Summary of ITR-CS15D
Page 1
User’s manual itr-cs15d.
Page 2: Itr-Cs15D
Itr-cs15d copyrights i copyrights ©2012 talos integrated technolgies. All rights reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. This documen...
Page 3: Itr-Cs15D
Itr-cs15d contents ii contents copyrights .................................................................................................I liability disclaimer ...................................................................................I regulatory information..................................
Page 4: Itr-Cs15D
Itr-cs15d contents iii 4.2. Serial port com1/3..................................................................................... 35 4.3. Com 2 (10-pin rj50) .................................................................................. 35 4.4. Cash drawer ........................................
Page 5: Itr-Cs15D
Itr-cs15d chapter 1 4 1. 1. Hardware setup 1.1. Packing contents 1. Itr-cs15d x 1 4. Rj50 to db9 com port adapter cable x 1 2. Power adapter x 1 5. Io/cable cover x 1 3. Power cord x 1 6. Drive and utility dvd x 1.
Page 6: Itr-Cs15D
Itr-cs15d chapter 1 5 1.2. Quick tour front view and side view a. The led indicator will glow green when power is on. The led indicator will blink red when the hdd is accessed. A. Customer display mounting hole cover d. Power switch b. Hdd tray e. I/o cover c. Msr cover.
Page 7: Itr-Cs15D
Itr-cs15d chapter 1 6 back panel i/o a. Dc in g. Cd/dio (for cash drawer) b. Com 2 (10-pin rj -50) * h. Cf card slot c. Usb 1/2 i. Usb 3/4 d. Lan 1 j. Com3 e. Lan 2 k. Vga f. Com1 caution * note: please use 10-pin rj50 connector, 8-pin rj45 is incompatible. 1.3. Hdd replacement 1. Loosen and remove ...
Page 8: Itr-Cs15D
Itr-cs15d chapter 1 7 3. Disconnect the sata cable connector and the sata power cable connector. 4. Loosen and remove the four screws fixing the hdd, and then remove the hdd from the hdd tray. 5. Install the new hdd onto the device in reverse order..
Page 9: Itr-Cs15D
Itr-cs15d chapter 1 8 1.4. Basic peripherals installation 1. Remove the io panel cover from the device. 2. All cables and wires from peripherals to the pos device are recommended to be fed through the base in the direction as shown below. Warning before the cable cover is removed, please make sure t...
Page 10: Itr-Cs15D
Itr-cs15d chapter 1 9 usb mouse, usb keyboard and usb odd connect your usb mouse, usb keyboard usb odd or other usb devices to usb 1/2 or ubs 3/4 ports on the back panel of the device. Lan cable connect one end of rj-45 lan cable to the lan 1 or lan 2 port on the back panel of the device, another en...
Page 11: Itr-Cs15D
Itr-cs15d chapter 1 10 3. Install the io panel cove. Customer display a. Hardware installation 1. Remove the two screws and the vfd mounting hole cover from the device, and then pull out the connector from the device. 2. Adjust the hinge of the vfd, and then connect to the device as shown below..
Page 12: Itr-Cs15D
Itr-cs15d chapter 1 11 3. Mount the vfd to the device and tighten the two m3 screws as shown below. 5. Finished. B. Power supply configuration 1. Power up the itr-cs15d and hit the del key to enter the bios. When the bios screen appears use the or key on your external computer keyboard to select adv...
Page 13: Itr-Cs15D
Itr-cs15d chapter 1 12 2. The screen below will appear. Use the or key to scroll the screen and highlight the com6 ri/12v/15v, and then press the enter key. 3. Highlight 12v , and then press the enter key..
Page 14: Itr-Cs15D
Itr-cs15d chapter 1 13 4. Press the esc key to return to the bios setup utility screen of step 1, use the or key on your external computer keyboard to select the exit . Use the or key to highlight save changes and exit . 5. Press the enter key, use the or key to highlight the [ok] , press the enter ...
Page 15: Itr-Cs15D
Itr-cs15d chapter 1 14 msr 1. Remove the two screws fixing the msr cover. 2. Remove the msr cover from the device. 3. Connect the connectors of the msr assembly to the device..
Page 16: Itr-Cs15D
Itr-cs15d chapter 1 15 4. Tighten the two m3 screws to fix the msr assembly as shown below. 5. Finished. 1.5. Adjust angle 1.6. Turn on the device 1. Make sure all peripherals and cables are connected properly. 2. Press and hold the power switch until the power indicator on the front panel glows gre...
Page 17: Itr-Cs15D
Itr-cs15d chapter 2 16 2. 2. Basic driver installation 2.1. Before the installation 1. Connect an external usb cdrom to the usb power and insert the driver cd and turn on the device. The program autoruns and displays the talos integrated technologies main screen. 2.2. Chipset software installation 1...
Page 18: Itr-Cs15D
Itr-cs15d chapter 2 17 4. Click next . 5. Click finish . 2.3. Vga driver installation 1. On the main screen, click vga driver . 2. Click the operation system according to your application. 3. Click next . 4. Read the license agreement carefully and click yes ..
Page 19: Itr-Cs15D
Itr-cs15d chapter 2 18 5. Click next . 6. Click next . 7. Select restart your computer right now or later, and then lick finish . 2.4. Touch screen driver and software utility installation 1. On the main screen, click touch panel driver . 2. Click the operation system according to your application..
Page 20: Itr-Cs15D
Itr-cs15d chapter 2 19 3. The procedure starts. 4. Click next . 5. Check the install ps/2 interface driver box and click next . 6. Select an item according to your needs, and then click next . 7. Click ok . 8. If you want to use multi-monitor, check the box and click next . 9. Click next ..
Page 21: Itr-Cs15D
Itr-cs15d chapter 2 20 10. Click next . 11. The driver starts to install. 11. Click ok . 2.5. Lan driver installation 1. On the main screen, click via 6130 lan drive . 2. Click the operation system according to your application..
Page 22: Itr-Cs15D
Itr-cs15d chapter 2 21 3. The driver will be installed automatically. 4. Click ok on the pop-up message box. 2.6. Audio driver installation 1. On the main screen, click hd audio driver . 2. The driver is preparing to install. 3. Click next . 4. Select “ i agree ” and click next ..
Page 23: Itr-Cs15D
Itr-cs15d chapter 2 22 5. Check “ via hd audio codec drive v7.300 30.090715 ” box, and then click next . 6. Click next . 7. Click next . 8. Select restart your computer right now or later, and then lick finish ..
Page 24: Itr-Cs15D
Itr-cs15d chapter 3 23 3. 3. Touchscreen control panel quick guide 3.1. Launch touchkit utility there are two alternatives to launch touchkit . Option 1: under microsoft windows xp, click “ start ” menu and select “ programs ”, under ” touchkit ” menu, click “ configure utility ”. Option 2: click ic...
Page 25: Itr-Cs15D
Itr-cs15d chapter 3 24 3.2. General the general tab in touchkit utility shows all of touchkit touchscreen controllers installed as below, including rs232, usb and ps2 interfaces. Add the function button is used for serial rs232 controllers only. Press this button to search the touchkit serial contro...
Page 26: Itr-Cs15D
Itr-cs15d chapter 3 25 installed, this utility assumes the ps2 touchscreen controller exists and is always shown in the controller list window. Remove this function button is used for serial rs232 controllers only. This button will be grayed and disabled automatically when the selected controller in...
Page 27: Itr-Cs15D
Itr-cs15d chapter 3 26 beep beep on touch check this check box to enable driver to generate a beep sound when touch touchscreen state is switched from untouched to touched state. Beep on release check this check box to enable driver to generate a beep sound when touchscreen state is switched from to...
Page 28: Itr-Cs15D
Itr-cs15d chapter 3 27 double click area double click area is used to set the double click area. Change this value will affects the double click behavior for all of the mouse devices connected to the device. Two continuous clicks with this specified area in the specified double click time will be re...
Page 29: Itr-Cs15D
Itr-cs15d chapter 3 28 with this mode, the driver behaves similar as click on release mode. The cursor does not move to the touch position except the lift-off point. Option you can set configuration for some advanced functions with this option button. Press this button, a pop up property sheet windo...
Page 30: Itr-Cs15D
Itr-cs15d chapter 3 29 4 points calibration, clear and calibration, and linearization button click the one of three these buttons and follow the instruction on the screen to do the screen calibration. Draw test after clicking this button, you can do the drawing test by drawing any path on the screen...
Page 31: Itr-Cs15D
Itr-cs15d chapter 3 30 3.5. Display touchkit driver utility supports multiple monitor and display system. To work with multiple monitor system, you need to do proper configuration to map the touchscreen working area to the correct system display area. You can do such configuration with this property...
Page 32: Itr-Cs15D
Itr-cs15d chapter 3 31 map to main monitor when the system has only one monitor when the multiple monitor function was enabled, and the system has only one monitor. Driver allows user to generate the mouse event for the primary monitor or not when the touchscreen which were not mapped to primary mon...
Page 33: Itr-Cs15D
Itr-cs15d chapter 3 32 other operation mode quarter 1 the touchscreen will be mapped to the first quarter area of the specified monitor display. Quarter 2 the touchscreen will be mapped to the 2nd quarter area of the specified monitor display. Quarter 3 the touchscreen will be mapped to the 3rd quar...
Page 34: Itr-Cs15D
Itr-cs15d chapter 3 33 in some cases, if it is difficult to touch items at the edges of the touch panel, you can set adjustment to reach the edges of the screen image. Top if you set the edge to "smaller", touchkit will reduce the horizontal position of the top edge. If you set the edge to "larger",...
Page 35: Itr-Cs15D
Itr-cs15d chapter 3 34 x axis to right. Offset y axis if you set the offset y axis to smaller, cursor will be moved a pixel of y axis to top. If you set the offset y axis to larger, cursor will be moved a pixel of x axis to bottom. Edge compensation switch you can check support edge compensation che...
Page 36: Itr-Cs15D
Itr-cs15d chapter 4 35 4. 4. I/o definition please refer the detailed technical information about all i/o ports as followings. 4.1. Power connector pin description pin description 1 +19v 3 ground 2 +19v 4 ground 4.2. Serial port com1/3 pin description pin description 1 dcd 6 dsr 2 rxd 7 rts 3 txd 8 ...
Page 37: Itr-Cs15D
Itr-cs15d chapter 5 36 4.4. Cash drawer connector pin description pin description 1 gnd 4 p24v 2 d_out0 5 d_out1 3 d_in 6 gnd cash drawer control status address value open 280h bit 4 = 0 close 280h bit 4 = 1 read status 281h bit 0 = 0/1.
Page 38: Itr-Cs15D
Itr-cs15d chapter 5 37 5. 5 specification.
Page 39: Itr-Cs15D
Itr-cs15d chapter 5 38 main board cpu intel ® atom tm processor d525 chipset intel ® ich8-m system memory 1 x 204 pin ddr3 so-dimm socket, up to 4gb thermal solution fan-less os windows ® xp/ xpe/ wes, wepos, posready, windows ® 7 *, linux*, display tft lcd size 15” brightness 250 nits resolution 10...
Page 40: Itr-Cs15D
Itr-cs15d chapter 5 39 optional accessories customer display: vfd attached, 20 columns x 2 lines, rs-232 type msr-front type, 3 tracks, ps/2 type msr-side type, 3 tracks, ps/2 type & finger print, usb type msr-side type, 3 tracks, ps/2 type & i-button, ps/2 type 12.1” 2 nd display specifications are...