1. DL manuals
  2. TANDBERG
  3. Conference System
  4. 770
  5. User Manual

TANDBERG 770 User Manual

Manual is about: Videoconferencing System

Summary of 770

  • Page 1

    1 software version e3 d12788-05 this document is not to be reproduced in whole or in part without permission in writing from: user manual 990 / 880 / 770

  • Page 2

    2 tandberg videoconferencing system.

  • Page 3

    Tandberg videoconferencing system 3 environmental issues thank you for buying a product which contributes to a reduction in pollution and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consu...

  • Page 4

    4 tandberg videoconferencing system operator safety summary for your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, preca...

  • Page 5

    Tandberg videoconferencing system 5 contents introduction ........................................................................................ 7 menu structure ................................................................................... 8 the tandberg videoconferencing system ...............

  • Page 6

    6 tandberg videoconferencing system advanced use .................................................................................. 43 main menu ..................................................................................................... 43 call quality ........................................

  • Page 7

    Tandberg videoconferencing system 7 introduction this user manual is provided to help you make the best use of your tandberg system. The tandberg system offers superior audio and video quality in a fully-featured unit. The ‘welcome’ menu will show the name of your product. Main features: • supports ...

  • Page 8

    8 tandberg videoconferencing system menu structure the on-screen menu structure is shown below. Press the m enu key on the remote control to enter or leave the main menu. Call quality advanced settings main menu press u p /d own /l eft /r ight to navigate. Press o k to select. Ok mcu services audio ...

  • Page 9

    Tandberg videoconferencing system 9 the tandberg videoconferencing system remote control microphone camera codec.

  • Page 10

    10 tandberg videoconferencing system camera the built-in camera includes a high quality colour camera with a fast pan/tilt/zoom action. The camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Codec the codec is the heart of the system. The main task f...

  • Page 11

    Tandberg videoconferencing system 11 installation precautions • never install telephone wiring during a lightning storm. • never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. • never touch uninstalled telephone wires or terminals unless the tele...

  • Page 12

    12 tandberg videoconferencing system installation connecting cables 1. Microphone cable • connect the microphone to the microphone cable. • connect the microphone cable to microphone input 1 on the system. 2. Monitor cable(s) scart (europe): • connect the scart adapter to one of the scart connectors...

  • Page 13

    Tandberg videoconferencing system 13 installation 3. Isdn cables • cconnect the isdn cables to the isdn sockets (s/t-interface) provided by the service provider. Your main number will be the number associated with the socket to which isdn cable number 1 is connected. S ome systems and software versi...

  • Page 14

    14 tandberg videoconferencing system installation power on power on the monitor and use the monitor remote control to select the audio/video input used (refer to your monitor manual). If you are using s-video from the system, remember to select s-video input to avoid a black and white picture. Selec...

  • Page 15

    Tandberg videoconferencing system 15 installation system configuration • switch the system on by activating the power switch on the system. • after the system has performed a self-test routine, product logo and a ‘welcome’ menu will be displayed on the monitor. Connect menu p ress m enu on the remot...

  • Page 16

    16 tandberg videoconferencing system installation lan configuration • press m enu on the remote control. Select the menu ‘terminal settings’, then ‘lan settings’. Specify the necessary lan settings according to the instructions from your lan administrator. If there is an h.323 gatekeeper present on ...

  • Page 17

    Tandberg videoconferencing system 17 getting started getting started system start-up your system should be in standby mode. When in standby mode, pressing any key or picking up the remote control will wake up the system. An incoming call will also wake up the system. If the system does not respond, ...

  • Page 18

    18 tandberg videoconferencing system getting started basics the system’s most commonly used functions are accessible directly from the remote control by single key presses. In addition, the user interface is represented by on-screen menus. Individual items within the menus and lists can be selected ...

  • Page 19

    Tandberg videoconferencing system 19 getting started making and ending calls making a call to make a call, enter the number or the ip-address of the unit you wish to call using the dialing keys and press c onnect . Isdn call the system will, by default, try to connect using quality: auto (see table ...

  • Page 20

    20 tandberg videoconferencing system getting started tip access code if the system requires an access code, enter the code and press ok to proceed making a call: using sub-address / extension address / mcu password to specify an isdn sub-address or its lan equivalent extension address (tcs-4), add a...

  • Page 21

    Tandberg videoconferencing system 21 getting started selecting / setting default quality (bandwidth) t ype of calls auto 384kbps on isdn/768kbps on ip max 384kbps on isdn/1536kbps on ip 1472 1472 kbps (ip only) 1152 1152 kbps (ip only) 768 768 kbps (ip only) 512 512 kbps (ip only) 384 384 kbps (6b) ...

  • Page 22

    22 tandberg videoconferencing system getting started selecting / setting default network to select a specific network, press the ‘net’ quick key when you are in the dial menu.: 1 highlight the network to be used in your call. 2 press ‘select’ to select network or press ‘set as default’ to set the se...

  • Page 23

    Tandberg videoconferencing system 23 getting started answer a call to answer a call, press c onnect . Manual answer of a call is needed if the autoanswer facility is switched off. See ‘utilities’ in ‘advanced use’. End a call to end a call, press d isconnect . Correcting keying mistakes to delete th...

  • Page 24

    24 tandberg videoconferencing system getting started to find an entry, key in the first letter, for example t, and scroll with the up/down arrows. To dial the selected entry press c onnect . To edit the selected number before dialing, press ok (only point-to-point entries). Directory the directory i...

  • Page 25

    Tandberg videoconferencing system 25 getting started add new entry when selecting ‘add new entry, an empty directory entry is displayed: 1 move to ‘name’ and enter characters using the number keys on your remote control (as on mobile phones). Use ‘0’ to enter ‘space’, use ‘#’ to switch between upper...

  • Page 26

    26 tandberg videoconferencing system getting started add multisite entry when selecting ‘add multisite’, an empty multisite directory entry is displayed: 1 move to ‘name’ and enter the multisite meeting name. 2 select ‘add site’ to add meeting membergby searching for point-to-point entries in the di...

  • Page 27

    Tandberg videoconferencing system 27 general use mic off microphone on/off to mute your microphone during a call, press m ic o ff . An on screen indicator will appear when the microphone is off. In a call, if audio is detected, the on-screen symbol will start to flash. Pressing m ic o ff one more ti...

  • Page 28

    28 tandberg videoconferencing system general use do not disturb / sleep mode press any quick key when not in a call to activate the quick menu. When do not disturb is activated, the system will not accept any incoming calls. The caller will hear a busy tone when calling this unit. A status line will...

  • Page 29

    Tandberg videoconferencing system 29 general use selecting video sources press: to select the video source to be transmitted to the far end. Doc cam main cam vcr pc aux ok zoom controlling the main camera moving / zooming camera to control the main camera use the keys below: for pan/tilt and for zoo...

  • Page 30

    30 tandberg videoconferencing system general use voice activated camera positioning through voice activated camera positioning and the use of two microphones, the camera will automatically view the current speaker. Setup before using camera tracking, the camera positions used must be stored at prese...

  • Page 31

    Tandberg videoconferencing system 31 general use presets the preset buttons enable you to pre-store up to ten different settings. Each preset is able to store: • video source • camera position, pan/tilt/zoom/focus/brightness (if main camera) • audio source selection (see ‘audio settings’ in ‘advance...

  • Page 32

    32 tandberg videoconferencing system general use ok far end camera control (fecc) press the f ar e nd key until the ‘farendcamera’ on-screen indicator is displayed. For this feature to operate the far end must support ‘far end camera control’ (h.281). While activated you will be able to control the ...

  • Page 33

    Tandberg videoconferencing system 33 general use sending and receiving snapshots when a snapshot is sent, received or requested, it will be stored in the graphics memory. When a new image is sent or received, the old image will be erased. When disconnecting the call, the image will be erased. Sendin...

  • Page 34

    34 tandberg videoconferencing system general use * - optional feature. Duo video * duo video is useful if you want to display live video from your document camera or another camera in addition to live video of yourself. Add duo video • alt.1: press any other video source than maincam during a call. ...

  • Page 35

    Tandberg videoconferencing system 35 general use end a duo video call to end a duo video call, press d isconnect . Select if you want to disconnect only the duo video connection or the whole connection. Disconnect controlling camera, changing video source, presets in a duo video call the main monito...

  • Page 36

    36 tandberg videoconferencing system general use multisite (mcu)* the system has a built-in multipoint conference unit (mcu), multisite, which has the capability to establish meetings with up to 4 video sites (5 if at least one site is a telephone call, isdn/analogue/mobile). The video calls in a co...

  • Page 37

    Tandberg videoconferencing system 37 general use multisite cascading by connecting four multisite systems together, it is possible to connect up to 10 video sites (including the four multisite sites) plus 4 audio sites (telephones), see drawing below. The host can connect up to 3 other video systems...

  • Page 38

    38 tandberg videoconferencing system general use • press ‘add site’ to bring up the multisite dial menu. • enter the number to call. The quality will, by default, be the same as used by the first call. To place a telephone call instead of a video call, press ‘quality’ and select ‘teleph’ in the qual...

  • Page 39

    Tandberg videoconferencing system 39 general use disconnecting sites from a conference to disconnect a site or end the conference, press d isconnect . • select site and press o k or ‘disconnect site’. To end the meeting press ‘disconnect all’. Disconnect e ach system will be identified by a s ystem ...

  • Page 40

    40 tandberg videoconferencing system general use dc in 1 . Single 2 . Single video out audio out 3 . Dual 3 . Doc 4 . Vcr vga out 1 mic 1 2 mic 2 3 1 2 3 4 vcr 1 2 isdn bri ethernet i o pc presenter plugging a pc into the system is made extremely simple through the pc presenter, avoiding the need fo...

  • Page 41

    Tandberg videoconferencing system 41 general use web-interface it is possible to access and maintain the system remotely via a local area network (lan) using a standard web- browser. Connect your system to a local area network. Configure your codec: • press menu, select ‘terminal settings’, ‘lan set...

  • Page 42

    42 tandberg videoconferencing system general use t.120 / data dataport 1 com port t.120 and other pc applications a pc can be connected to the system using a serial cable. This will enable interactive editing, file transfer and application sharing between two computers. Appropriate communication sof...

  • Page 43

    Tandberg videoconferencing system 43 advanced use main menu the menu system can be used to select available functions and utilities for the system. To enter the menu system and the main menu, press the m enu key. You may leave the menu system at any time by pressing the m enu key. Menu password it i...

  • Page 44

    44 tandberg videoconferencing system advanced use call quality the call quality menu allows you to select the preferred quality of your call. D ue to actions or limitations at the far end you may not always be able to achieve the selections you want . Audio auto optimized audio quality depending on ...

  • Page 45

    Tandberg videoconferencing system 45 advanced use advanced call quality * - requires option ‘presenter’. To check which options are installed, see the ‘system info’ menu in ‘diagnostics’. Note t he ‘a uto ’ settings are recommended choices for most cases . T he other audio , video and resolution sel...

  • Page 46

    46 tandberg videoconferencing system advanced use presentations presentation mode to send a snapshot immediately after pressing s napshot select ‘presentation mode: normal’. To preview the image before it is transferred as a snapshot, select ‘presentation mode: preview’. When pressing s napshot you ...

  • Page 47

    Tandberg videoconferencing system 47 advanced use * - requires option ‘presenter’. To check which options are installed, see the ‘system info’ menu in ‘diagnostics’. Duo video number* auto when adding duo video in a conference, duo video is connected automatically if supported by the far end. Manual...

  • Page 48

    48 tandberg videoconferencing system advanced use utilities autoanswer on: the system will automatically answer all incoming calls. On+micoff: the system will automatically answer all incoming calls and switch the microphone off when the call is connected. Press m ic o ff to switch the microphone on...

  • Page 49

    Tandberg videoconferencing system 49 advanced use auto-pip on: your selfview will automatically be displayed as a pip (picture-in-picture) whenever the camera position or video source is changed. Picking up the remote control will also display your selfview. Welcome menu the welcome menu can be show...

  • Page 50

    50 tandberg videoconferencing system advanced use menu password enter the code which should be entered to get access to the menus on the tandberg system. When pressing the ‘menu’ button on the remote control, the user will be asked to enter the password written here. Web snapshots the system is able...

  • Page 51

    Tandberg videoconferencing system 51 advanced use mcu services a multipoint control unit (mcu) enables several sites to participate in the same conference. An mcu conference can have different modes: voice switched means that the image of the person currently speaking will be broadcast to all the ot...

  • Page 52

    52 tandberg videoconferencing system advanced use quick menu when connected to an mcu p ress any q uick key when in a multipoint conference to activate the q uick m enu . This menu provides access to the most commonly used mcu functions. If ‘ request floor’ is selected, ‘request floor’ will change t...

  • Page 53

    Tandberg videoconferencing system 53 advanced use request floor when requesting the floor, the mcu will broadcast your video in full screen to all other participants in the conference. If the mcu conference has a chairman, a floor request is sent to the chairman. You will remain ‘on air’ until eithe...

  • Page 54

    54 tandberg videoconferencing system advanced use chair control * you select ‘chair control’ and ‘take chair’ to assume the role of chairman of the ‘meeting’. As chairman, you may control which site you and the other sites see. Take chair allows you to request chairmanship of the conference. If no o...

  • Page 55

    Tandberg videoconferencing system 55 advanced use audio settings audio inputs by default, all inputs are enabled. Just plug in an audio source and it is active. Audio inputs that are on will automatically be mixed. Select off to prevent audio/noise from unused inputs or if you want to disable a spec...

  • Page 56

    56 tandberg videoconferencing system advanced use audio input 4 is intended for connection to a vcr. It can also be connected to other external playback devices. As there is no acoustic echo canceller on this input it should not be connected to any microphones. The audio source connected to this inp...

  • Page 57

    Tandberg videoconferencing system 57 advanced use audio outputs audio out 1 is intended for connection to televisions or audio amplifiers. Audio out 2 is intended for connection to a vcr or other recording equipment. The signal is a mix of audio from far end and local end. N ever connect audio out 2...

  • Page 58

    58 tandberg videoconferencing system advanced use echo control each of the 2 microphone inputs have a separate echo canceller. One echo canceller per input provides more sophisticated control than having one common canceller for all microphones. Echo control is normally set to ‘on’ to prevent the fa...

  • Page 59

    Tandberg videoconferencing system 59 advanced use room size this setting allows optimization of the echo canceller to the acoustic size of the room. Hard walls, many windows etc. Might require higher settings than expected. Carpets, curtains etc. Might require lower settings. Adjust the setting (not...

  • Page 60

    60 tandberg videoconferencing system advanced use automatic gain control (agc) settings select ‘on’ to allow automatic adjustments (automatic gain control) of audio levels. When ‘on’, the agc maintains the audio signal level at a fixed value by attenuating strong signals and amplifying weak signals....

  • Page 61

    Tandberg videoconferencing system 61 advanced use alert tones & volume to help distinguish between incoming video calls and ordinary telephone calls, different ringing tones may be selected. You may also select different volume levels for the ringing tone. Alert speaker the system also has an intern...

  • Page 62

    62 tandberg videoconferencing system advanced use video settings camera tracking mode select the camera tracking mode: slow: the system waits a while before zooming in on a single person speaking. Suitable when wide-angle images are preferred over close-up images. Norm: should be used in regular mee...

  • Page 63

    Tandberg videoconferencing system 63 advanced use focus to manually adjust the focus select ‘manual’ and use the arrow keys to adjust. Brightness to manually adjust the brightness select ‘manual’ and use the arrow keys to adjust. Whitebalance in auto mode the whitebalance is continuously updated. To...

  • Page 64

    64 tandberg videoconferencing system advanced use vga settings vga out to enhance the local video quality, a vga monitor may be connected. Main: should be used if you want to use a vga monitor as your main monitor. Video outputs 1 and 2 will be disabled. Dual: should be used if you want to use a vga...

  • Page 65

    Tandberg videoconferencing system 65 advanced use address the ip-address of the pc with the vnc software installed. To find the ip-address of the pc, select ‘command prompt’ from the startup-menu. Type ‘ipconfig’ and press enter. Display number the display number for vnc is 0 and upwards. If you are...

  • Page 66

    66 tandberg videoconferencing system advanced use isdn-bri settings s ome software versions do not support 3 isdn lines , therefore some of the l ine s etup lines may be grayed out . I f n ational isdn is selected , press the q uick key ‘a uto bri c onfig ’ to request an automatic configuration of t...

  • Page 67

    Tandberg videoconferencing system 67 advanced use 1tr6 should only be used if you are operating the system behind a pabx. Note isdn switch type select the type of isdn network connected to your unit.

  • Page 68

    68 tandberg videoconferencing system advanced use line setup this menu allows you to program the numbers associated with your isdn line. If you want to use this isdn line, you need to set ‘enabled: on’ and enter the numbers of your isdn line. If some of the isdn lines are not to be used, set ‘enable...

  • Page 69

    Tandberg videoconferencing system 69 advanced use subaddress using a subaddress enables you to connect up to eight isdn terminals to the same isdn telephone number and line. The terminals are addressed by using different subaddresses. To call a terminal with a subaddress, separate the isdn telephone...

  • Page 70

    70 tandberg videoconferencing system advanced use msn (multiple subscriber number) the use of msn (multiple subscriber number) enables you to attach different isdn terminals, with different numbers, to the same physical isdn telephone line. If ‘validate numbers’ is set to ‘on’ only calls to those nu...

  • Page 71

    Tandberg videoconferencing system 71 advanced use address address is defined as the ip-address of a streaming client, streaming server or a multicast address. Giving an address in the range 224.0.0.1-239.255.255.255 will broadcast the stream to any host that has joined the specified multicast group....

  • Page 72

    72 tandberg videoconferencing system advanced use streaming source auto enables streaming of both local and far end video. Selection of which site to be streamed is done using voice switching (the site that speaks is streamed). Local only the local video will be streamed. Remote only the far end vid...

  • Page 73

    Tandberg videoconferencing system 73 advanced use h.323 settings e.164 alias this is the e.164 address of the codec. The e.164 address is equivalent to a telephone number, sometimes combined with access codes. Valid characters are 0-9,* and #. When using a gatekeeper the codec will send a message to...

  • Page 74

    74 tandberg videoconferencing system advanced use use callmanager on the codec will use a specific cisco callmanager identified by the ip-address specified in ‘callmanager ip’. The callmanager replaces a gatekeeper, therefore ‘use gatekeeper’ must be set to ‘off’ before this can be done. When ‘on’, ...

  • Page 75

    Tandberg videoconferencing system 75 advanced use advanced h.323 settings t hese settings only have an effect if they are supported by your ip infra structure . Note rsvp auto resource reservation protocol enables the endpoints to request the optimal amount of bandwidth for the duration of an ip vid...

  • Page 76

    76 tandberg videoconferencing system advanced use ip precedence used to define which priority audio, video, data and signalling should have in the network. Higher numbers indicate higher priority. The priority ranges from 0(off) - 7 for each type of packets . Diffserv used to define which priority a...

  • Page 77

    Tandberg videoconferencing system 77 advanced use ip settings ip-assignment dhcp (dynamic host configuration protocol) can be selected when a dhcp server is present. Dhcp: ip-address, ip-subnet mask and gateway are not used because these parameters are assigned by the dhcp server. Static: the codec’...

  • Page 78

    78 tandberg videoconferencing system advanced use ethernet speed auto the codec will auto-detect the speed/duplex on the lan. 10/half the codec will connect to the lan using 10mbps speed/half duplex. 10/full 10 mbps speed/full duplex. 100/half 100 mbps speed/half duplex. 100/full 100 mbps speed/full...

  • Page 79

    Tandberg videoconferencing system 79 advanced use wireless lan settings ssid (service set identification) example “wlannetwork”. Defines a local network id for this wireless region. It must be the same for all end points and the access point. An endpoint will find the access point if the ssid is cor...

  • Page 80

    80 tandberg videoconferencing system advanced use encryption encryption using hex numbers the 64-bit keys can consist of 10 hexadecimal digits. Example: “de01ad4dbe”. The 128-bit key can consist of 26 hex numbers. Encryption select if you want to encrypt your wireless lan connection. Use key select ...

  • Page 81

    Tandberg videoconferencing system 81 advanced use note snmp trap host snmp (simple network management protocol) is used for monitoring and configuring different units in a network. The codec’s snmp agent responds to requests from snmp managers (a pc program etc.). Snmp traps are generated by the age...

  • Page 82

    82 tandberg videoconferencing system advanced use call settings incoming mcu calls on: when you are in a call, the system will provide visual and audible indications of an incoming call and ask you to accept/reject the call. Off: the system will not accept incoming calls when you are in a call. Inco...

  • Page 83

    Tandberg videoconferencing system 83 advanced use * optional feature encryption (secure conference)* auto the system will try to set up calls using encryption. Point to point calls: if the far end system supports encryption, the call will be encrypted. If not, the call will proceed without encryptio...

  • Page 84

    84 tandberg videoconferencing system advanced use this menu consists of 6 network profiles, a prefix can be added for each profile. If you add a prefix to a profile, this prefix will automatically be added to the number being dialed. E xample : 0 is added as a c all p refix to the 2 nd profile , isd...

  • Page 85

    Tandberg videoconferencing system 85 advanced use dataport configuration the system provides one standard rs232 serial port to allow a computer to be connected for data transfer and control purposes. W hen connecting to a pc the connecting cable must be a straight through rs232 cable . Dataport 1 if...

  • Page 86

    86 tandberg videoconferencing system advanced use dataport 2 dataport 2 is dedicated to the main camera and will not be available in standard configuration. The codec will automatically detect wave cameras. If you are using a camera supporting the visca protocol, select ‘mode: visca’. The dataport 2...

  • Page 87

    Tandberg videoconferencing system 87 advanced use software options the system requires a valid option key to activate security (contains secure conference aes), multisite and/or presenter functionality. A restart of the system is required after entering a new option key. If the option key is invalid...

  • Page 88

    88 tandberg videoconferencing system advanced use diagnostics allows testing of individual system components and displays the current system settings. Ok system info select ‘ system info’ to view system numbers, line status, software version and other useful information. Channel status comprehensive...

  • Page 89

    Tandberg videoconferencing system 89 advanced use the numbers used to call out to the far end are shown in the window. If an error occurs a cause code will be displayed on the right hand side of the window. P ress m enu and then ’c all s tatus ’ to bring this menu up when not in the menu system . Ti...

  • Page 90

    90 tandberg videoconferencing system advanced use please contact your tandberg representative for further information. Call status comprehensive information about the call is available through the call status window. The menu has two columns, one for transmitted and one for received audio/video/data...

  • Page 91

    Tandberg videoconferencing system 91 advanced use test subsystem you can test the different subsystems of your videoconferencing equipment. Far end loop (isdn only) setlocal: this system will loop all incoming audio and video. · the far end will see its own video and hear its own audio. · the local ...

  • Page 92

    92 tandberg videoconferencing system advanced use view current settings this window will display all the system settings. Use the arrow keys to scroll through the list. Restore defaults you may restore all system settings to the factory default using this function. T his default setting will not aff...

  • Page 93

    Tandberg videoconferencing system 93 peripherals peripheral equipment using the optional peripheral devices outlined in this chapter and the many others available, you will be able to build your own applications for use with the system, thereby better integrating the system into your business enviro...

  • Page 94

    94 tandberg videoconferencing system peripherals 5 video inputs • 1 video input used by the built-in camera. • 1 video input supporting s-video through a mini-din connector. • 2 video inputs supporting composite signals through rca connectors. • 1 vga input supporting resolutions vga(640x480), svga(...

  • Page 95

    Tandberg videoconferencing system 95 peripherals dual monitor it is possible to install the system in a dual monitor configuration. The dual monitor can be used to show full screen selfview, still images and duo video. To use the system in the dual monitor configuration: • connect ‘video out 3’ (com...

  • Page 96

    96 tandberg videoconferencing system peripherals document camera a document camera can be used for showing text, diagrams and a variety of graphical material as well as small three-dimensional objects. To use a document camera with your system: • connect the document camera to the doccam input on th...

  • Page 97

    Tandberg videoconferencing system 97 peripherals 1. Single 2. Single video out audio out 3. Dual 3 . Doc 4 . Vcr vga out 1 mic 1 2 mic 2 3 4 vcr 1 2 1 . Single 2 . Single video out audio out 3 . Dual 3 . Doc 4 . Vcr vga out 1 mic 1 2 mic 2 3 4 vcr 1 2 video cassette recorder (vcr) vcr - playback for...

  • Page 98

    98 tandberg videoconferencing system peripherals extra fixed cameras you can connect extra fixed cameras to your system, for example, a whiteboard camera. Connect the video output of the additional camera to one of the available video in sockets on the system. Additional microphones if your environm...

  • Page 99

    Tandberg videoconferencing system 99 appendices appendices appendix 1: connecting the system to isdn using nt1 network adapters connecting connect the first isdn cable from isdn 1 on the codec to the s-interface on your first nt1 network adapter. Connect the other isdn cables to the appropriate nt1 ...

  • Page 100

    100 tandberg videoconferencing system appendices appendix 2: connecting the system to the switched 56 network using telesync ts-256 sw56/isdn adapter connecting the system to the sw56 network using a telesync adapter is described below. Note: there are different telesync adapters for different confi...

  • Page 101

    Tandberg videoconferencing system 101 appendices appendix 3: environmental considerations this section explains how to carry out basic adjustments and simple tests to ensure that you send and receive the best possible image and audio quality when using your system. Iris control and lighting by defau...

  • Page 102

    102 tandberg videoconferencing system appendices how to prepare a typical room for videoconferencing the diagram below shows a typical room designed to obtain the best results when using the system. The microphone should be placed at the front of the table to ensure that all speech will be detected....

  • Page 103

    Tandberg videoconferencing system 103 appendices appendix 4: using the file system it is possible to access a file system within the tandberg system by using ftp: dos-window: ftp , or web-browser: ftp:// description of the different files all.Prm - all settings in the system (including directory) di...

  • Page 104

    104 tandberg videoconferencing system appendices custom logos · go to the folder where your logo is located. L ogo max size : 704 x 480 file - format : jpg . I f the file is too large , no logo will be displayed . · type ftp . · go to the user folder, type “cd user” · upload the logo, type put the n...

  • Page 105

    Tandberg videoconferencing system 105 appendices menu password: access to the menu system on the tandberg videoconferencing unit can be controlled using password protection. This is done by using the following dataport command: menupassword set . The pin-code should be maximum 5 - five digits. To er...

  • Page 106

    106 tandberg videoconferencing system appendices streaming password by setting a streaming password in the streaming menu on the tandberg codec, a password have to be entered on the streaming client to be able to see the videostream from the tandberg videoconferencing unit. Ip password by setting a ...

  • Page 107

    Tandberg videoconferencing system 107 appendices * - optional feature encryption all tandberg systems support both aes* and des encryption. By default this feature is enabled such that when connecting with any other video system or mcu, a tandberg system will attempt to establish a secure conference...

  • Page 108

    108 tandberg videoconferencing system appendices appendix 6: declaration of conformity.

  • Page 109

    Tandberg videoconferencing system 109 index index a access code 20, 81, 104 add duo video 34 add multisite entry 26 add new entry 25 adding an extra site 38, 39 additional microphone 97 adjusting volume 27 advanced call quality 45 advanced isdn settings 69 advanced use 43 aes 82, 106 alert speaker 6...

  • Page 110

    110 tandberg videoconferencing system index interfaces 92 introduction 7 ip address conflict check 91 ip password 105 ip-address 76 ip-subnet mask 76 iris control and lighting 100 isdn switch type 67 isdn-bri settings 66 k key tones 61 l line setup 68 logo 103, 106 loudspeaker volume 100 m making a ...

  • Page 111

    Tandberg videoconferencing system 111 to adjust the volume 27 to answer a call 23 to call a terminal with a sub-address 69 to connect a pc to dataport 1 84 to end a call 23 to enter/leave the menu system 43 to manually focus the main camera 29 to select a preset 31 to store the current camera positi...