1. DL manuals
  2. Tanaka
  3. Trimmer
  4. TCG 24EBD (SL)
  5. Handling Instructions Manual

Tanaka TCG 24EBD (SL) Handling Instructions Manual

Manual is about: grass trimmer/brush cutter

Summary of TCG 24EBD (SL)

  • Page 1

    Grass trimmer/brush cutter model tcg 24ebs (sl) / tcg 24ebs (s) tcg 24ebd (sl) / tcg 24ebd (sln) tcg 27ebs (sl) / tcg 27ebs (s) tcg 27ebd (sl) / tcg 27ebd (sln) handling instructions note: before using this machine, carefully read through these handling instructions to ensure e ffi cient, safe operati...

  • Page 2

    2 meanings of symbols note: some units do not carry them. Symbols warning the following show symbols used for the machine. Be sure that you understand their meaning before use. It is important that you read, fully understand and observe the following safety precautions and warnings. Careless or impr...

  • Page 3

    3 10 10 13 8 6 2 5 4 17 13 11 9 8 14 9 11 7 15 14 6 2 19 18 20 tcg24ebs (sl) tcg27ebs (sl) 7 5 4 tcg24ebd (sl) tcg27ebd (sl) 16 21 2 9 11 13 8 7 6 5 14 4 5 12 3 1 13 11 9 15 2 8 7 tcg24ebd (sln) tcg27ebd (sln) tcg24ebs (s) tcg27ebs (s) what is what since this manual covers several models, there may ...

  • Page 4

    4 warnings and safety instructions operator safety ○ always wear a safety face shield or goggles. ○ always wear heavy, long pants and non-slip boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above shoulder length. ○ do not operate this...

  • Page 5

    5 caution do not disassemble the recoil starter. You may get a possibility of personal injury with recoil spring. Specifications model tcg24ebs tcg24ebd (sl) (s) (sl) (sln) engine displacement (cm 3 ) spark plug idling speed (min -1 ) speed of output shaft (min -1 ) max. Engine output (kw) 23.9 ngk ...

  • Page 6

    6 note when it is hard to insert drive shaft up to the marked position on the drive shaft tube, turn drive shaft by the cutter mounting end clockwise or counter-clockwise. Tighten tube locking bolt lining up the hole in the shaft tube. Then tighten clamp bolt securely. Installation of attachment 1. ...

  • Page 7

    7 installation of handle warning always use a barrier bar (6) and shoulder harness with the loop handle. ( fig. 3 ) 6 fig. 3 attach the handle to the drive shaft tube with the angle towards the engine. Adjust the location to the most comfortable position before operation. Note if your unit has handl...

  • Page 8

    8 fig. 12 installation of semi-auto cutting head 1. Function automatically feeds more nylon cutting line when it is tapped at low rpm (not greater than 4500 min -1 ). Speci fi cations code no. Type of attaching screw direction of rotation size of attaching screw 6696454 female screw counterclockwise...

  • Page 9

    9 3. Installation ( fig. 14 ) ○ install cutting head on gear case of grass trimmers/brush cutters. The mounting nut is left-hand-threaded. Turn clockwise to loosen/counterclockwise to tighten. 20 fig. 14 note ○ since the cutter holder cap is not used here, keep it for when a metal blade is used, if ...

  • Page 10

    10 fueling warning ○ always shut o ff the engine before refueling. ○ slowly open the fuel tank, when fi lling up with fuel, so that possible over-pressure disappears. ○ tighten the fuel cap carefully, after fueling. ○ always move the trimmer at least 3 m from the fueling area before starting. ○ alway...

  • Page 11

    11 fig. 25 15 m fig. 26 note press the quick release button or pull emergency release fl ap (if so equipped) in the event of emergency. ( fig. 25 ) warning if cutting attachment should strike against stones or other debris, stop the engine and make sure that the attachment and related parts are unda...

  • Page 12

    12 cleaning the air fi lter open the air fi lter cover and the fi lter (29). Rinse it in warm soap suds. Check that the fi lter is dry before reassembly. An air fi lter that has been used for some time cannot be cleaned completely. Therefore, it must regularly be replaced with a new one. A damaged f...

  • Page 13

    13 (5) insert both loose ends of the line through the cord guide (33) when placing the reel in the case. ( fig. 36 ) 32 33 fig. 36 note when placing a reel in the case, try to line up the stopper holes (32) with the cord guide (33) for easier line release later. (6) place the cover over the case so ...

  • Page 14

    14 list of recommended accessories type name speci fi cation loop handle bike handle multi purpose diameter feed system adapter or no. Of teeth (blade) blade thickness (mm) or trimmer line diameter (mm) tcg24ebs (sl) tcg27ebs (sl) tcg24ebs (s) tcg27ebs (s) tcg24ebd (sl) tcg27ebd (sl) aluminum heads ...

  • Page 15

    15 troubleshooting use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the tanaka dealer. Condition cause remedy engine does not start fuel system fuel tank is empty or fuel level is low fill the fuel tank with the...

  • Page 16

    16 condition cause remedy engine does not stop stop switch failure set the choke lever to start position to stop the engine cease use immediately and contact tanaka dealer engine stops when throttle is closed idle speed is too low contact tanaka dealer blade continues rotating when throttle is close...

  • Page 17

    17 tcg24ebs (sl) / tcg24ebs (s) / tcg24ebd (sl) / tcg24ebd (sln) a b 2 3 4 5 6 7 8 17 16 18 14 9 3 13 14 15 16 19 21 12 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 50 8 53 54 55 56 57 58 56 55 59 60 61 62 63 65 66 67 68 69 70 71 72 73 64 20 12 3 52 74 1 ...

  • Page 18

    18 tcg24ebs (sl) / tcg24ebs (s) tcg24ebd (sl) / tcg24ebd (sln) 157 151 152 158 159 160 154 155 156 161 164 165 166 167 168 163 178 177 169 170 171 172 173 174 175 176 179 193 192 194 195 196 184 185 186 187 188 189 190 191 501 502 503 504 505 507 506 178 183 204 199 205 206 207 506 203 162 167 171 1...

  • Page 19

    19 tcg27ebs (sl) / tcg27ebs (s) / tcg27ebd (sl) / tcg27ebd (sln) a b 9 1 2 1 3 4 5 6 7 16 15 17 13 8 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 50 52 53 54 55 56 57 58 59 56 55 60 61 62 63 64 66 67 68 69 70 71 10 72 73 74 6...

  • Page 20

    20 157 151 152 158 159 160 154 155 156 161 164 165 166 167 168 163 178 177 169 170 171 172 173 174 175 176 179 193 192 194 195 196 184 185 186 187 188 189 190 191 501 502 503 504 505 507 506 178 183 204 199 205 206 207 506 203 162 167 171 174 175 176 177 178 173 187 179 180 181 182 183 184 185 186 5...

  • Page 21

    21 000book̲tcg24ebs̲eng.Indb 21 000book̲tcg24ebs̲eng.Indb 21 2014/04/04 11:40:58 2014/04/04 11:40:58.

  • Page 22

    22 000book̲tcg24ebs̲eng.Indb 22 000book̲tcg24ebs̲eng.Indb 22 2014/04/04 11:40:58 2014/04/04 11:40:58.

  • Page 23

    23 000book̲tcg24ebs̲eng.Indb 23 000book̲tcg24ebs̲eng.Indb 23 2014/04/04 11:40:58 2014/04/04 11:40:58.

  • Page 24: Hitachi Koki Co., Ltd.

    311 code no. E99254713 na printed in china shinagawa intercity tower a, 15-1, konan 2-chome, minato-ku, tokyo, japan hitachi koki co., ltd. 02back̲tcg24ebs̲eng.Indd 24 02back̲tcg24ebs̲eng.Indd 24 2014/04/22 12:16:59 2014/04/22 12:16:59.