Summary of TLM200A
Page 1
Talamex inflatable boats owner’s manual lankhorst taselaar b.V..
Page 2: General Information
2 contents page general information 3 hin-hull identification number 4 assembly and disassembly 6 using the boat 9 repair procedure 13 warranty 14 declaration of conformity 16.
Page 3: General Information
3 general information congratulations on the purchase of inflatable boat. Please read this manual carefully before inflating, assembling or using your boat. Also study carefully the manual supplied with your outboard engine. Familiarise yourself with the features of the boat and the engine and ask f...
Page 4: Specifications
4 specifications outer length outer beam tube dia. Max.Load max.Power weight model design cat. Cust.Code model. Code c m c m c m pers. Lbs/kg kw/hp kg tlm200a c tlm ta 200 124 36 2 654 / 297 2.98 / 4 26.78 tlm230l c tlm tb 230 138 36 3 682 / 309.20 3.97/5 28.4 tlm240a c tlm tc 240 138 36 3 819 / 371...
Page 5: Steering
5 the hin is visible at the starboard side of the transom. Do not alter, cover or remove the hin. It may void the warranty and can get you into legal problems. Record the hin of your boat in the designated place on the declaration of conformity’ in this manual. Also write it down in a safe place. Th...
Page 6: Assembly And Disassembly
6 · passengers: unnecessary people off the boat. · all electrical equipment: off. · fill less than rated capacity of tank, allow for fuel expansion. · follow engine manufacturer’s recommendations for types of fuel and oil. · refer to outboard motor manual for details. Assembly and disassembly attent...
Page 7
7 a-tube valve b-keel valve location of valve 4. When using the boat for the first time, fully inflate it by attaching the foot pump to each of the valves, one at a time, and when pumping, ensure that a balance of pressure between the chambers is maintained until the boat has been fully inflated. Wh...
Page 8
8 1. Unfold and stretch out the floor onto the bottom of the boat, edging it under the half-inflated tubes and against the transom. The valve must face upwards. 2. Inflate the floor up to ¾. 3. Finish inflating the boat. 4. Finish inflating the floor. 5. Fully inflate the keel. Assembly for boats wi...
Page 9: Disassembly
9 2. Slide an oar (a) under the bottom of the boat to raise the floor boards (b) over the flat surface. Attach side joiners (c). Repeat the procedure on opposite side of the boat. In case of more than one joiner on each side, start with one long, one short joiner on one side and with one short and o...
Page 10: Cleaning Procedures
10 cleaning procedures rinse your boat when possible, after each use. At the end of a season, wash it out in soapy water or with washing-up liquid. Rinse, let dry then apply talcum powder before folding up the boat. Store in a dry place. Important : do not use a vinyl preserving agent on fabric surf...
Page 11: Inflation - Deflation
11 in the water or allow a swimmer to approach the stern of the boat while the engine is running. 7. Due attention should be given to winds and tides, which can change and therefore affect fuel consumption. 8. When boating in unknown waters, it is always a wise precaution to obtain local knowledge b...
Page 12: Loading
12 4. When inflating, maintain a balance of air between air chambers to prevent damage to air chamber bulkheads. Loading 1. Do not exceed the weight carrying capacity indicated on the boat identification plate. 2. Each person in the boat should wear a life jacket (personal flotation device). 3. Oars...
Page 13
13 1. The inflatable must be empty when it is towed by another boat. The towing line should be secured to the "d"-rings on each side of the inflatable. The inflatable must be under constant supervision when it is being towed. 2. Anchoring and mooring lines should be secured through the bow "d"- ring...
Page 14: Repair Procedure
14 important : waxes or cleaners containing alcohol should not be used on the boat fabric. Alcohol will prematurely dry out the boat fabric. 4. To avoid damaging the boat during storage, do not place heavy objects on it. Use in higher altitudes 1. Normal full inflation pressure is 0.25 bar for the t...
Page 15
15 workmanship, but only when the sale has been made in a country to which distribution is authorised by us. Ii. This warranty applies only to defects in material and workmanship, it does not apply to normal wear and tear, or to damage caused by: 1) neglect, lack of maintenance, accident, abnormal o...
Page 16
16 ec declaration of conformity according to ec directive “recreational craft” 94/25/ec i, the undersigned : qingdao shinkwang boat co., ltd. Songshuzhuang village xifu town chengyang district qingdao, china certify that the boat is made following norms 94/25/ec with category design c authorized rep...
Page 17
17 on behalf of the producer: - name : mr. Cho ki sung - date : 27 th april, 2007 - function : producing director - signature : enter here your hin c n - s k i please sign hereunder for receipt of this manual and all the relevant manuals of equipment onboard. Name : signature : date :.