Takenaka System FC1600FCL Instruction Manual - page 21
K11208a;21/36
- 21 -
[Description of CR data]
Bit
Abbrev.
Content
Logic
Remark
0
MENU
Disabled display of menu screen
1: Disabled (OFF)
1
BZ
Disabled buzzer output
1: Disabled (OFF)
2
PATTERN ON/OFF selection for test pattern
1: Test pattern ON
3
BIT
Selection of output data format
1: 8bit format
0: 10bit format
4
(Not used)
5
(Not used)
6
STRB-C
Enabled STRB signal output for continuous shutter
1: Enabled
7
Vinit2
Selection of trigger signal (Vinit2) polarity via CC1
1: Positive polarity
8
H-RESET Enabled H-reset in asynchronous operation
1: H-reset Enabled
9
BAUD
9600bps/19200bps selection for serial communication baud rate 1=19200bps
* 1
10 -
(Not used)
11 -
(Not used)
12 -
(Not used)
13 -
(Not used)
14 CCD0
(Not used)
15 DEFR
Request for reading out default value at next start-up
1: Request
* 1
(Note) All the items of the CR data are “0” as factory default.
The items marked with <* C> can not be changed by the communication command.
[Description of FR data]
Bit Abbrev
Content
Logic
Remark
0 ASYE
Selection of continuous/asynchronous shutter 1: Asynchronous (ASYNC)
1 PWCE Selection of enabled/disabled for pulse width
control
1: Enabled pulse width control
2 LEXE
Selection of high speed/low speed shutter
1: Low speed shutter
3 PSCE
Selection of normal scan/partial scan
1: Partial scan
4 DSCE (Not used)
5 -
(Not used)
6 -
(Not used)
7 -
(Not used)
8 ESP(0)
Externally designated shutter speed position
H'0 to H'9 or H'F
Where ESPE=1, externally
designated number from 0
to 9 (designated position)
is reflected. In case of H'F,
external shutter speed in
H unit is selected.
9 ESP(1)
10 ESP(2)
11 ESP(3)
12 ESPE
Validity of externally designated shutter speed 1: Valid
13 -
(Not used)
14 -
(Not used)
15 AGCE (Not used)
(Note)
All the items of the FR data are “0” as factory default.
(Example) If “MF=H’0008.0003” is displayed on the menu screen, the camera is in the following state (converting the
numbers to ones in binary system):
H’00=B’00000000, H’08=B’00001000 and H’03=00000011 are substituted to the above numbers.
CR=B’0000000000001000, FR=B’0000000000000011
………
CR(3)=FR(1)=FR(0)=1, All other bits = 0
(Where CR(n) and FR(m) represent the nth bit of CR and mth bit of FR respectively)
Based on 1 or 0 of these bits and the information in the above table, the user can know that the camera is in the
state of “8bit format”, “ASYNC” and “Enabled pulse width control”.
[Explanation]
The setting values (1 or 0 of respective bits) of (CR) and (FR) vary according to the change to be made using the switches
on the rear panel of the camera. The operation modes that cannot be changed by the RS-232C commands can be
changed by altering the bits of (CR) and (FR).
(Example 1) When a change is made from the continuous shutter mode
→
asynchronous shutter mode,
“MF=0000.0000” is replaced by “MF=0000.0001” (ASYE bit = 1).
(Example 2) When CR (0) is changed from 0
→
1 using a serial communication command, “ON” on the menu display is
replaced by “OFF” (MIND=1).