- DL manuals
- Taiden
- Projector Accessories
- TES-5600
- Installation And Operating Manual
Taiden TES-5600 Installation And Operating Manual
Summary of TES-5600
Page 1
Digital infrared wireless classroom audio system installation and operating manual v 1.9.
Page 2
Remarks: all rights reserved for translation, reprint or reproduction of this document. Contents may change without prior announcement. All technical specifications are guideline data and not guaranteed features. Taiden is not responsible for any damage caused by improper use of this manual. The equ...
Page 3
Important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. 6. The main...
Page 4
Important safety instructions attention: installation should be performed by qualified service personnel only in accordance with the national electrical or applicable local codes. Power disconnect: units with or without on – off switch have power supplied to the unit whenever the power cord is inser...
Page 5
Lithium battery safety precautions to change battery please power off and take off the battery immediately. Keep the battery away from heat sources to prevent fire or explosion. Do not use a battery that is leaking, deformed, discolored or overheats. Take extra precautions to keep a leaking battery ...
Page 6: Contents
Contents installation & user guide .........................................................................................................Viii chapter 1 system introduction ................................................................................................... 1 1.1 overview .............
Page 7
3.4.1 ceiling mounted ........................................................................................................................................................ 23 3.4.2 tripod mounted ........................................................................................................
Page 8
8.6 power adapter ........................................................................................................................................................... 58 8.7 charging unit ............................................................................................................
Page 9
Installation & user guide about this manual: this manual is a comprehensive guide to the installation and operation of taiden tes-5600 series digital infrared wireless classroom audio system. It includes the detailed description of the function and interface of the tes-5600 system components, system...
Page 10
Installation & user guide this manual is applicable to: digital ir wireless system main unit tes-5600ma/02p digital infrared wireless system main unit (supports 2 wireless microphones, built-in amplifier, supports 4 speakers, with phantom power) tes-5600mau/02p digital infrared wireless system mai...
Page 11
Chapter 1 system introduction 1.1 overview taiden tes-5600 series product is a digital infrared wireless classroom audio system. This system provides an ideal audio solution for teaching environment thanks to its capabilities of anti-interference, privacy assurance, easy-manageability and audio clar...
Page 12
Tes-5600mb/02p digital infrared wireless system main unit (supports 2 wireless microphones, with phantom power) tes-5600mbu/02p digital infrared wireless system main unit (supports 2 wireless microphones, usb interface for digital audio input/output, with phantom power) digital infrared receiver t...
Page 13
1.2 functions and features 1. The world’s first digital infrared wireless classroom audio system operating taiden diratc technology - digital infrared audio transmission and control technology 2. Audio clarity world pioneering infrared technology enables excellent audio quality: frequency response: ...
Page 14
1.3 system technology 1.3.1 basic system concept the system composition of tes-5600 digital infrared wireless classroom audio system is shown in figure 1.2. It is composed of: digital infrared wireless microphones digital infrared wireless main unit for system control digital infrared receiver...
Page 15
1.4 factors impacting infrared signal transmission to benefit from the advantages of a digital infrared wireless classroom audio system the signals should be transmitted undisturbed. This is achieved by using digital infrared receiver well positioned and sufficient in quantity to ensure uniform and ...
Page 16
Chapter 2 digital ir wireless system main unit 2.1 overview tes-5600m series digital infrared wireless system main unit is the heart of the tes-5600 wireless classroom audio system. The main unit can be connected to digital infrared receivers and recording devices and: display system function conf...
Page 17
2.2 functions and indications front panel of tes-5600m main unit rear panel of tes-5600ma/p main unit rear panel of tes-5600mau/p main unit rear panel of tes-5600mb/p main unit rear panel of tes-5600mbu/p main unit figure 2.1 digital infrared wireless system main unit 7.
Page 18
Figure 2.1: 1. “power” button and indicator 2. Menu display 128×36 oled, displays main unit status and configuration menu. 3. Knob for menu operation； for master volume control. 4. Receiver interfaces (1-4, bnc) 5. Device usb interface for firmware upgrade 6. Mic/line in (φ6.4mm, balance/dif...
Page 19
2.3 installation tes-5600m series digital infrared wireless system main unit is half-rack width and can be fixed in a standard 19-inch cabinet single or for two main units abreast. Installation of single main unit first unscrew the lateral screws ① from the housing. Then fasten the brackets ② and ③ ...
Page 20
2.4 connection several typical system connections of tes-5600m series main unit will be introduced in this section, including connection: to other auxiliary devices to recorder device to speaker to central control system 2.4.1 to other auxiliary devices digital infrared wireless system main unit can...
Page 21
2.4.4 to central control system tes-5600m has the functions of microphone controlling and volume adjusting. Also, taiden tes-5600 digital infrared wireless classroom audio system and taiden hcs-6100 intelligent central control system can be joined together seamlessly, connecting various devices, har...
Page 22
2.5 configuration and operation digital infrared wireless system main unit can be configured and set up through menu operation with knob. All menu items operation will be introduced one by one in this section. A) starting initialization switch on and press the "power" button, the tes-5600m digital i...
Page 23
2.5.2 line in vol. Adjust the volume of line in, range: -∞ (mute), -30 db to 0 db. 1. Press the knob to enter the line in selection interface; 2. Rotate the knob to select between line in 1 and line in 2, and then press the knob to enter; 3. Rotate the knob to adjust the volume and then press the kn...
Page 24
2.5.6 line in 1 set. 1. Press the knob to enter the setting interface; 2. Rotate the knob to select a type between line in and mic in, if select “line in”, press the knob to confirm; if select “mic in”, press the knob to enter the phantom power set up. 3. Rotate the knob to select on or off and then...
Page 25
D) protection overload protection: activated when the output of the amplifier is overloaded, and the oled displays “pa overload”; bnc protection: activated when bnc short circuit or other unusual circumstance happens, the oled displays “bnc unnormal”; alarm function: activated when a high leve...
Page 26
2.6 usb link tes-5600mu series main unit has a built-in usb audio (2 channels, 16bit, 44.1khz) which can be connected to the computer through usb cable (software requirement: win7 or higher) for digital audio input/output. Tes-5600m/p main unit cooperating with the tes-5603(b) can realize remote ppt...
Page 27
2.6.2 digital audio input when the tes-5600mu main unit is connected to computer with usb cable, lossless sound can be recorded during class on computer. Using the recording software or the third party communication software, such as recorder, skype and so on, functions like recording, remote instru...
Page 28
2.6.3 digital audio output the tes-5600mu main unit can be connected to the computer for digital audio output. Please adjust and test the tes-5600m usb link to a suitable volume when using for the first time. Adjust method: open the control panel-sound (or right click the volume icon on the taskbar ...
Page 29
2.6.4 ppt-page switch the tes-5600m/p main unit cooperates with the tes-5603(b) microphone to realize remote ppt-page switch control. See 5.4.3 . 19.
Page 30
Chapter 3 digital infrared receiver 3.1 overview the digital infrared receiver receives the infrared signals from the digital infrared wireless microphone, and sends the signals to the main unit. It can be mounted onto the ceiling. Reception angle: vertical 150°(±75°); horizontal 360°. Reception ran...
Page 31
3.3 position planning 3.3.1 precautions in planning the digital infrared receiver due to strict demands on intensity and stability of infrared signals in an infrared wireless classroom audio system, please read section 1.4 carefully and take all aspects of infrared signal transmission into considera...
Page 32
3.3.2 example for planning the receiver the reception angle of the tes-5600r is 150°in vertical and 360°in horizontal. For a good reception, please plan the receiver according to the teaching environment. 【8m×8m classroom】 in an 8m×8m classroom, one tes-5600r receiver can be mounted on the ceiling i...
Page 33
3.4 installation 3.4.1 ceiling mounted 3.4.1.1 ceiling mounted 1 ① m3 screw ② fixing bracket ③ rubber plug ④ hard ceiling (such as concrete ceiling) ⑤ tes-5600r(n) digital infrared receiver figure 3.7 tes-5600r(n)digital infrared receiver ceiling mounted 1 mounting steps: step 1: position the fixing...
Page 34
3.4.1.2 ceiling mounted 2 ① m3 screw ② fixing bracket ③ nut ④ ceiling ⑤ tes-5600r(n) digital infrared receiver figure 3.8 tes-5600r(n) digital infrared receiver ceiling mounted 2 mounting steps: step 1: position the fixing bracket on the ceiling according to the installation location of the tes-5600...
Page 35
3.4.2 tripod mounted ① tripod-mounted stator ② m3 screw ③ nut ④ fixing bracket ⑤ tes-5600rzj (with flexible tube) ⑥ tes-5600zj2 figure 3.9 tes-5600r(n) digital infrared receiver tripod mounted mounting steps: step 1: fix the fixing bracket onto the tes-5600rzj with m3 screws; step 2: fix the tripod-...
Page 36
3.4.3 wall mounted (adjustable angle) ① tripod-mounted stator ② m3 screw ③ nut ④ fixing bracket ⑤ tes-5600rzj (with flexible tube) ⑥ wall figure 3.10 tes-5600r(n) digital infrared receiver tripod mounted mounting steps: step 1: fix the fixing bracket onto the tes-5600rzj with m3 screws; step 2: put ...
Page 37
3.5 connecting to main unit connect the receiver to the main unit with rg-59 coaxial-cable (see figure 3.11). Figure 3.11 digital infrared transceiver connecting to digital infrared wireless system main unit note: the correctness of the cable connection can be ensured when the transceiver indicato...
Page 38: Unit
Chapter 4 economical digital infrared wireless system combo unit 4.1 overview the economical digital infrared wireless system combo unit integrates the digital infrared wireless system main unit and the digital infrared receiver. It comes with built in amplifier and supports 1 (tes-5630ma) or 2 (tes...
Page 39
4.3 installation 4.3.1 ceiling mounted 4.3.1.1 ceiling mounted 1 ① tes-5630m ② ceiling-mounting kit ③ mounting hole (drilled on the ceiling) ④ ceiling figure 4.3 tes-5630m ceiling mounted 1 mounting steps: mounting steps: step 1: install the ceiling mounting kit at the top of the tes-5630m; step 2: ...
Page 40
4.3.1.2 ceiling mounted 2 ① m3 screw ② hard ceiling mounting bracket ③ rubber plug ④ ceiling ⑤ tes-5630m figure 4.4 tes-5630m ceiling mounted 2 mounting steps: step 1: position the mounting bracket on the ceiling according to the installation location of the tes-5630m and mark the positions of the d...
Page 41
4.3.2 tripod mounted 4.3.2.1 ceiling mounted 1 ① hard ceiling mounting bracket ② tes-5630m ③ tes-5600zj2 (should be ordered separately) figure 4.5 tes-5630m tripod mounted 1 mounting steps: step 1: put the bracket on the bottom of the tes-5630m and fix it with rotation; step 2: aim the mounting hole...
Page 42
4.3.2.2 ceiling mounted 2 (adjustable angle) ① tes-5630m ② m3 screw ③ tes-5600rzj (with flexible tube) ④ tripod-mounted stator ⑤ tes-5600zj2 (should be ordered separately) figure 4.6 tes-5630m tripod mounted 2 mounting steps: step 1: fix the tes-5630m onto the tes-5600rzj with m3 screws; step 2: fix...
Page 43
4.3.3 wall mounted (adjustable angle) ① tes-5630m ② m3 screw ③ tes-5600rzj (with flexible tube) ④ wall figure 4.7 tes-5630m wall mounted mounting steps: step 1: fix the tes-5630m onto the tes-5600rzj with m3 screws; step 2: position the tes-5600rzj on the wall according to the installation location ...
Page 44
4.4 connection several typical system connections of tes-5630m economical digital infrared wireless system combo unit will be introduced in this section, including connection: to loudspeaker to other extension receiver (tes-5600r) to other auxiliary devices 4.4.1 to loudspeaker tes-5630ma has ...
Page 45
4.5 operation the operation of the tes-5630 economical digital infrared wireless system combo unit will be introduced in detail in this section. 1. Adjust the master volume rotate the vol. Knob on the top of the tes-5630m to adjust the volume of the loudspeaker, range: -30 db to 0 db, step: 1 db. 2....
Page 46
Chapter 5 digital infrared wireless microphone 5.1 overview tes-560x digital infrared wireless microphone is the basic devices for the user, divided into pendant type and handheld type. Different functions are available, depending on the microphone type. Functions include: speak and mute, frequency ...
Page 47
5.2 functions and indicators tes-5602a (front) tes-5602a (back) tes-5602a (bottom) tes-5603(b) (front) tes-5603(b) (back) tes-5603(b) (top) tes-5603(b) (bottom) figure 5.1 tes-5600 series digital infrared wireless microphone figure 5.1: 1. Microphone 2. Infrared transmitting glass 3. Battery/charge ...
Page 48
10. Charging port (usb) 11. Charging contacts 12. Selector button select which source (own, otr or line) will be controlled by the remote volume buttons; press and hold on this button to open/close the ppt mode. 13. Function button (f) for tes-5603, press and hold on this button to switch betw...
Page 49
5.3 infrared service area infrared light is directional invisible light. Infrared wireless microphone gets best sensitivity when it directly faces a receiver. The infrared glass on tes-5600 series digital infrared wireless microphone is designed to be at its best position to guarantee maximum emissi...
Page 50
5.4 operation the operation of the tes-5602a and tes-5603 digital infrared wireless microphones will be introduced in detail in this section. 5.4.1 tes-5602a (handheld type) tes-5602a handheld type digital infrared wireless microphone combines speaking, mute, and working mode setting all in one. Oth...
Page 51
6. Charging the tes-5602a is powered by a rechargeable lithium battery and it also can be charged via the usb port. When charging, it switches to external power supply mode automatically. The batt indicator indicates the charging status: 5.4.2 tes-5603(b) (pendant type) the tes-5603(b) pendant type ...
Page 52
2. Remote volume control tes-5603(b) supports remote volume control of own/otr/line in and own mute control when it works in 1.0 mhz or 2.3 mhz frequency channel. Remote volume control: a. Press the selector button to select a signal source and its indicator will be turned on; b. Adjust the volume b...
Page 53
Ppt mode own indicator on green off red b. Press the “▲/▼”button to turn pages of the ppt when ppt mode is on. 6. Alarm function press and hold simultaneously “selector” and “function” buttons to enable the alarm function, the 3 signal indicators (own/otr/line) turned on, and the oled of the main un...
Page 54
Chapter 6 accessories 6.1 power adapter tes-adp24v power adapter connect the tes-adp24v to the power adapter interface at the rear panel of the tes-5600ma digital infrared wireless system unit. Figure 6.1 tes-adp24v power adapter tes-adp24vn power adapter connect the tes-adp24vn to the power ada...
Page 55
6.2 dedicated cable receiver cable cbl5600 dedicated receiver cable is used to connect the digital infrared receiver and the main unit. It features one bnc connector. Available lengths: 10, 20，30, 40 or 50 meters. Outside diameter: φ5 mm; figure 6.6 cbl5600 dedicated receiver cable clb-spk speak...
Page 56
6.3 speaker hpa-2140 ceiling speaker ceiling mounting; cutout for mounting: 198 mm to 208 mm; dimensions: Ø 230×128 mm; power consumption: 8 Ω, 40 w; frequency response: 75 hz~20 khz; sensitivity: 90 db; weight: 1.7 kg figure 6.11 hpa-2140 ceiling speaker hpa-2160 ceiling speaker ceiling mountin...
Page 57
hpa-2240 wall-mounted speaker wall-mounted, equipped with u bracket; dimensions: 290×215×190 mm; power consumption: 8 Ω, 40 w; line voltage: 70~100 v (hpa-2240a) frequency response: 75 hz~20 khz; sensitivity: 90 db; weight: 3.4 kg figure 6.15 hpa-2240 wall-mounted speaker hpa-2280 wall-mounted s...
Page 58
6.4 tes-5600zj1 tes-5602a microphone stand: weight 0.5 kg, height 0.15 meter. Figure 6.18 tes-5600zj1 6.5 tes-5600zj2 figure 6.19 tes-5600zj2 tes-5600zj2 microphone/receiver stand is used to mount the tes-5600r(n) , tes-5630m(a) and tes-5602 microphone, its height can be adjusted from 1.1 m to 2.7 m...
Page 59
6.7 charging station tes-5600cs charging station tes-5600cs can charge a tes-5602a and a tes-5603(b) at the same time with tes-adp5v. Figure 6.21 tes-5600cs charging station tes-5602chg/09 charging station tes-5602chg/09 can charge nine tes-5602a microphones at the same time with tes-adp5v6a. Fi...
Page 60
6.9 tes-5600rzj tes-5600rzj is suitable for tripod or wall mounted of tes-5600r(n). length 115 mm weight 110 g figure 6.26 tes-5600rzj 50
Page 61: Chapter 7 Fault Diagnosis
Chapter 7 fault diagnosis some simple trouble-shooting instructions are provided in this chapter. If more serious faults arise, please contact a qualified technician. 7.1 digital infrared wireless microphone fault analysis solution cannot start up. The battery is not charged. (when using the lithium...
Page 62
7.3 usb link fault analysis solution no audio input/output. Detect usb link failed pull out and then insert the usb cable again. Tes-5600m usb link is not the current audio device select tes-5600m usb link as current audio device manually. Manifold usb devices in one hub tes-5600mu connects to a sin...
Page 63: Chapter 8 Technical Data
Chapter 8 technical data 8.1 system specification system performance conforms to iec 60914, the international standard for conference systems transmission characteristics ir transmission wavelength : 870 nm modulation frequency: 1 to 8 mhz protocol and modulation: dqpsk cabling and system limits rec...
Page 64
8.2 digital infrared wireless system main unit type tes-5600ma(u)/02p tes-5600mb(u)/02p discussion √ voltage dc 24 v (tes-adp24 v adapter) dc 15 v (tes-adp15 v adapter) static consumption 24 v，360 ma 15 v，375 ma line in +16 dbu line out +18 dbu maximal number of microphone 2 number of connectable re...
Page 65
8.3 digital infrared receiver type tes-5600r tes-5600rn voltage 12 v dc (supplied from tes-5600m) current consumption max. 45 ma mounting ceiling, tripod mounting inf rar ed d et ec tor wavelength 870 nm modulation method dqpsk carrier frequency 1-8 mhz communication area horizontal: 360° vertical: ...
Page 66
8.4 economical digital infrared wireless system combo unit type tes-5630m(a) voltage 24 v dc current consumption max. 260 ma maximal number of microphone 2 (tes-5630m); 1 (tes-5630ma) number of connectable receivers 1×bnc speaker interface max. 2×30 w (8 Ω) virtual: 2×23 w (8 Ω) weighted signal-to-n...
Page 67
8.5 digital infrared wireless microphone type tes-5602a tes-5603(b) discussion √ √ remote volume control -- √ voltage lithium battery or usb supply (5 v) lithium battery or usb supply (5 v) or aa alkaline cell (only tes-5603) current consumption ≤360 ma ≤160 ma inf rar ed em it ter /r ec ei v er wav...
Page 68
8.6 power adapter type tes-adp15v tes-adp24v tes-adp24vn tes-adp5v6a tes-adp5v mains voltage ac 100-240 v, 50 /60 hz output 15 v dc, 2.4 a 24 v dc, 2.7 a 24 v dc, 1.5 a 5 v dc, 6.0 a 5 v dc, 2.0 a cable length 3 m 2.8 m 1.0 m dimensions (mm) w x h x d 95 x 45 x 28 115 x 50 x 32 95 x 45 x 28 121 x 52...
Page 69
8.8 connection details audio cables chinch connector (male) pin ① signal + pin ② gnd 6.4 mm jack plug tip① balance/ unbalance signal + ring② balance/ unbalance signal - sleeve③ ground/ shield note: the line in of tes-5600m/p must be balance signal. If there is a unbalance signal, please turn it to...
Page 70
Appendix appendixⅠ: connect rg-59 coaxial-cable to tes-5600r 1. Strip 10mm insulation of cable sheaths, twist the braided shield into a bundle and cut off unnecessary mylar paper and insulation; 2. Open the cable clip, insert the conductor to the connection hole, and clip the braided shield and the ...
Page 71
Copyright by taiden last revision: 08/2017 taiden industrial co., ltd. 6/f, block b, future plaza, 6060 qiaoxiang rd, nanshan district, shenzhen, china p.C.: 518053 website: http://www.Taiden.Com.