- DL manuals
- TAGnology
- Door locks
- SmaFinger
- User Manual
TAGnology SmaFinger User Manual
Summary of SmaFinger
Page 2: Smafinger
Smafinger promag rev.A 2 s mafinger is a fingerprint reader developed on the so-call contactless smart card 13.56 mhz rfid technology. The integration of biometric technology by fingerprint identification and 13.56mhz rfid technology make smafinger be capable of biometric and contactless performance...
Page 3: Smafinger
Smafinger promag rev.A 3 mifare ® application directory (mad) support: smafinger support the mad format card, the mad (mifare® application directory) standard proposes the introduction of common data structures for card application directory entries. Smafinger reader should take advantage of this fe...
Page 4: Smafinger
Smafinger promag rev.A 4 user-data format smafinger will send out the data following the format as below, the user data length defined by the data-info. At wiegand output format, the data output length is fixed (defined by number of bits), so the user data would be cut if longer than number of bits,...
Page 5: Smafinger
Smafinger promag rev.A 5 wires assignment color symbol i/o description red vcc in power input : dc 7.5v~12v black gnd in power ground white data 1 out wiegand data 1 signal / aba tk2 clock (strobe) green data 0 out wiegand data 0 signal / aba tk2 data yellow txd out rs232 txd (to host rxd) blue rxd ...
Page 6: Smafinger
Smafinger promag rev.A 6 mifare reader utility 1. Mifare settings: mad-aid: (default=4703) mad application identifier number is authorized and assigned by mifare.Net upon the customer’s request for registered application identifier in a mifare® application open system (aid: 0000h~ffffh). Or it is al...
Page 7: Smafinger
Smafinger promag rev.A 7 used card (not issued by "mifare card issuer") you have to indicate the data position in the card, when the card is not issued by "mifare card issuer" software. And you must set the "offset" (max 255, and base from zero) form the beginning of sector and set your data "length...
Page 8: Smafinger
Smafinger promag rev.A 8 2. Reader settings reader id : (default=0) smafinger reader id for multi link application. (id: 0~99). Interface : (default=wiegand) smafinger can be set as wiegand , rs232 or aba-tk2 output. Read mode: (default=card data only) a. Card data only: read card sector data only; ...
Page 9: Smafinger
Smafinger promag rev.A 9 3. Led / buzzer settings new smafinger support the led/alarm configuration. Setting the led/buzzer to indicate the system status for end-user. Enable rs232 command set control: (for 19200,n,8,1 only) rs232 led/buzzer command set frame as below: stx j number (0~9) cr 02h 4ah ...
Page 10: Smafinger
Smafinger promag rev.A 10 brown wire = inactive ( or card is invalid): show led color and beeps to indicate the end-user when brown wire = inactive, or card was failed by smafinger reader. Brown wire = active: show led color and beeps to indicate the end-user that brown wire = active signal from hos...
Page 11: Smafinger
Smafinger promag rev.A 11 4. Wiegand setting: number of bit s is to set the wiegand output type you want to meet your host (or terminal). It can be 26 to 128 (default=26). Include reader id 1 is to set the wiegand output data to include reader id when it is enabled. (default=disable). Bit sequence i...
Page 12: Smafinger
Smafinger promag rev.A 12 5. Aba-tk2 settings number of digital: set number of digital codes for tk2 output. (default=10) add reader id: add reader id into tk2 data. (default=disable) sequence: set the tk2 data sequence. (default=msb first) data conversion: select card data format to convert , a. Bi...
Page 13: Smafinger
Smafinger promag rev.A 13 6. Rs232 setting: baudrate can be set 2400bps~57600bps (default=19200bps) data sequence can be set "lsb" first (default) and "msb" first. Package 2 is to set the output data packet to include header, reader id, data length, cr, lf and trailer. (header:00h~ffh, trailer : 00h...
Page 14: Smafinger
Smafinger promag rev.A 14 test smafinger reader after configuration after smafinger configuration is completed you may use mifare reader utility "test" function to test the smafinger to see if the configuration is done correctly. 1. After the configuration on the mifare reader utility software is ma...
Page 15: Smafinger
Smafinger promag rev.A 15 annex a. Hardware specification smafinger major feature mifare ® application directory reader access control & security card type iso14443a, mifare class 1 (mifare ® 1k, mifare ® 4k for mad1/mad2) rf frequence 13.56mhz rf distance 2 50mm (using the mfa01 mifare ® card of gi...
Page 16: Smafinger
Smafinger promag rev.A 16 annex b. Wiegand interface the data 1 and data 0 signals are held at a logic high level unit, the reader is ready to send a data stream. The reader places data as asynchronous low-going pulses on the data 1 or data 0 lines to transmit the data stream to host. The data 1 and...
Page 17: Smafinger
Smafinger promag rev.A 17 annex c. Aba tk2 interface the timing for card present, clock (strobe) and data , example as below: 0 0 0 . . . 0 1 1 0 1 0 0 1 . . . 0 0 0 leading zero data trailing zero strobe width approximately 25~50% of bit time bit time 40ips (min:280us, typ:330us, max:480us) /data /...
Page 18: Smafinger
Smafinger promag rev.A 18 annex d. Rs232 interface connect the rs232 wires, example as below: host/terminal optional: external led/buzzer control (brown) (red) gnd (black) smafinger gnd gnd txd (yellow) 9~12vd.
Page 19: Smafinger
Smafinger promag rev.A 19 annex e. External led/buzzer control smafinger supports the external led/buzzer control for terminal (or host) to prompt end-user the card data is invalid or valid. Use brown wire to control the led/buzzer of smafinger examples as below: (active high) (1) show external inva...
Page 20: Smafinger
Smafinger promag rev.A 20 annex f. Secure mounting installation 1. Attach the bottom plate label on the target position. Drill the holes to match the bottom plate then fix smafinger reader. 2. After fixing smafinger with attached screws (using the l-shape spanner), apply screw cover plate for comple...
Page 21: Smafinger
Smafinger promag rev.A 21 annex g. Order information for sf500 part number include description sf500p-00 sf500 fingerprint usb programmer sf500-00 mf700kit was-t0029 power adaptor sf500 configurable reader mf700 reader kit rs232 cable for reader kit dc power adaptor for reader kit sf500sk-00 pcr310u...
Page 22: Smafinger
Smafinger promag rev.A 22 annex h. Order information for sf600 part number include description sf600p-00 sf600 fingerprint usb programmer sf600-00 mf700kit was-t0029 power adaptor sf600 configurable reader mf700 reader kit rs232 cable for reader kit dc power adaptor for reader for reader kit sf600sk...
Page 23: Smafinger
Smafinger promag rev.A 23 annex i. Webisp - firmware upgrade utility smafinger also supports the isp (in-system program) function to upgrade the reader’s firmware. Install the webisp (include in cd-rom) in your windows system first (it may need to reboot your system) and follow the steps as below: (...
Page 24: Smafinger
Smafinger promag rev.A 24 step 4: wait for the updating to finish. And repeat step 2 to update other readers or programmers. Step 5: check "upgrade & update files" list to download the new and related software or utility to meet the updated firmware. Note: click the new software or utility at "upgra...
Page 25: Smafinger
Smafinger promag rev.A 25 annex j. History rev a: october 26, 2006 initial smffinger configurable sector reader..