Summary of 289
Page 1
User manual tahoe 289 e3/t3/ethernet bridge.
Page 3
User manual tahoe 289 e3/t3/ethernet bridge.
Page 4
Ii tahoe 289 e3/t3/ethernet bridge tahoe 289 e3/t3/ethernet bridge user manual firmware version 1.0.3 published january 2008 ©2005-2008 tahoe. All rights reserved. Trademarks of other companies are used only for explanation and to the owner’s benefit, without intent to infringe. The specifications a...
Page 5
Iii tahoe 289 e3/t3/ethernet bridge safety instructions read the following safety notices before installing or operating the device: this warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electr...
Page 6
Iv tahoe 289 e3/t3/ethernet bridge contents introduction................................................................................................................................... 1 g.703 interface .................................................................................................
Page 7
V tahoe 289 e3/t3/ethernet bridge preface about this manual this manual contains following chapters: chapter 1, introduction an overview of tahoe 289 chapter 2, management the ways to access and manage the device chapter 3, control and settings the device settings available for the user chapter 4, s...
Page 9
Tahoe 289 e3/t3/ethernet bridge introduction tahoe® 289 bridges allow connecting two lans over an e3 / t3 (ds3) line. They are a cost-effective alternative to expensive e3 / t3 routers. Bridges are transparent, that is both interconnected networks appear as a single lan, as if both were plugged into...
Page 10
Tahoe 289 e3/t3/ethernet bridge ethernet interface the ethernet interface used for local network (lan) connection. It may work at speeds of 10 mbps (10base-t) or 100 mbps (100base-tx), in full-duplex or half-duplex mode. The mode of operation is selected automatically, although a specific setting ca...
Page 11
Tahoe 289 e3/t3/ethernet bridge management the tahoe 289 bridge is equipped with an lcd display/keypad and a serial console (rs232) con- nector. Both give equivalent access to device settings and statistics. All setting adjustments take immediate effect. Settings have to be saved before restart with...
Page 12
Tahoe 289 e3/t3/ethernet bridge tahoe 289 statistics > g.703 settings total data rate 0kbps ethernet settings tx data rate 0kbps advanced options rx data rate 0kbps reset counters tx frames 0 restore settings rx frames 0 save settings frame errors 0 reboot ethernet state 100baset-fd mdix uptime 0d 0...
Page 13
Tahoe 289 e3/t3/ethernet bridge control and settings device settings are available from the lcd menu and through the serial console. G.703 settings serial e3 / t3 (ds3) interface settings. Cir committed information rate. Limits the transmit data rate to a specified value from 512kbps up to full link...
Page 14
Tahoe 289 e3/t3/ethernet bridge loopback enables serial loop back (for testing purposes). The following modes are available: local local loop back remote (line) remote loop back (not using framer) remote (frame) remote loop back (using framer) this setting is not saved. Ethernet settings ethernet in...
Page 15
Tahoe 289 e3/t3/ethernet bridge transmit queue changes the size of the ethernet transmit queue with 64kb (32 frames) step. May be used to adjust latency in a heavily-loaded network. Reset connection resets the ethernet interface and reinitializes auto-negotiation if enabled. Advanced options advance...
Page 16
Tahoe 289 e3/t3/ethernet bridge save settings stores settings to nonvolatile memory. Reboot reboots the device..
Page 17
Tahoe 289 e3/t3/ethernet bridge statistics the following bridge statistics are available from the lcd menu and through the serial console. Name description total data rate total data rate used in kbps. Tx data rate transmit data rate used in kbps. Rx data rate receive data rate used in kbps. Tx fram...
Page 18
0 tahoe 289 e3/t3/ethernet bridge.
Page 19
Tahoe 289 e3/t3/ethernet bridge appendix a, troubleshooting problem possible solutions serial interface is connected but there is no link make sure rx and tx connectors are not swapped. Make sure a link partner is connected and properly configured wan link is detected at only one end make sure both ...
Page 20
Tahoe 289 e3/t3/ethernet bridge appendix b, technical specification throughput e3 34.368 mbps t3 (ds3) 44.736 mbps memory 16mb, sdram @100mhz connectors g.703 (rx, tx) 2x bnc, unbalanced 75 ohm ethernet rj45 console db-9/m network protocols hdlc ethernet interface 10/100base-t, rj45 connector serial...
Page 21
Tahoe 289 e3/t3/ethernet bridge appendix c, declaration of conformity tahoe piotr kaczmarzyk ul. Hercena 3/5 50-453 wrocław we declare that the product tahoe 289 complies with the regulations of the following european directives: 73/23/eec low voltage safety requirements 89/336/eec emc requirements ...
Page 22
Tahoe 289 e3/t3/ethernet bridge.
Page 24
Hercena 3-5 50453 wrocław, poland phone: +48 71 344 26 37, fax: +48 71 344 26 42 www.Tahoe-group.Com.