1. DL manuals
  2. Takenaka System
  3. Security Camera
  4. FS2300DV
  5. Instruction Manual

Takenaka System FS2300DV Instruction Manual

Manual is about: 2 Mega pixel Progressive Scan Color Camera

Summary of FS2300DV

  • Page 1

    N11a27;1/37 - 1 - video camera instruction manual 2 mega pixel progressive scan color camera fs2300dv ● we greatly appreciate your confidence choosing our takex ccd video camera. ● please read this manual and the attached guarantee certificate carefully and manage the camera properly. Keep this manu...

  • Page 2

    N11a27;2/37 - 2 - [revision history] version revised contents articles date document no. Remarks 1 1 st version -- initial version 2010-07-16 n10601 fs2300dv 2 2 nd version error correction 2011-06-21 n11311a 3. 3 rd version error correction 2011-10-27 n11a27 description of special remarks used in t...

  • Page 3

    N11a27;3/37 - 3 - 1. Features ● fs2300dv is a full frame shutter color camera incorporated with 2.01 megapixel, 1/1.8”-size ccd image sensor. ● a full frame shutter image can be obtained at a rate of 20 frames per second. ● the rgb 8 bit digital image signal output complying with camera link (base c...

  • Page 4

    N11a27;4/37 - 4 - 3. Description of each component (3-1) description of rear panel of camera panel to set up operation mode, electronic shutter speed and other parameters and to connect each output connector (3-2) camera connector (hrs hr10a-7r-6pb) the pin arrangement of the camera cable connector ...

  • Page 5

    N11a27;5/37 - 5 - [table of camera link bit assignment] (showing correspondence relation between before and after encoding) camera link port (node name) camera signal name i/o remark strobe clk o pixel clock lval ldv o horizontal synchronous timing fval fdv o vertical synchronous timing dval - o (fi...

  • Page 6

    N11a27;6/37 - 6 - (3-4) dvi-d output,hdmi connector (note) pin 17(+5v) are monitor wiring pins. Do not use of them for the purpose other than that. (note) this camera has dvi-d output. Images may not displayed when connected to hdmi input. (note) use the 1920 × 1080 ,60hz(rb)- conforming multiscan m...

  • Page 7

    N11a27;7/37 - 7 - [important] (note) make sure to turn off the power switch of the camera before connecting or disconnecting the camera cable. If the cable is connected or disconnected while the power is supplied, it may cause the camera troubles. (note) make sure to turn off the camera and connecte...

  • Page 8

    N11a27;8/37 - 8 - ● recommended timing of asynchronous shutter trigger signal (vinit signal) for preset shutter/pulse width control for the case of preset shutter mode, the negative logic pulse is applied within the width range from 1 h (one horizontal synchronous time) to 1ms as described below. Fo...

  • Page 9

    N11a27;9/37 - 9 - (4-3) other input/output circuit ● strobe signal output circuit the internal output circuit is shown in the right figure. (!) the strobe signal of this camera is 3.3v logic level. (4-4) strobe signal in continuous shutter mode the default setting is off (no strobe signal in continu...

  • Page 10

    N11a27;10/37 - 10 - (4-6) monitoring function for internal temperature of camera this camera is equipped with an internal temperature sensor to monitor the temperature inside the camera housing. This function makes it possible to use the camera in a safer way even in a harsh environment in terms of ...

  • Page 11

    N11a27;11/37 - 11 - (example 2) where td, the returned value of the temperature data, is “h’03fa” in the hexadecimal system, it is expressed in the binary system as follows: td=h’03f1=b’0000.0011.1111.1010 ∴ db=b’11.1111.1010 (only upper 10 digits of td are valid.) → dt=-6 ( ↓ refer to [explanation]...

  • Page 12

    N11a27;12/37 - 12 - electroni c shutter oper ation mode no shutter oper ation elec tr oni c shutter operation shutter swi tch = 0 shutter switch = 1 to 9 as ync hronous shutter l ow speed shutter high speed shutter preset shutter pulse width contr ol continuous shutter hi gh speed shutter 5. Various...

  • Page 13

    N11a27;13/37 - 13 - ・ the operation mode of the camera can be changed by changing the argument data of the serial communication command “h’21,h’22”. Communication command h’21 lsb msb enabled strb signal output 0 : off 1 : on h reset 0 : off 1 : on selection of cc1 polarity 0 : positive polarity 1 :...

  • Page 14

    N11a27;14/37 - 14 - fig. 5-2 conceptual diagram of gain and offset levels (5-3) level setting the level setting is mostly divided into the following two groups: ● gain setting this is to set the gain (amplification ratio) of the preamplifier between the ccd imaging device inside the camera to a/d co...

  • Page 15

    N11a27;15/37 - 15 - (5-5) data save and data read setting this camera incorporate nonvolatile memories and various operation mode settings and level settings can be stored on them. And the data set at each address is overwritten with the contents of nonvolatile memories at the time of power-on. Exec...

  • Page 16

    N11a27;16/37 - 16 - 6. How to change setting (6-1) how to set hypothetical shutter switch the shutter speed is determined mainly by the setting positions of the hypothetical shutter switch from “0” to “9”. It can be set by changing the argument data of the communication command “h’32”. Table 6-1 set...

  • Page 17

    N11a27;17/37 - 17 - ● menu display it can switch the menu displayed by osd function. Refer to section 6-6 for more information about the displayed menu. The osd menu can be switched by entering the argument [h’00 ~ h’04] to the communication command “h’20”. ● mgc setting (manual gain control) the ga...

  • Page 18

    N11a27;18/37 - 18 - ● red digital gain it can change the red digital gain when outputting camera link signal and rgb 8bit signal for the monitor. Variable range is approximately 0.01 to 4-fold when assuming 0x40 as reference 1-fold in a fixed-point system. Also, the sampling value (the average value...

  • Page 19

    N11a27;19/37 - 19 - ● serial communication baud rate the serial communication baud rate of this camera is fixed to 9600 bps. ● test pattern it outputs the color bar signal from the camera as the camera link output and monitor output. Refer to the section (4-5) “test pattern display function” for mor...

  • Page 20

    N11a27;20/37 - 20 - table 6-5 [osd menu 4] setting ● selection of operating cursor it can select the cursor to be changed and to display the settings. It can be changed by entering the argument [h’01 to h’04] to the communication command “h’45” as follows. H’01 : to display the data of cursor1 (whit...

  • Page 21

    N11a27;21/37 - 21 - ● setting of cursor 1(white) display/hide, shape setting it can set the shape of cursor 1. It can be changed by entering the argument [h’00 to h’03] to the communication command “h’40” as follows. H’00 : hide cursor h’01 : lattice-shaped cursor h’02 : box-shaped cursor h’03 : cro...

  • Page 22

    N11a27;22/37 - 22 - ● hide setting of the cursor (camera link output) it can hide the cursor for camera link output separately from the cursor for monitor output.. ● cursor movement it can move each cursor by entering an argument to the communication command h’48 as follows after setting the operati...

  • Page 23

    N11a27;23/37 - 23 - * m e n u 1 m e n u : o n g a i n : 1 2 0 / m g c o f f se t : 1 6 0 s . T im e : o f f ( 6 6 . 6 7 )m s s . F or m : a s y n c / h i g h s c a n : n o r m al m o n it o r : o n t c = 3 0 . 0 d e g m s = - s s = 0 f s 2 3 0 0 d v [ v x . X x ] (6-6) description of menu display by...

  • Page 24

    N11a27;24/37 - 24 - s.Time: the current shutter speed is displayed. The left number is h number (horizontal synchronous time unit / in the case of high speed shutter – range: 1 to 1023) or v number (vertical synchronous time unit / in the case of low speed shutter – range: 1 to 255 in decimal system...

  • Page 25

    N11a27;25/37 - 25 - 7. Serial communication control fs2300dv can be externally controlled via the camera link serial interface . (note) when the operation modes of the camera are changed by the communication functions, it takes some time to switch the modes. Carefully note that normal image may not ...

  • Page 26

    N11a27;26/37 - 26 - ・ do not send the character string to the camera that is not described in the instruction manual. It may cause a malfunction. Command (low 8bit) r/w byte functions default setting range h’00 r prohibited to use － － h’01 r camera version info. － － h’03 r prohibited to use － － h’04...

  • Page 27

    N11a27;27/37 - 27 - command (low 8bit ） r/w byte functions default setting range h’48 r/w cursor movement 01 ： ↑ 02 ： ↓ 03 ： ← 04 ： → － h’49 r/w operating cursor no. I to 4 h’01 h’00 ~ h’04 h’4a r/w moving amount of cursor 00: ± 1 01: ± 10 h’00 h’00 ~ h’01 h’4b r/w centering of cursor 0: off 1: on －...

  • Page 28

    N11a27;28/37 - 28 - control (low 8bit ） r/w byte functions default setting range h’d2 r operation mode status (high speed shutter /low speed shutter) － － h’d3 r operation mode status (pulse width control on/off) － － h’d4 r operation mode status (strobe signal on /off) － － h’d5 r operation mode statu...

  • Page 29

    N11a27;29/37 - 29 - 8. Timing chart ● pixel clock timing (common in various operation modes) [phase relationship between clock output and data] (note) the above timing represents the signal timing before being encoded to serial data by the channel link device on the side of the sending end (the part...

  • Page 30

    N11a27;30/37 - 30 - ● vertical timing: continuous shutter, no shutter 1 ve rtic al p erio d（1 v） ＝1 fram e ti me ineffective image duration (16) e ffec tive ima ge d urat ion ＳＴＲＢ Ｖ Ｄ （ i nt e rn al ve r ti ca l s y nc si gn a l ） ＦＶ ＡＬ ca m er a l in k i mag e o utp ut 1 2 3 4 5 1 2 36 0.13 1 Ｈ Ｄ e...

  • Page 31

    N11a27;31/37 - 31 - ● vertical timing: high speed/pulse width control/asynchronous shutter/without h-reset (note) strictly speaking, even if the same pulse width of vinit is applied, the shutter exposure time differs for the period corresponding to 1h width when the asynchronous shutter operation is...

  • Page 32

    N11a27;32/37 - 32 - ● vertical timing: high speed/preset shutter/asynchronous shutter/with h-reset ※ the detailed vertical timing of each effective image duration is the same as that of “vertical timing/continuous shutter, no shutter”. (note) the n (integer) in this chart represents the integer part...

  • Page 33

    N11a27;33/37 - 33 - ● vertical timing: high speed/pulse width control/asynchronous shutter/with h-reset Ｈ Ｄ Ｖ ｉｎ ｉｔ e xpos ure time ＦＶＡＬ （in tern al hori zont al sy nc s ign al） e n d o f e xp o s u r e ( s e n so r g a t e ) im age outp ut ＳＴ ＲＢ 24 7×p clk the period where it is regarded invalid to...

  • Page 34

    N11a27;34/37 - 34 - ● vertical timing: low speed (long exposure)/preset shutter/continuous shutter ＶＤ ＦＶ ＡＬ （ i n t e r n a l v e r t i c a l s y n c s i g n a l ） exposure time（ｎＶ ） i ma g e ( p) ／e x p o s u re t i m e image （ Ｐ－ １） imag e （Ｐ ） ima ge （Ｐ ＋１ ） i mage ( p+1) ／exposure ti me long exp...

  • Page 35

    N11a27;35/37 - 35 - 9. Notes [general notes] ● this equipment is not allowed to be used for medical purposes, detection of hazardous materials or any other operations of which performance may exert influence on human lives or safety. ● we assume no responsibility whatsoever for any incidental damage...

  • Page 36

    N11a27;36/37 - 36 - [countermeasures against heat] [fixing screw for the camera] 10. Specifications [specifications] imaging device progressive scanning, interline transfer ccd 1/1, 8 inch size unit cell size: 4.4 µ m(h) × 4.4 µ m(v) square grid pattern number of effective pixels 1628 (h)×1236(v) re...

  • Page 37

    N11a27;37/37 - 37 - 11. External dimensions [external dimensions] 36 3 1 8 70.5 6.5 18 18 φ 2 8 12 53 c mount 2- m3 de pth4 2- m3 de pth3 （four faces ） （bottom face ） fig.11-1 fs2300dv external views.