TAL Dolce 297-029 Manual

Summary of Dolce 297-029

  • Page 1

    World imports lifetime limited warranty the retailer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, exclu...

  • Page 2

    Safety rules..................................................................................................................................... Unpacking your fan ......................................................................................................................... Installing yo...

  • Page 3

    1. Safety rules 1. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box before beginning. 2. All wiring must be in accordance with the national electrical code and local electrical codes. Electrical installation should be performed by a qual...

  • Page 4

    Unpacking your fan 2. Warning do not install or use fan if any part is damaged or missing. Call toll free 1-877-902-5588 unpack your fan and check the contents. You should have the following items; . 1 fan blades (5) 2. Canopy assembly 3. 4. 5. Fan motor assembly blade arms (5) ball/downrod assembly...

  • Page 5

    3. Installing your fan tools required p h i l l i p s s c r e w d r i v e r , s t r a i g h t s l o t screwdriver, adjustable wrench, step ladder, and wire cutters. Mounting options if there isn't an existing ul listed mounting box, then read the following instructions. Disconnect the power by remov...

  • Page 6: Hanging The Fan

    Hanging the fan remember to turn off the power. Follow the steps below to hang your fan properly: step 1. Remove the decorative canopy bottom cover from the canopy by turning the cover counter clockwise.(fig. 5) step 2. Remove the hanger bracket from the canopy by loosening the two screws on the bot...

  • Page 7

    5. Pin in locked position motor collar motor wires ball/downrod assembly ceiling canopy tighten screws firmly figure 7 hanger pin locking pin collar cover canopy cover make the electric connections warning: to avoid possible electrical shock, be sure electricity is turned off at the main fuse box be...

  • Page 8: Attaching The Fan

    6. Figure 11 outlet box hanger bracket canopy canopy cover screws supply circuit ground conductor outlet box green ground lead ground to downrod b l a c k w h it e white w h it e white black b l a c k black blue b l u e g r e e n figure 10 white white blue black on on attaching the fan blades step 1...

  • Page 9

    7. Rubber washer blade arm figure 12 blade screws figure 13 motor blade arm slot tab all blades are grouped by weight. Because natural woods very in density, the fan may wobble even though the blades are weighed equally. The following procedure should correct most fan wobbling problems. Check after ...

  • Page 10: Installing The Light Plate

    Installing the light plate step 1. Remove 1 of the 3 screws from the mounting ring and loosen the other 2 screws. (do not remove) step 3. Place the key holes on the light plate over the 2 screws previously loosened from the mounting ring, turn light plate until it locks in place at the narrow sectio...

  • Page 11

    9. Operating your transmitter restore power to ceiling fan and test for proper operation. 1. " lo, med, hi" buttons: these three buttons are used to set the fan speed as follows: lo= low speed med= medium speed hi= high speed 2. "fan off" button: this button turns the fan off. 3. The "light/dimmer" ...

  • Page 12

    Care of your fan 10. Here are some suggestions to help you maintain your fan 1.Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. (it is not necessary to remove fan from cei...

  • Page 13

    Problem fan will not start. Fan sounds noisy. Remote control malfunction: solution 1.Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. Caution: make sure main power is off. 3. Check to make sure the dip switches from the tra...

  • Page 14

    These are approximate measures. They do not include amps and wattage used by the light kit. Rpm cfm n.W. G.W. C.F. 52" 120 3.05' kgs kgs 120 120 fan size speed volts amps watts low medium high specifications 12. Distributed by your other warehouse, llc 12100 little cayman dr. Baton rouge, la 70809 2...