Talon Tools AB3201 User Manual - page 2
3
2
GB
GB
1. HANDLE
2. THROTTLE TRIGGER
3. “OFF” SWITCH
4. MUFFLER / SPARK ARRESTER
SCREEN
5. MUFFLER COVER
6. FUEL TANK
7. STARTER HANDLE
8. CARBURETOR
9. FUEL CAP
10. AIR FILTER COVER
11. CHOKE LEVER
12. INLET COVER
13. BLOWER TUBES
14. SPARK PLUG WIRE / SPARK
PLUG
15. VACUUM TUBES
16. VACUUM BAG
17. SIDE HANDLE
18. THROTTLE LOCK
19. PRIMER BULB
20. HARNESS
21. VACUUM BAG TUBE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
20
18
19
21
GENERAL IDENTIFICATION
SPECIFICATIONS
Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Air-cooled, 2 Cycle,Chrome Cylinder
Engine displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 cc (2.0ci)
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7,500/min
-1
Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3,000-3,500/min
-1
Air Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .264 km/h
Air Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10.64 cu. m/min.
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 oz. (710 ml)
Dry Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.1 kg
Sound Power Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 dB
21
• BLOWER ATTACHMENT ASSEMBLY INSTRUC-
TIONS
1. Twist blower nozzle (A) clockwise into the straight
blower tube (B) until tight (Fig. 1A).
2. Insert the straight blower tube (B) into the blower hous-
ing (C). Align tabs (D) on tube with grooves (E) in the
housing (Fig. 1B).
3. Push tube into ridge (F) and twist counterclockwise 3/8
of a turn to lock into position (Fig. 1C).
4. Lock screw (G) for blower tube (Fig. 1D)
• HARNESS INSTALLATION
Attach the 2 harness clips to the 2 links in the blower han-
dle (Fig. 2).
• VACUUM ATTACHMENT ASSEMBLY INSTRUC-
TIONS
Remove blower attachments.
To install vacuum bag:
1. Insert vacuum bag tube (A) into blower housing (B).
Align tabs (D) on tube with grooves (E) in housing (Fig.
3A).
2. Push tube in to ridge (F) and twist counterclockwise 3/8
of a turn to lock into position (Fig. 3B).
3. Lock screw (G) for vacuum bag tube. (Fig. 1D)
4. Slide bag (G) over flared end of tube (H). Fold under
excess. Insert strap (J) through loop and draw tight and
lock strap in place (Fig. 3C).
To install vacuum (suction) tube:
1. Connect the 2 vacuum tubes. Align as shown (Figure
3D).
2. Remove cover screw (K) (Fig. 3E).
3. Hold inlet cover open. Insert tube aligning tabs (L) and
notches (M). Turn clockwise to lock tube into position
(Fig. 3F).
4. Install cover screw (K) through tube tab and into hous-
ing. Tighten screw (Fig. 3G).
• SIDE HANDLE
Slide handle (A) into the groove in the housing (B). Secure
with the two screws (C) (Fig. 4).
• INSTALLATION OF SPARK ARRESTER
A spark arrester screen may be required when using your
unit. Check your local state requirements.
1. Remove the 2 small muffler screws (A) (Fig. 5A).
2. Grasp cover (B) and screen (C), and insert first screw
(D) (Fig. 5B).
3. Install onto muffler and secure first screw.
4. Install and secure second screw (Fig. 5C).
NOTE: Do not overtighten screws.
ASSEMBLY INSTRUCTIONS
A
Fig. 1A
Fig. 1C
F
C
B
D
E
Fig. 1B
B
Fig. 1D
G
Fig. 2
Fig. 3A
A
B
D
E
F
Fig. 3B
B
C
A
Fig. 4
Fig. 3D
G
K
H
J
M
K
L
Fig. 3C
Fig. 3E
Fig. 3F
Fig. 3G