1. DL manuals
  2. Talbsys
  3. Mixer
  4. Advanced Vortex
  5. Instruction Manual

Talbsys Advanced Vortex Instruction Manual

Summary of Advanced Vortex

  • Page 1

    Instruction manual basic vortex mixer standard vortex mixer advanced vortex mixer pulsing vortex mixer instruction manual.

  • Page 2

    W arranty manufacturer warrants this product to be free from defects in material and workmanship when used under normal conditions for five (5) years. Please complete and return the enclosed warranty card. For your reference, make a note of the serial number, date of purchase and supplier here. Seri...

  • Page 3

    Operating conditions: indoor use only. Temperature: 4 to 40°c (39.2 to 104°f) humidity: 20% to 85% relative humidity, non-condensing altitude: 0 to 6,562 ft. (2000 m) above sea level non-operating storage: temperature: -20 to 65°c (-4 to 149°f) humidity: 20% to 85% relative humidity, non-condensing ...

  • Page 4

    Please read the entire instruction manual before operating the vortex mixer. Warning! Do not use the vortex mixer in a hazardous atmosphere or with hazardous materials for which the unit was not designed. Also, the user should be aware that the protection provided by the equipment may be impaired if...

  • Page 5

    Overall dimensions (l x w x h): 8 x 5 x 5.25” (20.3 x 12.7 x 13.3cm) electrical (50/60 hz): 120v: 1.2 amps, 150 watts 230v: 0.6 amps, 150 watts speed range*: on mode: 500 to 3000rpm ** auto mode: 1000 to 3000rpm ** pulse mode: 3000rpm ** timer: 1 second to 9999 minutes (increased in 1 second increme...

  • Page 6

    D igital & p ulsing v ortex m ixer c ontrol p anel the front panel of the digital/pulsing vortex mixer contains all the switches, controls and displays needed to operate the unit. A. 3-way rocker switch: auto/standby/on rocker switch starts/stops the vortexing function. B. Time display: displays acc...

  • Page 7

    Your vortex mixer is ready for most one-handed applications. The vortex mixer operates by mixing tubes just prior to testing. O perating t ips these units are not intended for continuous use over extended periods of time. A built-in temperature sensor will prevent the unit from overheating by shutti...

  • Page 8

    1. Make sure the 3-way rocker switch is in the center, standby position. Plug the power cord into a properly grounded outlet. The unit is now on and in a standby mode. 2. For continuous operation, push the rocker switch to the right, on position. For intermittent/touch operation, push the rocker swi...

  • Page 9

    H ead /a ccessory i nstallation i nstructions installing the cup head, 3” head or other head attachments: 1. Move the 3-way rocker switch to the center, off/standby position. For the fixed speed vortex mixer disconnect the power cord from the wall outlet. 2. If using an insert retainer with tube hol...

  • Page 10

    H ead /a ccessory i nstallation i nstructions installing single tube holder: 1. Move the 3-way rocker switch to the center, off/standby position. Single tube holder should not be used on the fixed speed vortex mixer. 2. Remove cup head, or any other accessory from the vortex mixer. 3. Align the base...

  • Page 11

    Problem cause solution unit will not run mechanical obstruction or motor obstruction removeobstructionandpressdownoncupheadseveraltimestoconfirmnoobstructionexists.If problem persists, please contact your talboys representative for repair. Unit is excessively noisy sensor fan misaligned or motor mis...

  • Page 12

    A ccessories micro-tube holder - mixes (48) 0.25 to 2ml microtubes. Requires insert retainer. Description part number micro-tube holder (2 pk) 945638 insert retainer 945631 micro-well plate holder - ideal for mixing 96 well plates or deep well blocks. Requires insert retainer. Description part numbe...

  • Page 13

    A ccessories cont ’ d tube holder kit includes: (1) 9-13mm tube holder, (1) 14-19mm tube holder, (1) 20-25mm tube holder, 1 flat foam insert, 2 vessel harness, and 1 insert retainer part number 945630 3” rubber head cover & 3” head- designed for mixing irregular shaped objects. Description part numb...

  • Page 14

    201 wolf drive • po box 87 • thorofare, nj 08086 • phone: 1-888-talboys • fax: 856-686-1601 e-mail: troemner@troemner.Com • www.Troemner.Com 715027-00 (rev 6 - 8/14) manufactured by:.