Talaris Nvision Quick Start Manual
TP10613010 Rev.02
Copyright © 2009 by Talaris Ltd., Basingstoke (UK)
Page 1 of 2
Talaris House, Crockford Lane, Chineham Business Park, Basingstoke, Hampshire RG24 8QZ, England.
Telephone +44 (0)1256 368000 Fax +44 (0)1256 368001 www.talaris.com
Model: Nvision
(Virtual Pocket Processing)
Quick User Guide
1. Display / Control Panel
Process Selection
Function Selection
0
Zero
Returns you to standard
note authentication.
Scroll arrow
keys
Scrolling through display
options.
1
Fitness
1
Turns fitness sorting on
or off.
User
Change operator or
password.
2
CDA
Turns authentication off.
Prog
Save, load, delete
programs.
3
BRF
1
Turns on and off the
Banknote Recycling
Framework process.
System
Configuration or Version
information.
4
Face
Facing the notes.
Batch
Batch totals.
5
Orient
Orientation of the notes.
Total
Details of count.
6
Issue
Issue splitting of the
notes.
Det
1
Switching on/off
detectors and adjusting
detector sensitivity.
7
Piece
Piece counting paper.
Clear
Clear information.
8
Currency
Selecting a currency.
Start/Stop
Manual start/stop key.
9
Denom
Selecting a
denomination.
Function keys Selecting functions from
the display.
Note: Once in the BRF process, no other processes
can be selected. You must have
BRF switched off, to run the other processes.
3. Powering up the Machine
Connect the mains lead to the socket on the rear of the machine.
Plug the machine’s power lead into a mains socket and switch on the mains supply.
Switch on the machine’s on / off switch. The machine will power up and complete a self
test routine while the Nvision logo is being displayed. This may take about 20 seconds.
At this time the lights on each stacker pocket will flash from red to green. Next select
operator or supervisor mode by using the scroll key, then enter your password (if set) or
press OK (F1) to go to the count display.
The machine will then automatically be configured to the operating settings that were
previously saved for that user.
Note: If the display comes up with a warning, check that the metal tab on the top left
hand side of the rear cover has activated the safety switch correctly See section
“2.2 Machine Overview (Rear View)” on page 4” of the Nvision User Guide.
TM
SUPERVISOR
ENTER PASSWORD : _
OK
Å
CLEAR
READY FOR NEW BATCH
BACK
2. Feed Gap Adjustment
Feed gap adjuster (Fig 3)
Moveable Plate release
latches (Fig 1)
Feed guide release clip
(Fig 2)
Pull back and rotate
Feed gap adjustment is required for the following reasons:
•
The counting of new or mint condition notes.
•
The counting thin or poor condition notes.
•
The counting of average condition notes.
The adjuster nut is graduated with numbers:
1
2
3
4
Remove the rear cover to adjust the feed gap on the machine.
Carefully press in both of the green moveable plate latches and slowly pull the assembly
back towards you (Fig 1). Care point: You should always support this assembly as you
lower it due to its weight.
Next, release the green feed guide clip and the feed guide will pivot down (Fig 2).
Now you can pull the feed gap adjuster nut towards the centre of the machine and rotate
the nut in the required direction (Fig 3). The feed gap number selected must have the
white arrow pointing towards it.
The default setting for the note feed gap is 3.
New or mint notes may require a slightly smaller gap to count than average notes (i.e. 2).
Old notes may require a slightly larger gap than average notes (i.e. 4).
The higher the setting (i.e. 4), the larger the gap.
Adjust, then re-check the feed.
4. Stacker Pocket Indicator Lights
The stacker pocket indicator lights by the
side of each stacker pocket will tell you
what type of event has happened in each
pocket.
A solid green light is for a correct and
authenticated count (stacker 1). It can
also apply to stacker 2, depending on the
process you are using.
A flashing green indicates an
authenticated count but has a note of the
wrong denominational value in that count.
(Not applicable in the BRF Process.)
A solid red light is for an un-recognisable
note or is for an invalid count.
A flashing red light indicates a note that
has failed an authentication check (stacker 2).
Note: For further information on all the different process and functions selections, see
sections 4 and 5 of the Nvision User Guide.
Note: For display messages and error codes, See section “8 Display Messages and
Error Codes” on page 65” of the Nvision User Guide.
Stacker 2
Stacker 1
This Quick User Guide explains the more frequently used features of the Nvision note sorter. However, the features available will vary depending on the machine type and the detector
packages fitted. Features that are only available on specific models will be identified with a number added to the feature name, these are explained on page 2 of this guide.
Suzo nr: 177-0700