Talon Pro 18V d.c. Cordless Impact Wrench User Manual - page 3
Fig. 5
Trigger
A
B
C
E
D
F
• TRIGGER
When the trigger is depressed the
chuck will rotate (provided the for-
ward/reverse switch is set in the
forward or reverse position). The
trigger can be locked in the OFF
position.l This helps reduce the possibility of accidental start-
ing when not in use. To lock trigger, place selection lever in the
cente position.
• ALLING AND REMOVING THE SOCKETS
OR ACCESSORIES ( FIG. 6)
NOTE : Always be sure that the
tools is switched off and the bat-
tery pack is removed before
installing or removing the sock-
ets.
•
To install a socket on the
anvil, align the hole of the
socket with, push firmly.
•
To remove a socket from the anvil, pull the socket out
firmly.
4
WARNING: Be prepared for binding or
break
-
through. When these situations occur,
the
impact
wrench
has a tendency to grab and kick in
the
opposite direction, and could cause loss
of control.
If you are not prepared, this loss of
control can result in possible serious injury.
WARNING: Always wear safety goggles or
safety glasses with side shields when
operating tool. Failure to do so could result in
objects being thrown into your eyes, resulting
in possible serious injury.
WARNING: Read all instructions Failure to
follow all instructions listed below may result
in electric shock, fire and/or serious injury.
The term "power tool" in all of the warnings
listed below refers to your mains-operated
(corded) power tool or battery-operated
(cordless) power tool.
3
SPECIFICATIONS
This product contains
Ni-MH, Ni-Cd and Lithium
batteries
which must
be disposed of properly.
1. Be aware that this tool is always in an operating condi-
tion, because it does not have to be plugged into an
electrical outlet.
2. Fully charge the battery for better operation.
3. Be sure the battery is snapped in place.
4. When not in use, lock the switch.
5. When operating at a high place, be aware of things
below and around you.
l
•
BATTERY CHARGING
To charge the battery pack it must
first
be removed from the
impact wrench.
To
remove the battery pack, grasp
both sides of the battery pack and
depress that battery clips as
shown if Fig 1. Now gently pull
the battery pack from the hous-
ing.
•
FORWARD/REVERSE SWITCH (FIG. 2 & FIG. 3)
1.
The tool starts and stops by depressing and releas-
ing the switch.
2.
To alter the direction of rotation, first stop the tool by
releasing the switch and allow the tool to stop.
3.
Then push the forward/ reverse level to the right or
left. Depress the level from the “ “ side for clock-
wise rotation or from the “
“ side for counter clock-
wise rotation.
4.
Before operation ensure the forward/reverse switch is
set for the desired direction of rotation. Do not
change direction for rotation until the tool comes to a
complete stop. Keep the forward/reverse switch in
the neutral position when the tool is not in use.
•
FORWARD REVERSE SWITCH
This switch determines the direc
tion
of rotation of the chuck, ie.
clockwise or
counter
clockwise.
To alter the direction of rotation
stop the
impact wrench
then push the
selec
tion lever to the left of right. When
the lever is in the “F” (Forward)
position the chuck will rotate clockwise. When the lever is
in the “R” (Reverse) position the chuck will rotate anticlock
wise. Before operation check that the switch is set in the
required position.
PRECAUTIONS ON USING YOUR CORD-
LESS TOOL
OPERATION
WARNING: Before attempting to use any tool,
make sure your are familiar with all operating fea-
tures and safety requirements.
A
Trigger
B
Forward/Reverse
Switch
C
Anvil
D
Battery Clip
E
Battery Pack
F
Charger
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TD7910
Square Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13mm
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Vd.c
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1900 min
-1
Maximum Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .385 Nm
Impacts Per Minute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2500 B.P.M
Bettery Model No.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B186 (3.0 Ah)Lithium,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B187 (1.3 Ah)Ni-Cd, B187 (2.5 Ah)Ni-MH
Charger Model No.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C186
Variable Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Y
Soft grip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Y
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5 kg
Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 dB (A)
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 dB (A)
Vibrations Level Max. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <16,5 m/s2
Fig. 2
Fig. 3
GB
GB
Fig. 1
Fig. 6
Sockets
Anvil
Fig. 4
F/R
Rückwärtsschalter