- DL manuals
- TANDBERG
- Network Card
- D1392602
- User Manual
TANDBERG D1392602 User Manual
Summary of D1392602
Page 1
Tandberg video portal data port command interface user guide tandberg video portal data port command interface user guide software version v 3 d1392602 tandberg d1392602 1.
Page 2: Table of Contents
Tandberg video portal data port command interface user guide table of contents 1. Introduction .......................................................................................................................... 3 2. Connecting to the data port command interface through the rs-232 port. 4 2.1....
Page 3
Tandberg video portal data port command interface user guide 1. Introduction the tandberg video portal data port command interface user guide contains guidelines on how to use the textual command interface supported by the video portal system, further referred to as video portal. The data port comma...
Page 4
Tandberg video portal data port command interface user guide 2. Connecting to the data port command interface through the rs-232 port. The rs-232 portis a 9-pin, female, sub-d connector located on the front of the video portal. The port is configured as a dce (data communications equipment). The rs-...
Page 5
Tandberg video portal data port command interface user guide d1392602 5 if communication cannot be established between the pc/terminal and the tandberg video portal’s data port the following should be checked: • verify that the serial cable is a straight through 9-pin to 9-pin cable • confirm that t...
Page 6
Tandberg video portal data port command interface user guide 3. Connecting to the data port command interface using telnet the tandberg video portal has one lan port. The video portal’s telnet server provides access to the data port command interface through a 10/100 base t network interface support...
Page 7
Tandberg video portal data port command interface user guide 4. The tandberg video portal commands 4.1. Introduction typing ‘?’ or ‘help’ when connected to the data port command interface will return a list of valid commands. The commands are used to control the functions of the video portal. A comm...
Page 8
Tandberg video portal data port command interface user guide • user commands, xcom. Parameter configuration commands are commands that set a system parameter to a specific value. E.G.: the command xconf telnet mode: "on" enables telnet access on the video portal. If the command is syntactically corr...
Page 9
Tandberg video portal data port command interface user guide 4.2.1. System configuration commands command: description: alplan mapping of a call onto a service or another call. Dialplan entry [1..64] enabled: dialplan entry [1..64] name: dialplan entry [1..64] nettype: dialplan entry [1..64] prefix:...
Page 10
Tandberg video portal data port command interface user guide distinguished: • net type - either h324m, h323 or sip of the outbound call. • av mode – this mode determines the outbound audio and video call settings. It is either audio only, audio + video, auto(matic) no fallback to audio, auto + fallb...
Page 11
Tandberg video portal data port command interface user guide *c xconfiguration dialplan entry 1 prefix: "207947133" *c xconfiguration dialplan entry 1 suffix: "" *c xconfiguration dialplan entry 1 serviceid: 1 *c xconfiguration dialplan entry 1 property 1 name: "nettype" *c xconfiguration dialplan e...
Page 12
Tandberg video portal data port command interface user guide *c xconfiguration dialplan entry 2 property 2 name: "avmode" *c xconfiguration dialplan entry 2 property 2 value: "4" *c xconfiguration dialplan entry 2 property 3 name: "prefix" *c xconfiguration dialplan entry 2 property 3 value: "" *c x...
Page 13
Tandberg video portal data port command interface user guide *c xconfiguration dialplan entry 4 prefix: "90370010" *c xconfiguration dialplan entry 4 suffix: "" *c xconfiguration dialplan entry 4 serviceid: 3 *c xconfiguration dialplan entry 4 property 1 name: "allowredirectep" *c xconfiguration dia...
Page 14
Tandberg video portal data port command interface user guide *c xconfiguration dialplan entry 4 property 14 name: "entry5_label" *c xconfiguration dialplan entry 4 property 14 value: "menu" *c xconfiguration dialplan entry 4 property 15 name: "entry5_nettype" *c xconfiguration dialplan entry 4 prope...
Page 15
Tandberg video portal data port command interface user guide xconf h323gatekeeper authentication *c xconfiguration h323gatekeeper authentication address: “abc.Def.Ghi.Jkl” *c xconfiguration h323gatekeeper authentication mode: off *c xconfiguration h323gatekeeper authentication id: "" http enables or...
Page 16
Tandberg video portal data port command interface user guide • gateway: sets the gateway ip address. If a gateway is located on the lan and the video portal needs to reach nodes through this gateway, the gateway address can be set using the gatewayvariable (the ip address of the gateway will be set ...
Page 17
Tandberg video portal data port command interface user guide or sip interface transport default: --- sub-commands: • mode: specifies whether the system uses a default sip proxy. • address: specifies the ipv4 address or fqdn of the sip proxy. • type: specifies the type of the sip proxy. • transport d...
Page 18
Tandberg video portal data port command interface user guide *c xconfiguration snmp systemcontact: "" *c xconfiguration snmp systemlocation: "" *c xconfiguration snmp hostipaddr 1: "127.0.0.1" *c xconfiguration snmp hostipaddr 2: "127.0.0.1" *c xconfiguration snmp hostipaddr 3: "127.0.0.1" ssh enabl...
Page 19
Tandberg video portal data port command interface user guide 4.2.2. General video portal commands command: description: externalmanager this command sets the path and address of the tms server. A message is sent to tms when the video portal starts up to signal tms that the video portal is ready. Ext...
Page 20
Tandberg video portal data port command interface user guide 4.2.3. System status commands command: description: dialplan shows the dialplan configuration. Example: *s dialplan 1: entry: dialplanentryid: 1 enabled: on name: "h323 - sip" nettype: h323 prefix: "9047123456" suffix: "" serviceid: 2 prop...
Page 21
Tandberg video portal data port command interface user guide ethernet displays the configuration of the ethernet interface ethernet status format: --- parameters: • macaddress, the mac address of the ethernet interface • speed, the speed of the interface, possible values are auto/10half/10full/100ha...
Page 22
Tandberg video portal data port command interface user guide expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" expression: "" *s/end h323gatekeeper displays the status of...
Page 23
Tandberg video portal data port command interface user guide name> --- parameters: • address, the ip address of the video portal • subnetmask, the subnetmask used for the connected network • gateway, the gateway to route traffic to an ip number outside the connected network • dns server [1.. 5] addr...
Page 24
Tandberg video portal data port command interface user guide options parameters: ---- example of options feedback: *s options: option 1: key: "115201p1-1-43f072fc" description: "1 trunk" *s/end service displays all configured/uploaded services. Service status format: service [1..64] example of servi...
Page 25
Tandberg video portal data port command interface user guide status format: version> name> releasedate> configuration telephony:> videotelephony:> version> serialnumber> mainboard> additionalboard> configuration: pri> temperaturecelcius> temperaturefahrenheit> --- parameters: • producttype, the name...
Page 26
Tandberg video portal data port command interface user guide configuration: pri:41 temperaturecelcius: na temperaturefahrenheit: na *s/end 4.2.4. Debug commands command: desription: syslog enables a real-time log of bonding, h.221 and h324m, isdn, rtsp, ivider, and ivider engine activity. Note! H323...
Page 27
Tandberg video portal data port command interface user guide example: xcommand boot *r result (status=ok): / *r/end ok cuil reboot request, restarting checkdisk this command shows the presence and the status of the internal harddisk. Example: xcommand checkdisk *r result (status=ok): checkdisk: "dis...
Page 28
Tandberg video portal data port command interface user guide dial this command establishes a dial out to an end point parameters: • calledparty:.
Page 29
Tandberg video portal data port command interface user guide example: xcommand disconnectcall abcd123456 *r result (status=ok): *r/end ok erasedisk this command wipes all the data from the internal harddisk example: xcommand erasedisk *r result (status=ok): *r/end ok feedbackderegister command used ...
Page 30
Tandberg video portal data port command interface user guide • cause: cause code specifying why the command was not accepted by the system • description textual description of the cause code. Example: xcommand feedbackregister url:http://10.47.14.185:8000 expression.1:status/call expression.2:status...
Page 31
Tandberg video portal data port command interface user guide example (delete service nr. 10): xcommand serviceentrydelete 10 *r result (status=ok): / *r/end ok serviceentryswap command used to swap service numbers. Parameters: • serviceentrynumber(r): • serviceentrynumber2(r): example (swap service ...
Page 32
Tandberg video portal data port command interface user guide general user commands about shows following system information: software version: r3.0 portions of this software are licensed under 3rd party licenses. See the cd accompanying this product for details. Help or ? Displays the help menu. Hel...
Page 33
Tandberg video portal data port command interface user guide d1392602 33 "xfeedback register status/call" - to monitor call changes "xfeedback register status/call--" - to monitor only call state changes "xfeedback register configuration" - to monitor all configuration changes xhistory the special c...