1. DL manuals
  2. Talent
  3. Network Router
  4. LT804-AW
  5. User Manual

Talent LT804-AW User Manual

Manual is about: Talent LT804-AW ADSL2+ Router User Manual

Summary of LT804-AW

  • Page 1

    User manual adsl2+ router.

  • Page 2: Index

    Index 1.0 about this manual ............................................................................................................... 1 1.1 document objectives .......................................................................................................... 1 1.2 product overview .......

  • Page 3: Adsl2+ Router

    1 adsl2+ router 1.0 about this manual this manual is developed for users, system managers, network managers, and contains installation, configuration, and operation of the adsl2+ router. 1.1 document objectives the objectives of this manual are to describe all the initial hardware installation and b...

  • Page 4: Adsl2+ Router

    2 adsl2+ router 2.0 specification adsl standards supported ● compliant to itu-t g.992.1 (g.Dmt), g.992.2 (g.Lite), g.992.3 (adsl2), g.992.4 (splitterless adsl2), g.992.5 (adsl2+) for annex a, b ● g.Lite (g.992.2) with line rate support of up to 1.5mbps downstream and 512kbps upstream. ● supports mul...

  • Page 5: Adsl2+ Router

    3 adsl2+ router 2.1 led meaning your adsl2+ router has indicator lights. Please see below for an explanation of the function of each indicator light. Power indicator adsl link indicator internet active indicator ethernet active indicator table 1. Led function label color on flash off green ready not...

  • Page 6: Adsl2+ Router

    4 adsl2+ router 2.2 back panel connectors table 2 shows the function of each connector and switch of the adsl2+ router’s rear panel. Figure 1. Illustrate the connectors / figure 2. Illustrate the power switch. Table 2. Function / description of connectors connector description switch power switch, w...

  • Page 7: Adsl2+ Router

    5 adsl2+ router 3.0 hardware requirements to use adsl2+ router, please have following hardware / accessories ready. A pc with pre-installed ethernet adapter (required) 12vac power adaptor (included in the package) rj-45 ethernet cable (included in the package) rj-11cable (included in the package) 3....

  • Page 8: Adsl2+ Router

    6 adsl2+ router 4.0 installation & setup follow each step carefully and only go to the next step once you have completed the previous step. Connection of adsl2+ router if you have an isdn telephone line connect the router as shown below: 1. Connect the supplied rj45 ethernet cable from your pc's eth...

  • Page 9: Adsl2+ Router

    7 adsl2+ router if you have a pstn telephone line (normal analog line) connect the router as shown below: 1. Connect the supplied rj45 ethernet cable from your pc's ethernet port to adsl2+ router's “lan” port. 2. Connect the supplied rj11 telephone cable from your home's telephone jack to the “line”...

  • Page 10: Adsl2+ Router

    8 adsl2+ router 5.0 configuration procedures before starting the adsl2+ router configuration, please kindly configure the pc computer as below, to have automatic ip address / dns server. For windows 98se / me / 2000 / xp 1. Click on “start” -> “control panel” (in classic view). In the control panel,...

  • Page 11: Adsl2+ Router

    9 adsl2+ router 3. Double click on "internet protocol (tcp/ ip)". 4. Check "obtain an ip address automatically" and “obtain dns server address automatically” then click on "ok" to continue. 5. Click "show icon in notification area when connected" (see screen image in 3. Above) then click on "ok" to ...

  • Page 12: Adsl2+ Router

    10 adsl2+ router for windows vista-32/64 1. Click on “start” -> “control panel” -> “view network status and tasks”. 2. In the manage network connections, click on “manage network connections” to continue..

  • Page 13: Adsl2+ Router

    11 adsl2+ router 3. Single right click on “local area connection", then click "properties". 4. The screen will display the information “user account control” and click “continue” to continue. 5. Double click on "internet protocol version 4 (tcp/ipv4)"..

  • Page 14: Adsl2+ Router

    12 adsl2+ router 6. Check "obtain an ip address automatically" and “obtain dns server address automatically” then click on "ok" to continue..

  • Page 15: Adsl2+ Router

    13 adsl2+ router for windows 7-32/64 1. Click on “start” -> “control panel” (in category view) -> “view network status and tasks”. 2. In the control panel home, click on “change adapter settings” to continue..

  • Page 16: Adsl2+ Router

    14 adsl2+ router 3. Single right click on “local area connection", then click "properties". 4. Double click on "internet protocol version 4 (tcp/ipv4)"..

  • Page 17: Adsl2+ Router

    15 adsl2+ router 5. Check "obtain an ip address automatically" and “obtain dns server address automatically” then click on "ok" to continue..

  • Page 18: Adsl2+ Router

    16 adsl2+ router 6.0 adsl2+ router configuration 1. Please insert the supplied cd into your cd-rom drive. 2. The cd should auto-start, displaying as below. Please click “run autorun.Exe” to continue. If your cd does not start automatically go to windows explorer, select your cd drive and click “auto...

  • Page 19: Adsl2+ Router

    17 adsl2+ router 4. Enter the vpi, vci, username and password your isp (internet services provider) provided, and protocol mode. 5. Please click “setup” button, when the procedure is completed, it will start to configure the device for a while. 6. Now, checking adsl 2+ router hardware connection, ad...

  • Page 20: Adsl2+ Router

    18 adsl2+ router 7. Easy setup configuration completed. The connection to the internet service is ready to use. Click on " exit " to exit this program..

  • Page 21: Adsl2+ Router

    19 adsl2+ router 8. Click on " exit " to exit this program. 9. Now, the adsl2+ router has been configured completed, and suitable for internet connections..

  • Page 22: Adsl2+ Router

    20 adsl2+ router 7.0 technology glossary 10base-t an adaptation of the ethernet standard for local area network (lan). 10base-t uses a twisted pair cable with maximum length of 100 meters. Aal atm adaptation layer that defines the rules governing segmentation and reassembly of data into cells. Diffe...

  • Page 23: Adsl2+ Router

    21 adsl2+ router ftp file transfer protocol. The internet protocol (and program) used to transfer files between hosts. Ipoa (rfc 1577) classical ip and arp over atm. Considers atm configured as a logic ip sub-network(lis) to replace ethernet local lan segments. Isp internet service provider. A compa...

  • Page 24: Adsl2+ Router

    22 adsl2+ router are written up as rfcs rfc 1483 multi-protocol encapsulation over aal-5. Two encapsulation methods for carrying network interconnect traffic over atm aal-5. The first method allows multiplexing of multiple protocols over a single atm virtual circuit. The protocol of a carried pdu is...

  • Page 25: Adsl2+ Router

    23 adsl2+ router 8.0 introduction of the web configuration 8.1 web configuration overview the embedded web configuration allows you to manage adsl2+ router from anywhere through a browser such as microsoft internet explorer or netscape navigator. Use internet explorer 6.0 and later or netscape navig...

  • Page 26: Adsl2+ Router

    24 adsl2+ router quick start guide you can use "quick start" to setup the router as follows, and the router will connect to the internet via adsl line. Click "quick start" to get into the quick setup procedures. Click "run wizard" to start up this procedure..

  • Page 27: Adsl2+ Router

    25 adsl2+ router step 1 – please click "next" to setup your new administrator's password. Step 2 – please click "next" to setup your time zone..

  • Page 28: Adsl2+ Router

    26 adsl2+ router step 3 – please click "next" to setup your internet connection type. You can have this information from your internet service provider. Step 4 - enter the connection information provided by your isp and click “next “..

  • Page 29: Adsl2+ Router

    27 adsl2+ router step 5 - enter the connection information provided by your isp and click “next “. Step 6 – please click “close “ to finish quick start..

  • Page 30: Adsl2+ Router

    28 adsl2+ router system time go to maintenance->time zone and select system time as you wish. Connecting to a simple network time protocol (sntp) server allows the router to synchronize the system clock to the global internet. The synchronized clock in the router is used to recorded the security log...

  • Page 31: Adsl2+ Router

    29 adsl2+ router firmware update go to maintenance -> firmware to upgrade the firmware. The new firmware for your router can improve functionality and performance. Enter the path and name of the upgrade file then click the upgrade button below. You will be prompted to confirm the upgrade..

  • Page 32: Adsl2+ Router

    30 adsl2+ router system log go to status -> system log and you can see the system log file. Click “save log” to save system log file. System reset go to maintenance -> sysrestart to restart your system. In the event that the router stops responding correctly or in some way stops functioning, you can...

  • Page 33: Adsl2+ Router

    31 adsl2+ router adsl status go to status->device info. The 'adsl line status' enables you to check the status of your adsl connection including how fast data is being transferred..

  • Page 34: Adsl2+ Router

    32 adsl2+ router adsl statistics go to status-> statistics and select adsl interface. You can see the traffic statistics of adsl interface. Vc configuration go to interface setup -> internet. To add or delete adsl vc configuration, these information provide by isp..

  • Page 35: Adsl2+ Router

    33 adsl2+ router wan configuration go to interface setup -> internet. The router can be connected to your service provider in any of the following ways. Dynamic ip address: obtain an ip address automatically from your service provider. Static ip address: uses a static ip address. Your service provid...

  • Page 36: Adsl2+ Router

    34 adsl2+ router wan status go to status -> device info and select the virtual circuit to see the connection status..

  • Page 37: Adsl2+ Router

    35 adsl2+ router dns go to interface -> lan to enable dhcp server. Then you can set dns server for the router. A domain name system (dns) server is like an index of ip addresses and web addresses. If you type a web address into you browser, a dns server will find that name in its index and find the ...

  • Page 38: Adsl2+ Router

    36 adsl2+ router ddns go to access management -> ddns to setup your ddns parameters. Dynamic dns allows you to update your dynamic ip address with one or many dynamic dns services. So anyone can access your ftp or web service on your computer using dns-like address..

  • Page 39: Adsl2+ Router

    37 adsl2+ router cwmp item name description cwmp enable or disable tr069 function url type acs server’s url user name type acs server login username password type acs server login password path type the path for connection request port type the port for connection request username type username for ...

  • Page 40: Adsl2+ Router

    38 adsl2+ router lan configuration go to interface setup -> lan. The 'lan settings' option enables you to configure the lan port. If the dhcp relay is selected, the dhcp requests from local pcs are forward to the dhcp server runs on wan side. To have this function working properly, disable the nat t...

  • Page 41: Adsl2+ Router

    39 adsl2+ router ip filtering go to access management -> ip filtering to block some packets form wan.The router provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. The user can set dif...

  • Page 42: Adsl2+ Router

    40 adsl2+ router acl setting go to access management -> acl to enable remote management. The user may remotely access the adsl router once setting his ip as a secure ip address through selected applications. With the default ip 0.0.0.0, any client would be allowed to remotely access the adsl router....

  • Page 43: Adsl2+ Router

    41 adsl2+ router virtual server go to advanced setup ->nat -> virtual server to set virtual server as you need.(known as port mapping).You can configure the router as a virtual server so that remote users accessing services such as the web or ftp at your local site via public ip addresses can be aut...

  • Page 44: Adsl2+ Router

    42 adsl2+ router dmz setting go to advanced setup ->nat -> dmz to set dmz parameters. If you have a local client pc that cannot run an internet application properly from behind the nat firewall, you can open the client up to unrestricted two-way internet access by defining a virtual dmz host. Static...

  • Page 45: Adsl2+ Router

    43 adsl2+ router dynamic routing go to interface setup -> internet to select dynamic route as you need. The dynamic routing feature of the router can be used to allow the router to automatically adjust to physical changes in the network's layout. The router uses the dynamic rip protocol. It determin...

  • Page 46: Adsl2+ Router

    44 adsl2+ router routing table go to advanced setup -> routing to see the routing table.The routing table allows you to see how many routings on your routing table and interface information system status go to status -> device info to see the router's information. The system status page shows the wa...

  • Page 47: Adsl2+ Router

    45 adsl2+ router snmp go to access management -> snmp to setup snmp feature.Simple network management protocol is used for exchanging information between network device. Get community : select to set the password for the incoming get- and getnext requests from the management station. Set community :...

  • Page 48: Adsl2+ Router

    46 adsl2+ router qos setting go to advanced setup -> qos to setup qos features. This option will provide better service of selected network traffic over various technologies..

  • Page 49: Adsl2+ Router

    47 adsl2+ router vlan go to advanced setup -> vlan to enable vlan features. Virtual lan (vlan) is a group of devices on one or more lans that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different lan segments. Be...

  • Page 50: Adsl2+ Router

    48 adsl2+ router vlan group go to advanced setup -> vlan-> define vlan group to setup vlan group features. Firewall go to advanced setup ->firewall to setup firewall features. Select this option can automatically detect and block denial of service (dos) attacks, such as ping of death, syn flood, por...

  • Page 51: Adsl2+ Router

    49 adsl2+ router 9.0 universal plug-and-play (upnp) 9.1 universal plug and play overview universal plug and play (upnp) is a distributed, open networking standard that uses tcp/ip for simple peer-to-peer network connectivity between devices. An upnp device can dynamically join a network, obtain an i...

  • Page 52: Adsl2+ Router

    50 adsl2+ router 9.5 configuring upnp from the site map in the main menu, click upnp under access managemen to display the screen shown next. The following table describes the labels in this screen. Label description upnp select this checkbox to activate upnp. Be aware that anyone could use a upnp a...

  • Page 53: Adsl2+ Router

    51 adsl2+ router 9.6 installing upnp in windows example this section shows how to install upnp in windows me and windows xp. 9.7 installing upnp in windows me follow the steps below to install the upnp in windows me. Step 1. Click start and control panel. Double-click add/remove programs. Step 2. Cl...

  • Page 54: Adsl2+ Router

    52 adsl2+ router 9.8 installing upnp in windows xp follow the steps below to install the upnp in windows xp. Step 1. Click start and control panel. Step 2. Double-click network connections. Step 3. In the network connections window, click advanced in the main menu and select optional networking comp...

  • Page 55: Adsl2+ Router

    53 adsl2+ router step 5. In the networking services window, select the universal plug and play check box. Step 6. Click ok to go back to the windows optional networking component wizard window and click next..

  • Page 56: Adsl2+ Router

    54 adsl2+ router 9.9 using upnp in windows xp example this section shows you how to use the upnp feature in windows xp. You must already have upnp installed in windows xp and upnp activated on adsl2+ router. Make sure the computer is connected to a lan port of adsl2+ router. Turn on your computer an...

  • Page 57: Adsl2+ Router

    55 adsl2+ router step 4. You may edit or delete the port mappings or click add to manually add port mappings. Step 5. Select show icon in notification area when connected option and click ok. An icon displays in the system tray step 6. Double-click on the icon to display your current internet connec...

  • Page 58: Adsl2+ Router

    56 adsl2+ router 10.0 web configuration easy access with upnp, you can access the web-based configuration on adsl2+ router without finding out the ip address of adsl2+ router first. This comes helpful if you do not know the ip address of adsl2+ router. Follow the steps below to access the web config...

  • Page 59: Adsl2+ Router

    57 adsl2+ router step 4.An icon with the description for each upnp-enabled device displays under local network. Step 5. Right-click on the icon for youradsl2+ router and select invoke. The web configuration login screen displays..

  • Page 60: Adsl2+ Router

    58 adsl2+ router step 6. Right-click on the icon for youradsl2+ router and select properties. A properties window displays with basic information about adsl2+ router..

  • Page 61: Adsl2+ Router

    59 adsl2+ router 11.0 troubleshooting a.1 using leds to diagnose problems the leds are useful aides for finding possible problem causes. A.1.1 power led the pwr led on the front panel does not light up. Steps corrective action 1 make sure that adsl2+ router’s power adaptor is connected to adsl2+ rou...

  • Page 62: Adsl2+ Router

    60 adsl2+ router a.2 telnet i cannot telnet into adsl2+ router. Steps corrective action 1 check the lan port and the other ethernet connections. 2 make sure you are using the correct ip address of adsl2+ router. Check the ip address of adsl2+ router. 3 ping adsl2+ router from your computer. If you c...

  • Page 63: Adsl2+ Router

    61 adsl2+ router a.4 login username and password i forgot my login username and/or password. Steps corrective action 1 if you have changed the password and have now forgotten it, you will need to upload the default configuration file. This will erase all custom configurations and restore all of the ...

  • Page 64: Adsl2+ Router

    62 adsl2+ router 2 the username and password apply to pppoe and ppoa encapsulation only. Make sure that you have entered the correct service type, user name and password (be sure to use the correct casing). A.7 internet access i cannot access the internet. Steps corrective action 1 make sure adsl2+ ...