Talon AB3206 User Manual - page 2
19
18
GB
1. THROTTLE TRIGGER
2. THROTTLE LOCK
3. ON/OFF IGNITION SWITCH
4. TOP ASSIST HANDLE
5. SPARK PLUG WIRE / SPARK
PLUG
6. CHOKE LEVER
7. STARTER HANDLE
8. AIR CLEANER COVER
9. FUEL CAP
10. FUEL TANK
11. PRIMER BULB
12. HARNESS
13. CONTROL HANDLE
14. OPERATING TUBE
15. HOSE CLAMP
16. FLEX TUBE
17. THROTTLE LINKAGE
18. MUFFLER COVER
19. SPARK ARRESTER SCREEN
20. VENTED BACK PAD
21. INTERMEDIATE TUBE
22. 56mm NOZZLE
23. 45mm CONCENTRATOR
NOZZLE
24. THROTTLE LINKAGE CLIPS
GENERAL IDENTIFICATION
SPECIFICATIONS
21
22
23
1
2
3
4
5
6
7
8
9
10
11
12
18
17
16
15
14
13
24
19
20
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-cooled, 2 Cycle
Engine displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 cm
3
(1.83 ci)
Engine Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,200 min
-1
Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,400-4,400 min
-1
Air Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 km/h
Air Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.11 m
3
/min
Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 in (0.635 mm)
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.5 oz (550 ml)
Dry Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 kg
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 dB(A)
Sound pressure level at ear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 dB(A)
Guarantee sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 dB(A)
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.17m/s
2
EN ISO 22868 : 2005.
GB
• ATTACH FLEX TUBE
Put the hose clamp(C) on the flex tube before connecting
the flex tube and the fan’s outlet tube together.
Connect the flex tube (B) to the fan’s outlet tube (A) (Fig.
1) with a hose clamp (C) (Fig. 2) and tighten securely (Fig.
2).
• ATTACH OPERATING TUBE
NOTE: keep the throttle cable as straight as possible
when connecting the blower tubes.
1. Place the unit on flat surface during assembly.
Insure screw mechanism of clamp is positioned
away from operator.
2. Put the hose clamp (C) on the flex tube and the
operating tube together.
3. Turn the rotary ring mark (D) so it aligns with the
throttle handle (F). Insert the operating tube (E) into
the flex tube (B) (Fig. 3) and then tighten securely
with a hose clamp (G) (Fig. 4).
4. Attached throttle linkage clips (# 24-know your
blower) - to both ends of the flex tube to secure the
throttle cable. ( See Fig. 5 and Fig. 6)
• ATTACH INTERMEDIATE TUBE AND
CONCENRATOR NOZZLE
Connect the intermediate tube (H) and air nozzle (I).
Push the tubes together and turn them clockwise so that
they lock together. (Fig. 7)
• ADJUST BACK PACK AND HARNESS AND
CONTROL HANDLE
1. Place blower on your
back by slipping arms
through the shoulder
straps as if you were
putting on a jacket (Fig.
8).
2. Once
adjustments
have been made, to
the straps for user
comfort, remove the
blower from your back and place on level ground in
an upright position.
3. Adjust backpack harness and control handle.
• FUEL
Use regular grade unleaded gasoline mixed with Talon
40:1 custom 2-cycle engine oil for best results. Use mixing
ratios in Section FUEL MIXING TABLE.
• MIXING FUEL
Add oil to an approved fuel container followed by the
gasoline to allow incoming gasoline to mix with oil. Shake
container to ensure thorough mix.
• FUEL AND LUBRICATION SYMBOLS
ASSEMBLY INSTRUCTIONS
Fig. 1
A
Fig. 2
Fig. 3
B
Fig. 4
Fig. 8
WARNING:
Never use straight gasoline in your
unit. This will cause permanent engine damage and
void the manufacturer’s warranty for that product.
Never use a fuel mixture that has been stored for over
90 days.
WARNING:
If 2-cycle lubricant other than Talon
Custom Lubricant is to be used, it must be a premi-
um grade oil for 2-cycle air cooled engines mixed at
a 40:1 ratio. Do not use any 2-cycle oil product with
a recommended mixing ratio of 100:1. If insufficient
lubrication is the cause of engine damage, it voids
the manufacturer’s engine warranty.
WARNING:
Lack of lubrication voids engine
warranty. Gasoline and oil must be mixed at 40:1.
Gasoline and oil
mix 40:1
B
C
180˚
D
F
E
G
Fig. 5
Fig. 6
THROTTLE LINKAGE CLIPS
THROTTLE LINKAGE
CLIPS
Fig. 7
B
D
H
I
45mm
56mm
FUEL AND LUBRICATION