Monobloc 125m power led power button o u t p u t 1 o u t p u t 2 i n p u t o u t p u t serial number 220-240v ~ 50-60hz fuse: t3.15a l 250v made in united kingdom monobloc 125m fuse carrier output socket loudspeaker terminals ac supply socket input socket 125 1234567 contents 0 2 w e l c o m e 0 8 k...
We are convinced it will give you many hours of listening pleasure. The 125m is a very powerful, high-quality, single-channel power amplifier (often referred to as ‘monobloc’) with an output of outstanding clarity and purity. It complements our pa20r and pa10 preamplifiers in performance and appeara...
Capacitors, which also block some of the low- frequency signal. In the 125m, a feedback circuit eliminates dc offset voltages and allows the signal path to be direct coupled without any capacitors.This arrangement, which we at tag mclaren audio call ‘straight line technology’, is easy to describe bu...
‘straight line technology’ with direct coupled signal and feedback paths high-quality audio components precision metal-film resistors cerafine power supply capacitors epoxy glass circuit board rated 125 w, typically 145 w into 8 Ω continuous (rated 200 w, typ. 240 w into 4 Ω and rated 275 w, typ. 32...
Use high-quality loudspeaker cable terminated in bfa plugs (1) to connect the red terminal of your right loudspeaker to the red terminal marked output 1 on the back of your 125m (2) . Then connect the black terminal of your loudspeaker to the black terminal marked output 1 on the back of your 125m. ...
Press the power button in. The blue power led will come on. Wait for about 10 seconds for the muting system to switch off (1) . Start playing your sound source. Turn up the volume, sit back and enjoy the music. Switch on getting started 12 1. The output is muted when the power is switched on to allo...
Loudspeaker terminals the ac mains supply normally operates at either 50 or 60 hz (depending on which country you are in). Under some circumstances, this can cause an audible hum in your loudspeakers. Should you have any problems with hum in your system, please contact your retailer. To minimise the...
We recommend that you use loudspeaker cables terminated in bfa plugs or spade terminals. These plugs are designed to fit the terminals on the back of the 125m (1) . The bfa plug and socket ensures that you cannot touch the high-voltage output conductors. Screw the knob of the terminal all the way in...
Your 125m is a single-channel amplifier and can only accept a mono input. If you want to use the125m for stereo, you will need one for each channel. Connect the left output of a preamplifier (such as our pa20r) to input on one of the 125ms and the right output on the preamplifier to input on the oth...
To improve the sound further, you can use separate amplifiers for high and low frequencies. This will allow you to increase the volume without distorting the sound. As each amplifier is operating in a smaller bandwidth, intermodulation distortion may also be reduced. Connect the output of one channe...
23 care and maintenance there is a fuse in the power socket on the back of your 125m. To change the fuse, unplug the power cable and pull out the fuse carrier drawer (1) . The fuse carrier contains a spare fuse; this is the first one that you see when you open the carrier. There are no other user-se...
25 technical data this section is for those of you who really want to know the ‘insides’ of your 125m. You will not miss out on any of the functions or performance of your 125m if you choose not to read any further. 125 w into rated load impedance (8 Ω ) 200 w into 4 Ω and 275 w into 2 Ω for short p...
27 technical data technical data 26 power consumption dimensions (including feet, terminals and controls) we reserve the right to alter design and specification without notice specification may vary for different countries less than 300 w 445 mm wide 75 mm high 333 mm deep ac supply voltage 0.1 hz –...
International standards 28 *115 v units are fitted with 4 mm terminals. They comply with 73/23/eec, iec65 and en60065 in all other aspects your 125m meets or exceeds all the legal requirements listed below: directives safety emc emissions emc immunity 89/336/eec emc directive (as amended by 93/23/ee...
