Remove machine from carton and place on a stable surface. Remove machine from plastic bag remove bubble-wrap from mandrills tcc 2700 laminating machine operating instructions tcc 2700 laminating machine tcc 2700 laminating machine operating instructions operating instructions.
Lower mandrill inside laminating roll upper mandrill inside the laminating roll lower heat roller upper heat roller operating panel tcc 2700 laminating machine tcc 2700 laminating machine tcc 2700 laminating machine.
Upper mandrill lower mandrill laminating roll laminating roll.
Insert upper and lower mandrills into core of the film line up film with appropriate notches on mandrill (25” film lines up with notch that reads “25”” and so forth).
Upper mandrill inside the laminating roll lower mandrill inside the laminating roll after inserting the upper and lower mandrills into the core of the film, it should look like the pictures shown below.
How to thread the laminating film how to thread the laminating film how to thread the laminating film shiny side dull side upper heat roller lower heat roller dull side shiny side laminating roll laminating roll upper mandrill lower mandrill threading bars.
Pass film over the first threading bar threading the upper laminating roll threading the upper laminating roll threading the upper laminating roll.
Pull film towards front and over the second threading bar threading the upper laminating roll threading the upper laminating roll threading the upper laminating roll.
Pass film over stable support rod threading the lower laminating roll threading the lower laminating roll threading the lower laminating roll.
Pass film under and back over the lower threading bar threading the lower laminating roll threading the lower laminating roll threading the lower laminating roll.
Threading the lower laminating roll threading the lower laminating roll threading the lower laminating roll pull through and over the upper threading bar.
Both ends of film should meet at heated rollers.
Switch on the machine set speed to “1” switching on the machine and setting switching on the machine and setting switching on the machine and setting.
Insert both ends of the film in-between the upper and lower heat rollers using the threading card (should come with the laminating rolls) once the film is fed fully through the machine, set lever to “up” position setting up the machine setting up the machine setting up the machine.
Set temperature to desired heat level and press the heat button at this time, the machine will take a few minutes to heat up at 80 degrees celsius, you will hear a beep from the machine. This is to let you know that when the temperature reaches 90 degrees, the rollers will start to turn. Press heat ...
Align the feed tray with appropriate notches, and set into place. Machine will beep once again when desired temperature is reached and green ready light will go on..
Lever should always be in “up” position when machine is not in use lever should be in “down” position when machine is in use lever positions lever positions lever positions.
Trim blade the trim blade is used to separate your current laminated project from the rest of the material. Caution: the blade is very sharp and should be used with utmost care . Run blade through material from left to right to cut finished product from the rest of the film. When not in use, trim bl...
Feed the papers to be laminated in between the upper and lower heat rollers, as shown above gently pull the laminated paper at the back. (if you don’t pull, the laminated paper might attach to the machine and get wrinkled, due to static electricity) feeding feeding feeding.
Set the temperature to 80 degrees celsius. Press cold button – the machine will start to cool down press and hold speed down button for 3 – 5 seconds to set the speed to “0”. (if running at a higher speed than “1”, reduce speed to “1” and then set to “0”) when the machine reaches 80 degrees celsius,...
Tension can be adjusted for the purpose of creating the right resistance for the rolls of laminating film. This is achieved by turning the silver knobs on the right side of the machine that line up with the upper and lower mandrills. To decrease tension, turn knob counter- clockwise. . To increase t...
Reverse button reverse button is used to back the film out in case of any jams or errors in lamination. When pressed, the film will feed back out towards the front of the machine. When released, the machine will start feeding the film normally again. Trouble shooting trouble shooting trouble shootin...
Ue buildup when machine is improperly heated to too high temperature or film is improperly aligned, you may notice markings along the side of the film where excess glue is building up on the rollers. To properly remove the glue, please use a non-abrasive cleaning solution (such as googone) that will...
Operating instructions manual operating instructions manual operating instructions manual refer the enclosed instructions manual for additional information.
