  • Page 388: External Connections

    9-76 shared service cards coral ipx office installation manual music ba ckgr ound and music- on -hold (m1/m2) 9 0 figure 9-16 illustrates the connection of customer-supplied music sources. The first music source is passed to any port in a hold state and may also be selected as background music over ...

  • Page 389

    Coral ipx office installation manual shared service cards 9-77 music ba ckgr ound and music- on -hold (m1/m2) 9 0 additional music ports may be installed in the optional coral ipx 800x expansion cage. The additional cards include: these cards are described in the coral service and peripheral cards i...

  • Page 390: Specifications - Music

    9-78 shared service cards coral ipx office installation manual music ba ckgr ound and music- on -hold (m1/m2) 9 0 number of circuits: u-rmi office card..................2 (1 when paging is used) u-mr office card ...................2 (1 when paging is used) rmi office card ......................2 (1 ...

  • Page 391: 9.14

    Coral ipx office installation manual shared service cards 9-79 vo ice paging (public addr ess) a nd relay-1 public addr ess 9 9.14 voice paging (public address) and relay-1 public address 0 the u-rmi office, u-mr office, rmi office and mr office cards provide one external paging interface (public ad...

  • Page 392

    9-80 shared service cards coral ipx office installation manual vo ice paging (public addr ess) a nd relay-1 public addr ess 9 relay contacts 1-2 paging/relay relay contacts 1-2 can be dial-activated or used as a system alarm. The selection between the paging or system alarm/dial-operated is accompli...

  • Page 393

    Coral ipx office installation manual shared service cards 9-81 vo ice paging (public addr ess) a nd relay-1 public addr ess 9 0. The system paging output m2/p may be either music source or a voice page output. Figure 9-19 displays the jumper settings for the music source. Table 9-22 paging m2/p musi...

  • Page 394: Database Programming

    9-82 shared service cards coral ipx office installation manual vo ice paging (public addr ess) a nd relay-1 public addr ess 9 0. The relay contacts 1-2 may be either rly1 (page) or rly3 (system alarm or dial-operated) contacts. Figure 9-21 displays the jumper settings for the page feature. Table 9-2...

  • Page 395

    Coral ipx office installation manual shared service cards 9-83 vo ice paging (public addr ess) a nd relay-1 public addr ess 9 each u-rmi office, u-mr office, rmi office or mr office card provides one paging output: the external voice paging port operates by using both the relay circuit (rly1) and th...

  • Page 396: External Connections

    9-84 shared service cards coral ipx office installation manual vo ice paging (public addr ess) a nd relay-1 public addr ess 9 0 each u-rmi office, u-mr office, rmi office or mr office card provides a voice page interface for external paging and public address. The interface supplies a line-level (-1...

  • Page 397: Relay Electrical Limitations

    Coral ipx office installation manual shared service cards 9-85 vo ice paging (public addr ess) a nd relay-1 public addr ess 9 the relay contact closes continuously during access to the voice page interface. Although not always required, the relay contact is often utilized for "mac precedence" or "mu...

  • Page 398: Specifications - Paging

    9-86 shared service cards coral ipx office installation manual vo ice paging (public addr ess) a nd relay-1 public addr ess 9 0 number of circuits: u-rmi office card..................1 (0 when music-2 is used) u-mr office card ...................1 (0 when music-2 is used) rmi office card ..............

  • Page 399: 9.15

    Coral ipx office installation manual shared service cards 9-87 una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 9.15 una/bell and relay-2 (universal night answering/central bell) 0 the u-rmi office, u-mr office, rmi office and mr office cards provide relay contacts for central ring...

  • Page 400

    9-88 shared service cards coral ipx office installation manual una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 0. The relay contacts 3-4 may be either rly2 (bell) or rly3 (system alarm or dial-operated) contacts. Figure 9-21 displays the jumper settings for the page feature. Table...

  • Page 401: Database Programming

    Coral ipx office installation manual shared service cards 9-89 una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 0 the central bell (una) requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for instructions on the da...

  • Page 402: External Connections

    9-90 shared service cards coral ipx office installation manual una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 0 incoming trunk calls may be directed to activate a relay contact at certain times of the day (typically after normal business hours). The relay contact sounds a tone ov...

  • Page 403: Relay Electrical Limitations

    Coral ipx office installation manual shared service cards 9-91 una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 0 the relay contacts have specific electrical limitations. For further detail, see relay contacts on page 9-103 . These limitations must not be exceeded. In addition, the...

  • Page 404: Specifications - Bell/una

    9-92 shared service cards coral ipx office installation manual una/bell and rela y-2 (universal nig ht answering/cen tral bell) 9 0 number of circuits: u-rmi office card..................1 (0 when accessory/alarm relay is used) u-mr office card ...................1 (0 when accessory/alarm relay is u...

  • Page 405: 9.16

    Coral ipx office installation manual shared service cards 9-93 accessory or alarm rela y-3 major/mi nor alarm 9 9.16 accessory or alarm relay-3 major/minor alarm 0 the u-rmi office, u-mr office, rmi office and mr office cards provide one relay contact for major/minor alarm or accessory interface. Ea...

  • Page 406: Circuit Description

    9-94 shared service cards coral ipx office installation manual accessory or alarm rela y-3 major/mi nor alarm 9 0 figure 9-29 is a simplified circuit diagram of the relay contacts. The relay provide form a (single pole, single throw and normally open) contacts for activating external circuitry and d...

  • Page 407

    Coral ipx office installation manual shared service cards 9-95 accessory or alarm rela y-3 major/mi nor alarm 9 0. The relay contacts 1-2 may be either rly1 (page) or rly3 (system alarm or dial-operated) contacts. Figure 9-31 displays the jumper settings for the page feature. Table 9-25 relay contac...

  • Page 408

    9-96 shared service cards coral ipx office installation manual accessory or alarm rela y-3 major/mi nor alarm 9 . The relay contacts 3-4 may be either rly2 (bell) or rly3 (system alarm or dial-operated) contacts. Figure 9-33 displays the jumper settings for the page feature. Table 9-26 relay contact...

  • Page 409: Database Programming

    Coral ipx office installation manual shared service cards 9-97 accessory or alarm rela y-3 major/mi nor alarm 9 0 the major and minor alarm or accessory interface feature requires the appropriate definitions in the database. Consult the program interface (pi) and database reference manual for instru...

  • Page 410

    9-98 shared service cards coral ipx office installation manual accessory or alarm rela y-3 major/mi nor alarm 9 major/minor alarm relay 1. System features - diagnostics (route: sfe, 9) minor_rly use this parameter to define the relay dial number as the minor alarm situation destination. Major_rly us...

  • Page 411: External Connections

    Coral ipx office installation manual shared service cards 9-99 accessory or alarm rela y-3 major/mi nor alarm 9 0 table 9-7 on page 9-17 lists the function of each interface connector, as they appear on the card front panel, figure 9-8 on page 9-17 illustrates that connector. Dial operated accessory...

  • Page 412: Relay Electrical Limitations

    9-100 shared service cards coral ipx office installation manual accessory or alarm rela y-3 major/mi nor alarm 9 0 the relay contacts have specific electrical limitations. See relay contacts on page 9-103 . Do not exceed these limitations. In addition, the type of load the relay contact operates can...

  • Page 413: Specifications - Relay

    Coral ipx office installation manual shared service cards 9-101 accessory or alarm rela y-3 major/mi nor alarm 9 00 number of circuits: u-rmi office card..................1 (0 when page and bell/una are used) u-mr office card ...................1 (0 when page and bell/una are used) rmi office card.....

  • Page 414: Notes:

    9-102 shared service cards coral ipx office installation manual accessory or alarm rela y-3 major/mi nor alarm 9 notes:.

  • Page 415: 9.17

    Coral ipx office installation manual shared service cards 9-103 relay contacts rl y1, rl y2, rl y3 9 9.17 relay contacts rly1, rly2, rly3 0 the u-rmi office, u-mr office, rmi office and mr office cards incorporate two relay contacts (1-2 and 3-4) for two of the following three features: external voi...

  • Page 416

    9-104 shared service cards coral ipx office installation manual relay contacts rl y1, rl y2, rl y3 9 “welded” closed or failing completely. Arcing also generates high frequency energy that may be coupled to any one of the data buses of the coral ipx office, causing unreliable or unpredictable system...

  • Page 417

    Coral ipx office installation manual shared service cards 9-105 relay contacts rl y1, rl y2, rl y3 9 0 figure 9-37 is a simplified circuit diagram of the two relay contacts. The relays provide form a (single pole, single throw and normally open) contacts for activating external circuitry and devices...

  • Page 418: Specifications - Relays

    9-106 shared service cards coral ipx office installation manual relay contacts rl y1, rl y2, rl y3 9 0 number of circuits: u-rmi office card..................2 u-mr office card ...................2 rmi office card ......................2 mr office card .......................2 8drcf card ..............

  • Page 419: Chapter

    Coral ipx office installation manual chapter 10 peripheral cards 10.1 peripheral card installation .....................................................10-1 10.2 peripheral card description ....................................................10-5 10.3 digital trunk synchronization .....................

  • Page 421: 10.1

    Coral ipx office installation manual peripheral cards 10-1 peripheral car d installati on 10 10.1 peripheral card installation 0 the coral ipx office system divides peripheral interface functions among several different station and trunk card types. Each card contains 4, 8, 16, 20, or 24 circuits. S...

  • Page 422

    10-2 peripheral cards coral ipx office installation manual peripheral car d installati on 10 0 peripheral card installation and initialization are done through automatic identification by the hardware application called "plug and play" (plug in and start working). All the technician has to do is to ...

  • Page 423: Diagnostic Led Indication

    Coral ipx office installation manual peripheral cards 10-3 peripheral car d installati on 10 0 each plug-in office service and peripheral card is equipped with one or two red diagnostic indication leds on the front side, near the right side of the card 1 . These leds can assume one of three states o...

  • Page 424

    10-4 peripheral cards coral ipx office installation manual peripheral car d installati on 10 new card exceed the maximum number allocated in sizes, the card cannot initialize. This situation can be rectified only through restructuring the memory allocation of the system. Initializing the database an...

  • Page 425: 10.2

    Coral ipx office installation manual peripheral cards 10-5 peripheral car d description xxx office car ds 10 10.2 peripheral card description xxx office cards 0 peripheral interface cards are described in the coral service and peripheral cards installation manual. Table 10-8 lists the peripheral int...

  • Page 426

    10-6 peripheral cards coral ipx office installation manual peripheral car d description xxx office car ds 10 figure 10-1 coral ipx office peripheral card slot location figure 10-2 coral ipx office peripheral card types slots 2 - 3 slots 4 - 5 slots 6 - 7 slots 8 - 9 slots 10 - 11 slot 1 xxx office x...

  • Page 427

    Coral ipx office installation manual peripheral cards 10-7 peripheral car d description xxx office car ds 10 table 10-2 coral ipx office peripheral card type card type card name card slot ii 8/16/24sft office 4sa office 8sa office 16sa * office (8sa+8sax) 24sa* office (8sa+16sax) 4sa+8fx office 4sa+...

  • Page 428

    10-8 peripheral cards coral ipx office installation manual peripheral car d description xxx office car ds 10 table 10-3 coral ipx office peripheral card slot location card slot card name card type 2-3, 4-5 8/16/24sft office 4sa office 8sa office 16sa * office (8sa+8sax) 24sa* office (8sa+16sax) 4sa+...

  • Page 429

    Coral ipx office installation manual peripheral cards 10-9 peripheral car d description xxx office car ds 10 10-11 30t office (30t or 30tm jumper selection) 4tbr office pri-30 office udt office (t1 or pri-23 jumper selection) 2dt office (t1, 30t, pri-30 or pri-23 jumper selection) i-b 4t office 4t-c...

  • Page 430

    10-10 peripheral cards coral ipx office installation manual peripheral car d description xxx office car ds 10 analog/digital stations the coral ipx office main and expansion units can accommodate two large-sized station cards to provide a variety of station capacities. The following large-sized stat...

  • Page 431

    Coral ipx office installation manual peripheral cards 10-11 peripheral car d description xxx office car ds 10 table 10-5 4/8sa office card configurations legend (range of possible configurations): analog stations (pots) digital station ports (flexsets) 0 8 16 24 32 40 48 0 8sft 16sft 24sft 24sft 24s...

  • Page 432

    10-12 peripheral cards coral ipx office installation manual peripheral car d description xxx office car ds 10 table 10-6 4/8s office card configurations legend (range of possible configurations): analog stations (pots) digital station ports (flexsets) 0 8 16 24 32 40 48 0 8sft 16sft 24sft 24sft 24sf...

  • Page 433

    Coral ipx office installation manual peripheral cards 10-13 peripheral car d description xxx office car ds 10 never insert “4/8s office” and “4/8sa office” cards in the same coral ipx unit. Never exceed the number of pots and flexsets stations listed in table 10-5 and table 10-6 . Range of possible ...

  • Page 434

    10-14 peripheral cards coral ipx office installation manual peripheral car d description xxx office car ds 10 analog trunks analog trunks are available on a large size 8 circuit card or a small size 4 circuit card. Caller id detection modules can be mounted as daughter boards on these cards. 4t offi...

  • Page 435: 10.3

    Coral ipx office installation manual peripheral cards 10-15 digital t ru nk synch ron ization 10 10.3 digital trunk synchronization 0 the coral ipx office system is capable of operating in either master clock mode or slave clock mode. The selection between modes is made via the pi software. How the ...

  • Page 436

    10-16 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 0 two slots, located in the coral ipx office main unit, are set to accept the digital trunk cards: slot # 8-9 and slot # 10-11. Each card can be installed into either slot. See figure 10-3 below. Synchro...

  • Page 437

    Coral ipx office installation manual peripheral cards 10-17 digital t ru nk synch ron ization 10 system switch from slave clock mode to master clock mode when a digital trunk card is initialized in the appropriate slot, the jumpers properly set, and the shelf/slot combination has been entered as a p...

  • Page 438

    10-18 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 0 optional synchronization cards in the coral ipx office main unit and ipx expansion unit: pri-30 office, 2dt office (pri), udt office (pri-23) t1 - 2dt office (t1), udt office (t1) e1 - 2dt office (30t)...

  • Page 439

    Coral ipx office installation manual peripheral cards 10-19 digital t ru nk synch ron ization 10 bri lines for synchronization 1) bri lines used for synchronization must be defined in the pi (route: dtdb, 4) sync - yes. See pi manual chapter 26 - isdn for more information. 2) it is not recommended t...

  • Page 440: Synchronization Instructions

    10-20 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 0 1. See the selection of the digital trunk cards available at the coral site, given on choosing the best synchronization source, page 10-18 , to determine which cards will be used as the primary and sec...

  • Page 441

    Coral ipx office installation manual peripheral cards 10-21 digital t ru nk synch ron ization 10 flexicom 200 cslx-1 (first expansion unit, only) prm (shelf#2, slot2), sec (shelf#2, slot#3) for more information, refer to chapter 8 of the program interface reference manual. 7. If bri lines are used f...

  • Page 442

    10-22 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 figure 10-3 digital trunk cards jumper settings for synchronization sec 1 2 3 0 prm sync los rai crc gen sec prm sync slots 2 - 3 slots 4 - 5 slots 6 - 7 slots 8 - 9 slots 10 - 11 slots 2 - 3 slots 4 - 5...

  • Page 443

    Coral ipx office installation manual peripheral cards 10-23 digital t ru nk synch ron ization 10 figure 10-4 esim office card jumper settings for synchronization sec prm sync esim office 5 5 5 5 sec. Sync p5 p6 p3 p4 synchronization leds main unit expansion units p3 p3 p5 p5 p4 p4 p6 p6 p3 p5 p4 p6 ...

  • Page 444

    10-24 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 figure 10-5 esix office card jumper settings for synchronization sec prm esix office synchronization indicators 2 1 2 1 2 1 5 5 5 p4 p3 p2 p1 p r im . S y n c . 2 1 5 enabled s e c. S y n c. Disabled sec...

  • Page 445

    Coral ipx office installation manual peripheral cards 10-25 digital t ru nk synch ron ization 10 0 this section describes the different synchronization configurations available with the coral ipx office. The coral ipx office system can house any combination of primary and secondary synchronization u...

  • Page 446

    10-26 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 figure 10-7 primary and secondary in main figure 10-8 primary and secondary in first expansion s esix office esix office sec prm sync esim office esix office esix office sec prm sync esix card in 2nd exp...

  • Page 447

    Coral ipx office installation manual peripheral cards 10-27 digital t ru nk synch ron ization 10 figure 10-9 primary and secondary in second expansion figure 10-10 primary in main and secondary in first expansion esix office sec prm sync esix office sec prm sync esim office esix office sec prm sync ...

  • Page 448

    10-28 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 figure 10-11 primary in first expansion and secondary in main figure 10-12 primary in main and secondary in second expansion esim card in main unit both leds off esix card in 2nd expansion unit prm led o...

  • Page 449

    Coral ipx office installation manual peripheral cards 10-29 digital t ru nk synch ron ization 10 figure 10-13 primary in second and secondary in main figure 10-14 primary in first and secondary in second sec prm sync esim office esix office sec prm sync esix office esix office sec prm sync esix offi...

  • Page 450

    10-30 peripheral cards coral ipx office installation manual digital t ru nk synch ron ization 10 figure 10-15 primary in second and secondary in first sec prm sync esim office esix office sec prm sync esix office esix office sec prm sync esix office esix card in 2nd expansion unit prm led on sec led...

  • Page 451: 10.4

    Coral ipx office installation manual peripheral cards 10-31 se rvice and peripheral ca rd s 10 10.4 service and peripheral cards this section includes a list of all peripheral cards currently used in the coral ipx office system. The coral service and peripheral cards installation manual provides a f...

  • Page 452

    10-32 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 30t office i-b 8-9, 10-11 even: odd: 30t ----- see figure 10-16 . 30t or 30t/m application card, jumper selection. 30 channel, e1 digital trunk interface card. Provides a 4-wire, digital multiplexed, cept ...

  • Page 453

    Coral ipx office installation manual peripheral cards 10-33 se rvice and peripheral ca rd s 10 4sa+8fx office* ii 2-3, 4-5 even: odd: 4sls 8sft see figure 10-33 . Combination station card, 4sa office and 8fx office cards on 4s office board. 12 ports total. 4s+16fx office* ii 2-3, 4-5 even: odd: 4sls...

  • Page 454

    10-34 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 16sft office ii 2-3, 4-5 even: odd: 16sft ----- see figure 10-24 . 16 port, 2-wire sft (station flexset terminal) interface card. Each of the circuits support coral flexset, gkt, cpa, dkt, dst and apdl. 24...

  • Page 455

    Coral ipx office installation manual peripheral cards 10-35 se rvice and peripheral ca rd s 10 pri-30 office i-b 8-9, 10-11 even: odd: pri30 ----- see figure 10-18 . 30 channel, pri (primary rate interface) digital trunk card. Isdn compatible digital interface, european etsi standard (30b+d) at 2.04...

  • Page 456

    10-36 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 table 10-9 coral ipx office piggyback modules for peripheral cards coral ipx office piggyback modules for peripheral cards item description 4cid office the 4cid office is installed on the 4t office card in...

  • Page 457: Tip:

    Coral ipx office installation manual peripheral cards 10-37 se rvice and peripheral ca rd s 10 tip: for 8/16fx installation instructions, refer to figure 10-42 . Table 10-10 u-rmi office, u-mr office, rmi office and mr office features see chapter 9, shared service circuitry f or more information abo...

  • Page 458

    10-38 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-16 30t office card (30t or 30tm) los rai crc gen sec prm sync 30t office u46 u34 1 1 rj-45 socket (female) external view rj-45 plug (male) clip at rear 8 8 1 rxb 2 rxa 3 gnd(shield) 4 txb 5 txa 6...

  • Page 459

    Coral ipx office installation manual peripheral cards 10-39 se rvice and peripheral ca rd s 10 figure 10-17 4tbr office card sec 1 2 3 0 prm sync synchronization source not this card p4 p6 p5 p7 p4 p6 p5 p7 p4 p6 p5 p7 primary (green) secondary (yellow) 4tbr office 1 1 bri line 0, 1, 2, 3 rj-45 sock...

  • Page 460

    10-40 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-18 pri-30 office card los rai crc gen sec prm sync pri-30 office u46 u34 1 1 rj-45 socket (female) external view rj-45 plug (male) clip at rear 8 8 1 rxb 2 rxa 3 gnd(shield) 4 txb 5 txa 6 7 -48vd...

  • Page 461

    Coral ipx office installation manual peripheral cards 10-41 se rvice and peripheral ca rd s 10 figure 10-19 udt office card (t1 or pri-23) los rai crc gen sec prm sync udt office u46 u34 1 1 rj-45 socket (female) external view rj-45 plug (male) clip at rear 8 8 1 rxb 2 rxa 3 gnd(shield) 4 txb 5 txa ...

  • Page 462

    10-42 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-20 2dt office card (30t, t1, pri-30 or pri-23) los rai crc gen sec prm 2dt office sync 1 rj-45 plug (male) clip at rear 8 1 rj-45 socket (female) external view 8 1 rxb 2 rxa 3 gnd(shield) 4 txb 5...

  • Page 463

    Coral ipx office installation manual peripheral cards 10-43 se rvice and peripheral ca rd s 10 figure 10-21 4t office card figure 5-6 illustrates wiring interconnections between the trunk card, station card, and a single line station set. 4t office 0 1 2 3 p u33 card software eprom 4cid office conne...

  • Page 464

    10-44 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-22 4t-cid office card figure 5-6 illustrates wiring interconnections between the trunk card, station card, and a single line station set. 4t-cid office 0 1 2 3 power fail 1 2 3 1 1 trunk 0, 1, 2,...

  • Page 465

    Coral ipx office installation manual peripheral cards 10-45 se rvice and peripheral ca rd s 10 figure 10-23 8sft office card 8sft office u31 p 7 5 3 1 6 4 2 0 card software eprom pins flexset 1/26 a/b0 2/27 a/b1 3/28 a/b2 4/29 a/b3 5/30 a/b4 6/31 a/b5 7/32 a/b6 8/33 a/b7.

  • Page 466

    10-46 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-24 16sft office card 16sft office u31 p 15 9 7 5 3 1 14 10 11 8 6 4 2 0 13 12 card software eprom pins flexset 1/26 a/b0 2/27 a/b1 3/28 a/b2 4/29 a/b3 5/30 a/b4 6/31 a/b5 7/32 a/b6 8/33 a/b7 9/34...

  • Page 467

    Coral ipx office installation manual peripheral cards 10-47 se rvice and peripheral ca rd s 10 figure 10-25 24sft office card 24sft office u31 p 15 9 17 7 19 5 21 3 23 1 14 10 11 16 8 18 6 20 4 22 2 0 13 12 card software eprom pins flexset 1/26 a/b0 2/27 a/b1 3/28 a/b2 4/29 a/b3 5/30 a/b4 6/31 a/b5 ...

  • Page 468

    10-48 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-26 4s office card 4s office u37 card software eprom 1 1 2 2 3 3 u12 3-way 20hz ju3 ring frequency 25hz 1 2 3 sh s ju1 1 2 3 p3 p5 8/16fx office connector 8/16fx office connector pins slt station ...

  • Page 469

    Coral ipx office installation manual peripheral cards 10-49 se rvice and peripheral ca rd s 10 figure 10-27 4sa office card 4sa office j1 p3 p2 aju13 3 2 1 power circuitry 1 0 2 3 3 2 1 iju13 normal software upgrade card processor card software flash card status indicator external i/o connector main...

  • Page 470

    10-50 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-28 8s office card 8s office u37 card software eprom p4 p3 1 1 2 2 3 3 p5 u12 3-way 20hz ju3 ring frequency 25hz 1 2 3 sh s ju1 1 2 3 8/16fx office connector 12sx and 8/16fx office connector 12sx ...

  • Page 471

    Coral ipx office installation manual peripheral cards 10-51 se rvice and peripheral ca rd s 10 figure 10-29 8sa office card 8sa office j1 p3 p2 aju13 3 2 1 power circuitry 1 0 2 3 3 2 1 iju13 normal software upgrade card processor card software flash card status indicator external i/o connector main...

  • Page 472

    10-52 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-30 20s office card 8s office 1 1 2 2 3 3 sh s ju1 1 2 3 20hz ju3 ring frequency 25hz 20s office = 8s office + 12sx office 1 2 3 12sx office j4 j3 pins slt station 1/26 s0 2/27 s1 3/28 s2 4/29 s3 ...

  • Page 473

    Coral ipx office installation manual peripheral cards 10-53 se rvice and peripheral ca rd s 10 figure 10-31 8sa+8sax and 8sa+16sax j1 p3 p2 u4p1 j1 p3 p2 u4p1 3 2 1 3 2 1 iju13 normal software upgrade 4/8sa office 8/16sax office 1/26 s0 2/27 s1 3/28 s2 4/29 s3 5/30 s4 6/31 s5 7/32 s6 8/33 s7 9/34 s8...

  • Page 474

    10-54 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-32 4s+8fx, 4s+16fx, 8s+8fx and 8s+16fx office card s 1 1 2 2 3 3 sh s ju1 1 2 3 20hz 8sft or 16sft diagnostic led ju3 ring frequency 25hz 1 2 3 4s or 8s diagnostic led 4/8s office 4s8f office = 4...

  • Page 475

    Coral ipx office installation manual peripheral cards 10-55 se rvice and peripheral ca rd s 10 figure 10-33 4sa+8fx, 4sa+16fx, 8sa+8fx and 8sa+16fx office card 8sft or 16sft diagnostic led 4sa or 8sa diagnostic laed 4/8sa office 4sa8f office = 4sa + 8fx office office office office office office offi...

  • Page 476

    10-56 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-34 8t office card figure 5-6 illustrates wiring interconnections between the trunk card, station card, and a single line station set. 0 1 2 3 4 5 6 7 8t office 8cid connector p2 power fail power ...

  • Page 477

    Coral ipx office installation manual peripheral cards 10-57 se rvice and peripheral ca rd s 10 figure 10-35 8t-cid office card figure 5-6 illustrates wiring interconnections between the trunk card, station card, and a single line station set. 0 1 2 3 4 5 6 7 power fail power fail power fail power fa...

  • Page 478

    10-58 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-36 ipc office card ipc office hdd usb1 usb2 reset com 1 video network pwr dsp2 dsp1 busy app applications hard disk fax/pci card location battery + shutdown.

  • Page 479

    Coral ipx office installation manual peripheral cards 10-59 se rvice and peripheral ca rd s 10 figure 10-37 4cid office card 4cid office j1 mounting holes for metal screws and spacers for connecting to 4t office metal spacer 4cid office metal screw 4t office metal screw metal washer metal washer.

  • Page 480

    10-60 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-38 8cid card 8cid j1 mounting holes for metal screws and spacers for connecting to 8t office metal spacer 8cid metal screw 8t office metal screw metal washer metal washer.

  • Page 481: Tip:

    Coral ipx office installation manual peripheral cards 10-61 se rvice and peripheral ca rd s 10 figure 10-39 8fx office card - component side tip: for installation instructions refer to figure 10-42 . U18 j2 j1 0 7 1 6 2 5 3 4 8fx office card software eprom p system diagnostic led.

  • Page 482: Tip:

    10-62 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-40 16fx office card - component side tip: for installation instructions refer to figure 10-42 . U18 j2 j1 12 13 14 15 0 7 11 1 6 10 2 5 9 3 4 8 16fx office card software eprom p system diagnostic...

  • Page 483: Tip:

    Coral ipx office installation manual peripheral cards 10-63 se rvice and peripheral ca rd s 10 figure 10-41 8/16fx office card tip: for installation instructions refer to figure 10-42 . 8/16fx office j2 j1 mounting holes for plastic screws and spacers for connecting to 4/8s office plastic spacer 8/1...

  • Page 484

    10-64 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-42 8/16fx office card - installation u37 card software eprom p4 12scsx connector 8/16fcsx connector 12scsx and 8/16fcsx connector p3 1 2 3 p5 u12 3-way 8/16fx office j2 j1 8s office 8/16fx office...

  • Page 485

    Coral ipx office installation manual peripheral cards 10-65 se rvice and peripheral ca rd s 10 figure 10-43 12sx office card - top side 12sx office j4 j3 mounting holes for plastic screws and spacers for connecting to 8s office plastic spacer 12sx office plastic screw 8s office plastic screw.

  • Page 486

    10-66 peripheral cards coral ipx office installation manual se rvice and peripheral ca rd s 10 figure 10-44 12sx office card - rear side 12sx office j4 j3.

  • Page 487: Chapter

    Coral ipx office installation manual chapter 11 system networking 11.1 ntu office card description ........................................................... 11-3 11.2 installing and replacing the ntu office card................................. 11-9 11.3 assembling and removing the wifi card.........

  • Page 489: 11.1

    Coral ipx office installation manual system networking 11-3 ntu office car d d escription 11 11.1 ntu office card description 00 this section describes the networking functions of the coral ipx office system. For a description on how to install the ntu office card, see installing and replacing the n...

  • Page 490

    11-4 system networking coral ipx office installation manual ntu office car d d escription 11 media stream from the lan and wan to the digital world packets are directed from the wan through a customer-supplied router into one of the lan ports. The packets are directed from the lan into one of the la...

  • Page 491

    Coral ipx office installation manual system networking 11-5 ntu office car d d escription 11 0 the coral ipx office system enables seamless integration between the digital and ip world with or without an ntu office card. With an ntu office card, the coral ipx office can connect to the wan directly f...

  • Page 492

    11-6 system networking coral ipx office installation manual ntu office car d d escription 11 figure 11-2 system operation with an ntu office card lan embedded ugw embedded gc mrc ugw switch embedded router wi-fi lan usb wan ntu office rtp packets pcm media mcb office printer wan time switch gc proce...

  • Page 493: Ntu Office Card Components

    Coral ipx office installation manual system networking 11-7 ntu office car d d escription 11 0 the ntu office card is mounted onto the mcb office card and includes the following components (see figure 11-3 ): ntu office card housing. This is the metallic frame that supports the ntu office card. The ...

  • Page 494: Notes:

    11-8 system networking coral ipx office installation manual ntu office car d d escription 11 notes:.

  • Page 495: 11.2

    Coral ipx office installation manual system networking 11-9 in stalling an d replacing th e ntu office car d 11 11.2 installing and replacing the ntu office card 0 the ntu office card installation process includes hardware and software installation. The hardware installation process is described in ...

  • Page 496

    11-10 system networking coral ipx office installation manual in stalling an d replacing th e ntu office car d 11 0 this section describes how to install the ntu office card assembly (including the card housing). See figure 11-5 . 1. If necessary, unplug the power cord that supplies the coral ipx off...

  • Page 497

    Coral ipx office installation manual system networking 11-11 in stalling an d replacing th e ntu office car d 11 figure 11-4 ntu office card fasteners figure 11-5 ntu office card assembly r e m o v e b e f o r e u s e three m3 screws for fastening ntu office card front panel of unit r e m o v e b e ...

  • Page 498

    11-12 system networking coral ipx office installation manual in stalling an d replacing th e ntu office car d 11 0 this section describes how to replace the ntu office card (without replacing the card housing). 1. Unplug the power cord that supplies the coral ipx office system. 2. Remove the unit co...

  • Page 499: 11.3

    Coral ipx office installation manual system networking 11-13 assembling a nd removing th e w ifi car d 11 11.3 assembling and removing the wifi card this section describes how to assemble the wifi card onto the ntu office card. This section describes the assembly and removal of the same wifi and ntu...

  • Page 500

    11-14 system networking coral ipx office installation manual assembling a nd removing th e w ifi car d 11 b. Carefully, press down on the wifi connector until it is firmly attached to the wifi card. C. Repeat step a and step b for the second wifi cable. Figure 11-6 wifi antenna cable installation th...

  • Page 501

    Coral ipx office installation manual system networking 11-15 assembling a nd removing th e w ifi car d 11 wifi card assembly 1. Open the wifi card flap and align the wifi card connector with its corresponding connector on the ntu office card such that there is an angle between the two cards. 2. Push...

  • Page 502: Removing The Wifi Card

    11-16 system networking coral ipx office installation manual assembling a nd removing th e w ifi car d 11 0 1. Remove the wifi antennas. 2. Unplug the power cord that supplies the coral ipx office system. 3. Remove the unit cover. See opening the unit cover, page 6-9 . 4. Carefully disconnect the wi...

  • Page 503

    Coral ipx office installation manual system networking 11-17 assembling a nd removing th e w ifi car d 11 figure 11-8 wifi card removal 2 grip sides of card holder and gently pull outwards card springs upwards 1 open flap and disconnect cables from wifi card 3 pull to remove card.

  • Page 504: Assembling The Wifi Antennas

    11-18 system networking coral ipx office installation manual assembling a nd removing th e w ifi car d 11 0 1. Close the coral ipx office unit cover. Closing the unit cover, page 6-10 . 2. Assemble the wifi antennas as shown in figure 11-9 . Figure 11-9 wifi antenna assembly 00 remove the antennas a...

  • Page 505

    Coral ipx office installation manual system networking 11-19 assembling a nd removing th e w ifi car d 11 0 configure the networking software as described in the documentation provided by the ntu office card software vendor at http://www.Draytek.Com . The ntu office card is named vigor 2900 by the v...

  • Page 506: Specifications

    11-20 system networking coral ipx office installation manual assembling a nd removing th e w ifi car d 11 0 ntu office card hardware interface lan ........................................Port 10/100 base-tx switch wan .......................................1-port 10/100 base-tx port with a rj-45 con...

  • Page 507

    Coral ipx office installation manual system networking 11-21 assembling a nd removing th e w ifi car d 11 network features dhcp server / relay / client dns cache and proxy dynamic dns sntp client call scheduling radius client upnp routing protocol .....................Static routing / rip v2 qos cla...

  • Page 508

    11-22 system networking coral ipx office installation manual assembling a nd removing th e w ifi car d 11 wifi card (wlan access point) protocol.......................................................Ieee802.11b/g compliant wireless client list security ..................................................

  • Page 510

    International headquarters tadiran telecom ltd. 18 hasivim street p.O.Box 7607 petach tikva 49170 israel tel. +972-3-9262000, fax. +972-3-9262310 http://www.Tadirantele.Com usa headquarters tadiran telecom, inc. 4 tri harbor court port washington, ny 11050 tel. +1-516-632-7200, fax. +1-516-632-7210 ...