- DL manuals
- TANDBERG
- Media Converter
- EN8000
- Reference Manual
TANDBERG EN8000 Reference Manual - 5.12.2
Web Browser Interface — Stored Configuration Tab
Page 5-60
Reference Guide: EN8000 MPEG-4 Part 10 (H.264/AVC) Encoders
ST.RE.E10233.1
5.12.2
Load Config n (From Flash Memory) Option
This options loads the parameters from one of the configuration files into the operational set
for the Encoder.
Figure 5.28: Typical Stored Configurations Tabbed Page
5.12.3
Save Config to Flash Memory Option
This option saves the parameters from the operational set for the Encoder into one of the
configuration files.
5.13 Load/Save
The instructions shown on the screen should be followed to perform the required operation.
NOTE…
The facility to save/load XML configurations is currently intended to be used under the direction of
TANDBERG Television support staff.
Summary of EN8000
Page 1
St.Re.E10233.1 issue 1 reference guide en8000 mpeg-4 part 10 (h.264/avc) encoders software version 1.0 (and later) en8030 standard definition encoder en8090 high definition encoder.
Page 2
Preliminary pages page ii reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 issue 1 first published in 2007 by: t andberg t elevision l td r egistered a ddress : u nit 2 s trategic p ark , c omines w ay , h edge e nd , s outhampton , h ampshire , so30 4da u nited k ingdom re...
Page 3: List of Contents
Preliminary pages reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page iii st.Re.E10233.1 list of contents chapter 1: introduction to the basic encoder this chapter gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and c...
Page 4: About This Reference Guide
Preliminary pages page iv reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 about this reference guide this reference guide provides instructions and information for the installation and operation of the en8000 encoder range. This reference guide should be kept in a safe pla...
Page 5: Acknowledgements
Preliminary pages reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page v st.Re.E10233.1 acknowledgements general all best endeavours have been made to acknowledge registered trademarks and trademarks used throughout this manual. Any notified omissions will be rectified in the next issue ...
Page 6: Warnings, Cautions and Notes
Preliminary pages page vi reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 warnings, cautions and notes heed warnings all warnings on the product and in the operating instructions should be adhered to. The manufacturer cannot be held responsible for injuries or damage where...
Page 7: Contact Information
Preliminary pages reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page vii st.Re.E10233.1 contact information tandberg television customer services support services our primary objective is to provide first class customer care that is tailored to your specific business and operational re...
Page 8: Technical Training
Preliminary pages page viii reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 technical training training courses tandberg television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. Tandberg can...
Page 9: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-1 st.Re.E10233.1 chapter 1 1. Introduction to the basic encoder contents 1.1 scope of this reference guide ......................... 1-3 1.1.1 who should use this reference guide ..................................................... ...
Page 10
Introduction to the basic encoder page 1-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 11: 1.1
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-3 st.Re.E10233.1 1.1 scope of this reference guide 1.1.1 who should use this reference guide this reference guide is written for operators/users of the en8000 range of encoders to assist in the insta...
Page 12: 1.1.4 Optional
Introduction to the basic encoder page 1-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 1.1.4 optional features this guide is intended to cover all features and functions of the unit. However some of these features may be purchasable options or features that have not be...
Page 13: 1.3 Video
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-5 st.Re.E10233.1 1.3 video encoding 1.3.1 sd video inputs (en8030 encoder) the standard video inputs are: • sdi - serial digital interface - itu-r bt.656-4, part 3 (d1 serial format) – smpte 259 (com...
Page 14: 1.3.2
Introduction to the basic encoder page 1-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 output on video loss in the event of video input loss the encoder can be software-configured to show either: • a test pattern (with or without identification text). • a freeze frame ...
Page 15: 1.3.3 Video
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-7 st.Re.E10233.1 downsampler note… availability of this option requires the en8000/swo/pip licence. A downsampler is implemented for the hd-sdi input. The output of the downsampler is either: • 720 x...
Page 16: 1.4 Audio
Introduction to the basic encoder page 1-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 1.4 audio encoding 1.4.1 audio inputs (en8090 hd encoder) the standard audio inputs are: • audio in 2 - this 15-way male d-type connector can be used for the input of up to four ster...
Page 17: 1.4.2
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-9 st.Re.E10233.1 1.4.2 audio inputs (en8030 sd encoder) the standard audio input is: • audio in 2 - this 15-way male d-type connector can be used for the input of up to four stereo pairs of aes/ebu d...
Page 18: 1.4.3 Audio
Introduction to the basic encoder page 1-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 1.4.3 audio encoding the available audio algorithms that can be used to encode the input audio are: aac (mpeg-2 and mpeg-4) the encoder has the capability of encoding incoming audio...
Page 19: 1.5
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-11 st.Re.E10233.1 dolby digital if licensed, the encoder can encode incoming audio at a sampling rate of 48 khz to a dolby digital compliant bitstream for the ts output only. Dolby digital audio enco...
Page 20: 1.6 Guided
Introduction to the basic encoder page 1-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 the encoder has the ability to extract vbi data from line number ranges 10-22 and 272-285 for 525 lines and 6-23 and 318-335 for 625 lines. The specifications surrounding vbi data a...
Page 21: 1.6.3
Introduction to the basic encoder reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 1-13 st.Re.E10233.1 figure 1.2: front panel indicators 1.6.3 rear panel description the encoder provides connectors at the rear panel (see chapter 2, installing the equipment). All, except the power co...
Page 22
Introduction to the basic encoder page 1-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 23: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-1 st.Re.E10233.1 chapter 2 2. Installing the equipment contents 2.1 introduction ....................................................... 2-3 2.1.1 read this first!...................................... 2-3 2.1.2 site requirements .......
Page 24
Installing the equipment page 2-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 list of tables table 2.1: supply cable wiring colors ................................. 2-7 table 2.2: sdi connector.................................................... 2-11 table 2.3: h sync c...
Page 25: 2.1 Introduction
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-3 st.Re.E10233.1 2.1 introduction 2.1.1 read this first! The encoder must be handled carefully and thoughtfully to prevent safety hazards and damage. It is usually supplied as part of a system installed by tan...
Page 26: 2.2 Preliminary
Installing the equipment page 2-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communi...
Page 27: 2.3.2 Cable
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-5 st.Re.E10233.1 figure 2.1: fitting the encoder into a rack 2.3.2 cable routing power supply cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them...
Page 28: 2.4
Installing the equipment page 2-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 figure 2.2: air path through the enclosure 2.4 a.C. Mains operating voltage and earthing 2.4.1 a.C. Power supply caution… this product should be operated only from the type of power source ind...
Page 29
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-7 st.Re.E10233.1 table 2.1: supply cable wiring colors uk (bs 1363) europe (cee 7/7) usa (nema 5-15p) earth: green-and-yellow green-and-yellow green neutral: blue blue white live: brown brown black protective ...
Page 30: 2.5
Installing the equipment page 2-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 2.5 -48 vdc power supply 2.5.1 d.C. Power supply note… only model en8030/bas/48v and en8090/bas/48v use a d.C. Power supply. Caution... This product should be operated only from the type of po...
Page 31: 2.5.4
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-9 st.Re.E10233.1 connect the encoder to the local d.C. Power supply as follows. 1. Local d.C. Power supply ensure the local d.C. Supply is isolated. 2. Encoder ensure the correct fuse is fitted. 3. Supply cord...
Page 32: 2.6.2
Installing the equipment page 2-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 2.6.2 connecting up the basic encoder once the unit has been installed in its intended operating position, it is ready to be connected up to the rest of the system equipment (see figure 2.5 )...
Page 33: 2.6.3 Power
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-11 st.Re.E10233.1 2.6.3 power supply section 2.4, a.C. Mains operating voltage and earthing and section 2.5, -48 vdc power supply provides details of the a.C power supply connection, protective earthing and sa...
Page 34: 2.6.6 Audio
Installing the equipment page 2-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 table 2.4: comp video connector pin signal centre video input screen video input return impedance 75 Ω hd-sdi in a 75 Ω bnc connector as described in table 2.5 provides a serial digital video...
Page 35: 2.6.7
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-13 st.Re.E10233.1 audio in connect the audio cable to the audio in connector. The 15-way, d-type male connector is used in different ways according to the audio input and the encoding configuration selected. T...
Page 36: 2.6.8 Control
Installing the equipment page 2-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 2.6.8 control interfaces connection operation of the encoder from a tandberg television control system is via the control ethernet network running a web browser or ncompass control on a remot...
Page 37: 2.6.9 Data
Installing the equipment reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder page 2-15 st.Re.E10233.1 2.6.9 data rs-232 connector a 9-way, d-type female connector provides an rs-232 asynchronous, serial communications data input interface. Table 2.11: rs-232 data connector (base board) - asyn...
Page 38: 2.7 Powering
Installing the equipment page 2-16 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoder st.Re.E10233.1 aux data out hd-sdi output. This output is not guaranteed to meet the hd-sdi specification. Aux rs-232 a 9-way, d-type male connector provides an rs232 connection for use by tandberg televisi...
Page 39: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 3-1 st.Re.E10233.1 chapter 3 3. Options and upgrades contents 3.1 what’s available................................................ 3-3 3.1.1 hardware options .................................. 3-3 3.1.2 limitations on number of option ...
Page 40
Options and upgrades page 3-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 41: 3.1 What’S
Options and upgrades reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 3-3 st.Re.E10233.1 3.1 what’s available 3.1.1 hardware options the basic encoder functionality can be enhanced with the inclusion of options, hardware and software. A hardware option module consists of a horizontal...
Page 42: 3.1.3 Software
Options and upgrades page 3-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 3.1.3 software options when the appropriate software option has been purchased it is enabled in the encoder, which resets and displays the appropriate menu items. See table 3.2 for the software o...
Page 43: 3.1.4
Options and upgrades reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 3-5 st.Re.E10233.1 table 3.3: e8030 and e8090 enabled software options option description availability e8030 e8090 m2/es02/vbi advanced vbi 3 3 m2/es02/pu performance upgrade 3 3 m2/es02/data rs-232 and rs-485 data...
Page 44: 3.2
Options and upgrades page 3-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 3.2 audio daughter card option (en8000/hdc/aud) 3.2.1 overview the additional audio option daughter is fitted to the ice card and does not have a direct external interface. The card can take its ...
Page 45: 3.3
Options and upgrades reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 3-7 st.Re.E10233.1 3.3 dual ip/ethernet output card (en8000/hwo/iptsdual) 3.3.1 overview the dual ip/ethernet output card provides two 100/1000baset ethernet ports to allow direct connection to a redundant ip/ether...
Page 46: 3.3.3
Options and upgrades page 3-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 3.3.3 dual ip output overview overview this allows direct connection to a redundant ip/ethernet network as it has two separate ethernet connections. The menu structure is shown in figure 3.3 . Th...
Page 47: 3.3.4
Options and upgrades reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 3-9 st.Re.E10233.1 3.3.4 dual ipnic control the dual ipnic control menu specifies the parameters associated with the card such as the ip address of the ports (see table 3.6 for details). Table 3.6: dual ipnic contr...
Page 48: 3.3.5
Options and upgrades page 3-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 3.3.5 ip streamer output ip streamer output: there is a menu associated with each transport stream output (see table 3.7 for details). Table 3.7: ip streamer option descriptions selected item op...
Page 49: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 4-1 st.Re.E10233.1 chapter 4 4. Operating the equipment locally contents 4.1 local control ..................................................... 4-3 4.1.1 read this first! ..................................... 4-3 4.1.2 introduction .....
Page 50
Operating the equipment locally page 4-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 51: 4.1
Operating the equipment locally reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 4-3 st.Re.E10233.1 4.1 local control 4.1.1 read this first! This reference guide has been written to give emphasis to control through the webpages. Chapter 5 explains each of the options available. 4.1.2...
Page 52: 4.2 A(Udio)/v(Ideo) Menu
Operating the equipment locally page 4-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 for text or numeric entry the character list for text entry contains the following characters: space abcdefghijklmnopqrstuvwxyzabcdefghijklmnopqrstuvwxyz 0123456789/+-=.,:;_!$%^&*(){}[...
Page 53: 4.5
Operating the equipment locally reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 4-5 st.Re.E10233.1 4.5 front panel set up password the set up menus (described in chapter 5) can be accessed via the front panel. The menu can be protected by a password. This facility is found in the ad...
Page 54
Operating the equipment locally page 4-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 55: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-1 st.Re.E10233.1 chapter 5 5. Web browser interface contents 5.1 introduction ....................................................... 5-3 5.2 how to set-up the web browser interface ........ 5-3 5.3 web browser interface options .......
Page 56
Web browser interface page 5-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 list of figures figure 5.1: internet options dialog box ................................ 5-3 figure 5.2: settings dialog box............................................. 5-4 figure 5.3: connecti...
Page 57: 5.1 Introduction
Web browser interface reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-3 st.Re.E10233.1 5.1 introduction there is a range of configuration, diagnostic and other utilities that can be accessed via a web browser, such as mozilla firefox or microsoft internet explorer. Before these pa...
Page 58
Web browser interface page 5-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 figure 5.2: settings dialog box 4. For check for newer versions of stored pages, select every visit to the page or any changes made to the pages will not be displayed. Click ok to save the chang...
Page 59
Web browser interface reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-5 st.Re.E10233.1 figure 5.4: local area network (lan) settings dialog box 7. Click advanced to open the proxy settings dialog box (see figure 5.5). Figure 5.5: proxy settings dialog box 8. In the exceptions area...
Page 60
Web browser interface page 5-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 for internet explorer version 6 the same selections must be made, but the process starts from the view menu. Once explorer has been set up, type the ip address of the encoder to be accessed in t...
Page 61: 5.3
Web browser interface reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-7 st.Re.E10233.1 5.3 web browser interface options the web browser gives access to all functions available on the front panel. Status information is always displayed on the left panel along with a picture showin...
Page 62
Web browser interface page 5-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 • stored configs load config: gives a list of preconfigured settings. Save config: saves the current setting to an existing prenamed configuration. • save / load save configuration to file: this...
Page 63: 5.4
Web browser interface — using the browser reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-9 st.Re.E10233.1 5.4 using the browser 5.4.1 layout of webpage elements figure 5.7 illustrates the elements of the webpage. Note… additional parameters may be displayed depending upon which o...
Page 64: 5.4.2 Content
Web browser interface — using the browser page 5-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.4.2 content area the user interface makes extensive use of dialog box elements. The layout and content of a particular dialog box may vary according to selections made els...
Page 65: 5.5 Configure
Web browser interface — configure webpage reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-11 st.Re.E10233.1 5.5 configure webpage the configure webpage gives access to all the menus required to set up the encoder. Figure 5.9 shows the items under the configure tab. Path: / configu...
Page 66: 5.6.2 System
Web browser interface — system menu page 5-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.6.2 system menu hierarchy figure 5.11 shows the grouping of items under each webpage. In general, the front panel menus described in chapter 4 follow the structure shown. Figure...
Page 67: 5.6.3
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-13 st.Re.E10233.1 5.6.3 system / encapsulation this is set to h.264/avc video/audio over ts. 5.6.4 system / service info menu (output = ts, syntax = atsc 2 ) the system information table provides o...
Page 68: 5.6.5
Web browser interface — system menu page 5-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.1: atsc system information option descriptions (continued) selected item options description program paradigm: this option determines whether pid values are assigned in ac...
Page 69
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-15 st.Re.E10233.1 table 5.2: dvb system information option descriptions (continued) selected item options description network id: specifies the network identity. Range: 0 to 65535 the information i...
Page 70: 5.6.6
Web browser interface — system menu page 5-16 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.6.6 system / multiple services this menu item allows the elementary streams to be divided across several services and can be used to create audio only services. Path: / configur...
Page 71: 5.6.7
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-17 st.Re.E10233.1 5.6.7 system / remote control the encoder is controlled remotely via ethernet using a web browser. Path: / configure / system menu / remote control table 5.4 describes the remote ...
Page 72: 5.6.8
Web browser interface — system menu page 5-18 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.6.8 system / general menu the general menu provides options for configuring the general parameters of the encoder such as the time and date, screen savers, and fan control. Gene...
Page 73
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-19 st.Re.E10233.1 table 5.5: general menu option descriptions (continued) selected item options description local date: displays the local date on the encoder and cannot be changed. Note … this dat...
Page 74: 5.6.9
Web browser interface — system menu page 5-20 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.6.9 system / time & date menu this menu is used to set the internal time and date for the encoder. This time and date are used for the logging of information and alarms and are ...
Page 75: 5.6.10
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-21 st.Re.E10233.1 5.6.10 system / advanced menu the advanced menu is selected from the system menu. This menu provides options for the advanced parameters of the encoder. See figure 5.14 for the ad...
Page 76: 5.6.11
Web browser interface — system menu page 5-22 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.6.11 system / dig. Program insertion (dpi) splicing is used to insert a digital program (e.G. Advertisements) into an mpeg-2 transport stream. Scte-35 has been written to suppor...
Page 77: 5.6.12
Web browser interface — system menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-23 st.Re.E10233.1 5.6.12 system / build menu the build menu is selected from the system menu . The build menu shows the version numbers of different modules within the system. They cannot be change...
Page 78: 5.7 Video
Web browser interface — video menu page 5-24 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.7 video menu 5.7.1 introduction the video menu is selected from the setup menu . This menu permits the selection of video parameters. Figure 5.17 and table 5.9 show the options a...
Page 79: 5.7.3
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-25 st.Re.E10233.1 5.7.3 video / hd video source menu table 5.9 describes the hd video source menu items, which permit the selection of video source parameters when operating in the high definition v...
Page 80
Web browser interface — video menu page 5-26 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.9: hd video source option descriptions (continued) selected item options description off noise reduction off. Adaptive 1 use noise reduction if necessary but don’t introduc...
Page 81: 5.7.4
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-27 st.Re.E10233.1 5.7.4 video / sd video source menu table 5.10 describes the sd video source menu items that permit the selection of video source parameters when operating in the standard definitio...
Page 82
Web browser interface — video menu page 5-28 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.10: sd video source option descriptions (continued) selected item options description freeze frame the last video frame received is encoded if the video input is lost. Blac...
Page 83: 5.7.5
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-29 st.Re.E10233.1 table 5.10: sd video source option descriptions (continued) selected item options description pal-b/g/h/i pal-b/g/h/i composite video input on comp video connector. Pal-m pal-m com...
Page 84
Web browser interface — video menu page 5-30 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.11: h.264/avc encoder option descriptions (continued) selected item options description bitrate: defines the maximum bitrate generated by the video encoding module. This ca...
Page 85: 5.7.6
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-31 st.Re.E10233.1 table 5.11: h.264/avc encoder option descriptions (continued) selected item options description main profile @ level 3 standard definition operation main profile @ level 4 high def...
Page 86
Web browser interface — video menu page 5-32 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 this menu permits the selection of picture-in-picture video encoding parameters. They are listed alphabetically to help with retrieving the information. Path: / configure / video m...
Page 87
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-33 st.Re.E10233.1 table 5.12: pip encoder option descriptions (continued) selected item options description original: controls the setting of the original flag in the bitstream. If set to on the bit...
Page 88
Web browser interface — video menu page 5-34 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.12: pip encoder option descriptions (continued) selected item options description 30% - 100% 100% means that the encoder attempts to reach maximum quality while not exceedi...
Page 89: 5.7.7
Web browser interface — video menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-35 st.Re.E10233.1 5.7.7 vertical blanking interval (vbi) menu table 5.13 describes vbi menu as selected from the video menu . This menu permits the selection of vertical blanking interval (vbi) para...
Page 90
Web browser interface — video menu page 5-36 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.13: vbi option descriptions (continued) selected item options description frame rate = 29.97 hz off vbi data is not extracted from the line. Vertical interval time code vit...
Page 91: 5.8 Audio
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-37 st.Re.E10233.1 5.8 audio menu 5.8.1 top-level menu figure 5.18 and the following sectionsshow the distribution of options for each coding standard. Use these as a guide to the information in this...
Page 92: 5.8.3 Advanced
Web browser interface — audio menu page 5-38 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.14: audio control options selected item options description sd-sdi sd embedded audio source hd-sdi defines the video input that contains the embedded audio content if embed...
Page 93
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-39 st.Re.E10233.1 advanced audio webpage options table 5.15 lists the advanced audio options and associated descriptions in the order they appear on the webpage. Table 5.15: advanced audio webpage o...
Page 94
Web browser interface — audio menu page 5-40 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.15: advanced audio webpage option descriptions (continued) selected item options description pid: this option sets the pid to be used for the audio channel. In the event of...
Page 95
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-41 st.Re.E10233.1 table 5.15: advanced audio webpage option descriptions (continued) selected item options description codec pack: specifies the unique version of the complete code block used on thi...
Page 96: 5.8.4
Web browser interface — audio menu page 5-42 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.8.4 audio a/b menu audio a/b menu structure figure 5.21 shows the audio menu options generally in the order they appear on the webpage. Figure 5.21: menu hierarchy – configure/au...
Page 97
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-43 st.Re.E10233.1 coding standard associated options figure 5.21 shows the audio menu options generally in the order they appear on the webpage. Table 5.16 shows the options available for each stand...
Page 98
Web browser interface — audio menu page 5-44 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.16: coding standard associated options (continued) coding standard comments option dolby digi tal pass- thru mpeg layer 2 dolby digi tal op digital loss 3 3 3 original 3 3 ...
Page 99
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-45 st.Re.E10233.1 table 5.17: audio a/b option descriptions (continued) selected item options description off off (min delay) on (avc 1) on (avc 2) auto lip sync: this option controls whether the en...
Page 100
Web browser interface — audio menu page 5-46 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.17: audio a/b option descriptions (continued) selected item options description mpeg layer 2 to meet the mpeg layer 2 audio encoding algorithm specification, the audio must...
Page 101
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-47 st.Re.E10233.1 table 5.17: audio a/b option descriptions (continued) selected item options description impedance: it enables the input impedance of the analogue audio input to be set to either 60...
Page 102
Web browser interface — audio menu page 5-48 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 5.17: audio a/b option descriptions (continued) selected item options description 32 khz sets the sampling frequency to 32 khz. 48 khz sets the sampling frequency to 48 khz s...
Page 103
Web browser interface — audio menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-49 st.Re.E10233.1 table 5.18: audio bitrate options available settings mpeg layer 2 coding dolby digital mono dual m ono stereo joint stereo 1/0(c) 2/0(l,r) 32 kbit/s 48 kbit/s 56 kbit/s 64 kbit/s 8...
Page 104: 5.9 Data
Web browser interface — data menu page 5-50 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.9 data menu 5.9.1 overview the data menu is selected from the setup menu . This menu permits the selection of rs-232 asynchronous data and rs-422 synchronous data channel paramete...
Page 105
Web browser interface — data menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-51 st.Re.E10233.1 table 5.19: data a, rs232 option descriptions (continued) selected item options description on(motorola) if on (motorola) is selected, the stream is identified in the pmt as a compo...
Page 106: 5.9.3
Web browser interface — data menu page 5-52 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.9.3 data b - rs422 menu table 5.20shows the data b, rs422 options. Table 5.20: data b, rs422 options selected item options description encoding: switches the rs-422 synchronous da...
Page 107: 5.10 Mux
Web browser interface — mux menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-53 st.Re.E10233.1 5.10 mux menu access the mux menu from the configure menu . This menu permits the selection of multiplexer output parameters. Path: / configure / mux figure 5.23: configure> mux webp...
Page 108
Web browser interface — mux menu page 5-54 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 selected item options description local oscillator the system clock is derived from the local oscillator. Hsync (external) the system clock is locked to the hsync input. Video the sy...
Page 109: 5.11 Output
Web browser interface — output selection reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-55 st.Re.E10233.1 5.11 output selection 5.11.1 overview figure 5.24 shows the output selection options for the en80x0 encoder. Path: / configure / output figure 5.24: output selection items 5....
Page 110: 5.11.3 Ice-3
Web browser interface — output selection page 5-56 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.11.3 ice-3 status displays the software and fpga versions of the modules which make up the hd intelligent compression engine. Figure 5.25: typical ice-3 display note… some ...
Page 111: 5.11.5 Delivery
Web browser interface — output selection reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-57 st.Re.E10233.1 5.11.5 delivery descriptor overview the screens in this menu vary according to the descriptor type selected. Table 5.22: descriptor type options selected option description c...
Page 112
Web browser interface — output selection page 5-58 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 descriptor type = cable table 5.24 shows the options for the cable descriptor type table 5.24: cable descriptor type options selected item options description min: 0.000 mhz ...
Page 113: 5.12
Web browser interface — stored configuration tab reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-59 st.Re.E10233.1 5.12 stored configurations tab 5.12.1 overview the encoder has a set of 16 default configurations for both 525 and 625 line standards. These configurations provide th...
Page 114: 5.12.2
Web browser interface — stored configuration tab page 5-60 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 5.12.2 load config n (from flash memory) option this options loads the parameters from one of the configuration files into the operational set for the encoder. Figure...
Page 115: 5.14 Fault
Web browser interface — output selection menu reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 5-61 st.Re.E10233.1 figure 5.29: save/load configurations 5.14 fault reporting there is significant information that can be extracted from the menu system on the encoder that should be incl...
Page 116
Web browser interface — output selection menu page 5-62 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 117: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 6-1 st.Re.E10233.1 chapter 6 6. Picture in picture contents 6.1 introduction ....................................................... 6-3 6.2 setting up pip on the en8000 encoder ............ 6-3 6.2.1 allocate streams to a service........
Page 118
Picture in picture page 6-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 119: 6.1 Introduction
Picture in picture reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 6-3 st.Re.E10233.1 6.1 introduction picture in picture (pip) functionality is only available in the encoder after the purchase of the en8000/swo/pip license (please refer to customer services for details). When pip i...
Page 120: 6.2.3
Picture in picture page 6-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table 6.2: resolutions and bitrates resolution (v x h) min bitrate max bitrate available from selected input 720 x 576 (50 hz) 720 x 480 (60hz) 256 kbit/s 10 mbit/s hd 704 x 576 (50 hz) 704 x 480 (...
Page 121: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-1 st.Re.E10233.1 chapter 7 7. Preventive maintenance and fault- finding contents 7.1 introduction ....................................................... 7-3 7.2 preventive maintenance.................................... 7-3 7.2.1 ro...
Page 122
Preventive maintenance and fault-finding page 7-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 123: 7.1 Introduction
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-3 st.Re.E10233.1 7.1 introduction this chapter provides the schedules and instructions, where applicable, for routine inspection, cleaning and maintenance of the equipment that should be perfo...
Page 124: 7.3
Preventive maintenance and fault-finding page 7-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 checks on completion of servicing upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product ...
Page 125: 7.4
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-5 st.Re.E10233.1 7.4 front panel display errors and diagnostics menus figure 7.1: errors and diagnostic menu tree 7.4.1 display errors option it is possible to enable or disable the display of...
Page 126: 7.4.4 Diagnostics
Preventive maintenance and fault-finding page 7-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 caution… it does not mean that the encoder is fully functional if the error option does not produce any results. Some processes cannot be tested on-line. Note… this function c...
Page 127: 7.5
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-7 st.Re.E10233.1 7.5 web browser support 7.5.1 support tabbed page figure 7.2 shows the items available on the support tabbed page available through the web browser. Use this page to interroga...
Page 128: 7.5.3 Alarms
Preventive maintenance and fault-finding page 7-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 7.5.3 alarms page this page displays all the possible alarms and allows the user to set the level of each alarm. A list of alarms is given in annex l. Figure 7.4: typical alar...
Page 129: 7.6 Fault-Finding
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-9 st.Re.E10233.1 7.6 fault-finding 7.6.1 fault-finding philosophy it is the objective of this chapter to provide sufficient information to enable the operator to rectify apparent faults or els...
Page 130: 7.6.3
Preventive maintenance and fault-finding page 7-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 7.6.3 a.C. User accessible fuse replacement a fuse is held in an integral fuse carrier at the a.C. Power inlet at the rear panel. Note… refer to annex b, technical specificat...
Page 131: 7.6.5 Video
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-11 st.Re.E10233.1 to replace the d.C. Power fuse: 1. Ensure that d.C. Power is turned off or the power cable is disconnected from the power inlet. 2. Unscrew the fuse carrier and remove the ol...
Page 132: 7.7
Preventive maintenance and fault-finding page 7-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 7.7 power supply problems/green led on front panel unlit 7.7.1 symptoms warning... Do not attempt to service the power supply unit as opening or removing covers may expose da...
Page 133: 7.8
Preventive maintenance and fault-finding reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page 7-13 st.Re.E10233.1 table 7.4: fans not working/overheating step action if result of action is yes… if result of action is no… 1 check fan rotation. Inspect the fans located at the sides of the ...
Page 134
Preventive maintenance and fault-finding page 7-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 135
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-1 st.Re.E10233.1 annex a a. Glossary the following list covers most of the abbreviations, acronyms and terms as used in tandberg television limited manuals, user and reference guides. All terms may not be included in this reference g...
Page 136
Glossary page a-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 amol i and ii automatic measure of line-ups i and ii: used by automated equipment to measure programme-viewing ratings. Arib association of radio industries and businesses is a japanese organisation for the ...
Page 137
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-3 st.Re.E10233.1 bw bandwidth: the transmission capacity of an electronic line such as (among others) a communications network, computer bus, or broadcast link. It is expressed in bits per second, bytes per second or in hert...
Page 138
Glossary page a-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 compression reduction in the number of bits used to represent the same information. For the purposes of a broadcast system, it is the process of reducing digital picture information by discarding redundant p...
Page 139
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-5 st.Re.E10233.1 downconvert the process by which the frequency of a broadcast transport stream is shifted to a lower frequency range. Dpcm differential pulse code modulation: an audio digitisation technique that codes the d...
Page 140
Glossary page a-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 epg electronic programme guide: on-screen programme listing using thumbnail pictures and/or text. Ethernet the most widely used local area network (lan) defined by the ieee as the 802.3 standard. Transmissio...
Page 141
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-7 st.Re.E10233.1 ice intelligent compression engine: the module on which the advanced coding of video and audio is performed. Idu independent data unit that is a portion of elementary stream that can be decoded independently...
Page 142
Glossary page a-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 itu-t international telecommunications union - telecommunications standardisation sector (was ccitt). Jpeg joint photographic experts group: iso/itu standard for compressing still images. It has a high compr...
Page 143
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-9 st.Re.E10233.1 mmds multichannel microwave distribution system: a terrestrial microwave direct-to-home broadcast transmission system. Motion compensation the use of motion vectors to improve the efficiency of the predictio...
Page 144
Glossary page a-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 nm nanometre: a unit of length equal to one thousand millionth (10 -9 ) of a metre. Ntsc national television systems committee: the group, which developed analogue standards used in television broadcast sys...
Page 145
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-11 st.Re.E10233.1 pin personal identification number: a password used to control access to programming and to set purchase limits. Each subscriber household can activate several pins and may use them to set individual parent...
Page 146
Glossary page a-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 qsif quarter screen image format. Quantise a process of converting analogue waveforms to digital information. 8-bit quantisation as set out in itu-r rec. 601. Uses 256 levels in the range 0 – 255 to determi...
Page 147
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-13 st.Re.E10233.1 si service information: digital information describing the delivery system, content and scheduling (timing) of broadcast data streams. Dvb-si data provides information to enable the ird to automatically dem...
Page 148
Glossary page a-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 transport stream a set of packetised elementary data streams and si streams, which may comprise more than one programme, but with common synchronisation and error protection. The data structure is defined i...
Page 149
Glossary reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page a-15 st.Re.E10233.1 xilinx a type of programmable integrated circuit. Y (luminance) defines the brightness of a particular point on a tv line. The only signal required for black and white pictures..
Page 150
Glossary page a-16 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 151: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-1 st.Re.E10233.1 annex b b. Technical specification contents b.1 inputs ...............................................................B-3 b.1.1 video......................................................B-3 hd-sdi (en8090 only) .......
Page 152
Technical specification page b-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table b.11: embedded audio specification ..........................B-9 table b.12: embedded audio specification ..........................B-9 table b.13: mpeg-2 aac audio encoding bitrates ......
Page 153: B.1 Inputs
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-3 st.Re.E10233.1 b.1 inputs b.1.1 video hd-sdi (en8090 only) table b.1: high definition serial digital video specification item specification safety status selv connector designation hd sdi in connector type 7...
Page 154
Technical specification page b-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 h sync table b.3: h sync specification item specification safety status selv connector designation h sync connector type 75 Ω bnc female socket input standard 625-line pal, 525-line pal-m or 5...
Page 155
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-5 st.Re.E10233.1 international television standards table b.5 shows television standards appropriate to the encoder. Table b.5: international television standards as indicated in menus m m b g h i d region usa...
Page 156
Technical specification page b-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table b.8: progressive coding resolutions (sd) 625 line modes 525 line modes 720 pixels x 576 lines 720 pixels x 480 lines 704 pixels x 576 lines 704 pixels x 480 lines 640 pixels x 576 lines ...
Page 157: B.1.2 Audio
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-7 st.Re.E10233.1 b.1.2 audio analogue and digital audio table b.9: analogue and digital audio specification item specification safety status selv connector designation audio in connector type 15-way, d-type ma...
Page 158
Technical specification page b-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table b.10: musicam (mpeg 1 layer 2) analogue test specification item specification set up of alteia receiver audio format mpeg output analogue clip level 18 db set up of audio encoder input a...
Page 159
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-9 st.Re.E10233.1 table b.10: musicam (mpeg 1 layer 2) analogue test specification (continued) item specification phase @ 0 dbs z 40 hz ±2° 100 hz ±2° 315 hz ±2° 1 khz ±2° 6.3 khz ±2° 10 khz ±2° 15 khz ±2° embe...
Page 160
Technical specification page b-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 mpeg-4 he-aac encoding bitrates table b.14: mpeg-4 he-aac audio encoding bitrates bitrate (kbit/s) stereo dual-mono 64 3 3 80 3 3 96 3 3 128 3 3 mpeg-4 he-aac v2 encoding bitrates table b.15:...
Page 161: B.1.3 Rs-232
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-11 st.Re.E10233.1 dolby digital audio encoding bitrates table b.17: dolby digital audio encoding bitrates bitrate (kbit/s) single channel mono (1/0) dual channel stereo (2/0) 56 3 3 64 3 3 80 3 3 96 3 3 112 3 ...
Page 162: B.1.4 Rs-422
Technical specification page b-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 b.1.4 rs-422 data this provides an rs-422 synchronous, serial communications data input interface. Table b.19: rs-422 data specification item specification safety status selv type itu-t v.11 ...
Page 163: B.2 Asi
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-13 st.Re.E10233.1 b.2 asi outputs table b.22: asi out specification item specification standard cenelec en50083-9: 2002 safety status selv connector type bnc 75 Ω connector designation asi out 1, asi out 2, as...
Page 164: B.4 Power
Technical specification page b-14 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 b.4 power supply b.4.1 a.C. Mains input this equipment is fitted with an wide-ranging power supply. It is suitable for supply voltages of 100-120 vac -10% +6% or 220-240 vac -10% +6% at 50/60...
Page 165: B.4.2
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-15 st.Re.E10233.1 b.4.2 d.C. Supply input (-48 vdc version) notes... 1. Only model en8030/bas/48v and en8090/bas/48v use a d.C. Power supply. 2. Ensure correct polarity is maintained. 3. The unit must have a p...
Page 166: B.6 Environmental
Technical specification page b-16 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 b.6 environmental conditions table b.28: environmental specification item specification operational temperature -10 ° c to +50 ° c (14 ° f to 122 ° f) ambient with free air-flow over temperat...
Page 167: B.7.2 Emc
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-17 st.Re.E10233.1 b.7.2 emc 2 the equipment has been designed and tested to meet the following: en 55022 and cispr22 european international emission standard limits and methods of measurement of radio frequenc...
Page 168: B.7.5 Packaging
Technical specification page b-18 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 b.7.5 packaging statement the outer carton and any cardboard inserts are made from 82% recycled material and are fully recyclable. The stratocell™ or ethafoam 220™ polyethylene foam inserts c...
Page 169: B.7.7 Materials
Technical specification reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page b-19 st.Re.E10233.1 b.7.7 materials declarations tandberg television products are designed and manufactured in keeping with good environmental practise. Our component and materials selection policy prohibits the...
Page 170: B.7.9 Recycling
Technical specification page b-20 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 b.7.9 recycling tandberg television provides assistance to customers and recyclers through our web site http://www.Tandbergtv.Com/productrecycling.Ink please contact tandberg television’s cus...
Page 171
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page c-1 st.Re.E10233.1 annex c c. Language abbreviations languages are shown in alphabetical order. Language abbreviation danish dan dutch dut english eng finnish fin french fre german ger italian ita norwegian nor portugese por spanish sp...
Page 172
Language abbreviations page c-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 173: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-1 st.Re.E10233.1 annex d d. Creating and downloading a logo contents d.1 introduction ...................................................... D-3 d.2 summary of features....................................... D-3 d.3 osd programs buil...
Page 174
Creating and downloading a logo page d-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 175: D.1 Introduction
Creating and downloading a logo reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-3 st.Re.E10233.1 d.1 introduction the encoder includes a logo overlay facility whereby an image can be overlaid onto the active video prior to encoding. This enables broadcasters to trademark or brand ...
Page 176
Creating and downloading a logo page d-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 figure d.1: web browser interface the dialogue box, see figure d.2 , will be displayed. Figure d.2: file download dialogue box clicking on option open this file from its current locati...
Page 177: D.4
Creating and downloading a logo reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-5 st.Re.E10233.1 figure d.3: files for osd creator and loader d.4 creating a logo using osd creator osd creator ( creator.Exe ) is an application for creating logo files (.Osd format) for use with the ...
Page 178: D.5.2
Creating and downloading a logo page d-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 figure d.4: osd creator screen showing example logo d.5.2 loading a .Bmp file select file/open from the menu, and choose a file with a .Bmp extension. The image is displayed in its own...
Page 179
Creating and downloading a logo reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-7 st.Re.E10233.1 osd creator uses a colour palette with a maximum of 256 entries. Each pixel in the image is mapped to an entry in the palette, which holds a value for the red, green and blue and trans...
Page 180: D.5.4 Downsampling
Creating and downloading a logo page d-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 editing the palette the palette may be displayed alongside the image by clicking the show/hide palette toolbar button. The transparency of each palette entry may be altered in the same...
Page 181: D.6
Creating and downloading a logo reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-9 st.Re.E10233.1 d.6 downloading a logo using osd loader the osd loader application (osd.Exe) is used for downloading logo (.Osd) files to the encoder and controlling which are displayed. The applicati...
Page 182: D.7.2
Creating and downloading a logo page d-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 table d.1: resolution modes resolution mode video standard 576 standard definition 625 line 480 standard definition 525 line 480p not supported 576p not supported 720p not supported 1...
Page 183
Creating and downloading a logo reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page d-11 st.Re.E10233.1 576 lines 1 720 720 pixels digital active picture 702 pixels analogue active picture pixel 1 2 line field 23 336 337 338 24 25 623 310 osd loader co-ordinates (858,619) osd loader co-...
Page 184: D.7.3
Creating and downloading a logo page d-12 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 d.7.3 show and hide regions the download button defines a region in the encoder, which remains until the encoder is turned off, the remove button is clicked, or the region is download...
Page 185: Contents
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page e-1 st.Re.E10233.1 annex e e. Audio modes contents e.1 a brief introduction to coding standards ..........E-3 e.1.1 mpeg standards ...................................E-3 background............................................E-3 mpeg-1 ...
Page 186
Audio modes page e-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.
Page 187: E.1
Audio modes reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page e-3 st.Re.E10233.1 e.1 a brief introduction to coding standards where appropriate, the output transport stream can be made compliant with atsc a53(e) atsc digital television standard and dvb 101-154 v1.7.7. E.1.1 mpeg stand...
Page 188: E.1.2 Mpeg-4
Audio modes page e-4 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 mpeg-4 he aac this standard builds on the mpeg-2 aac. Some of the existing tools have been improved and new ones added. All aac objects (including the error robust modes) contain the perceptual noise subs...
Page 189: E.2
Audio modes reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page e-5 st.Re.E10233.1 dolby recommends stereo signals may be coded at 192 kbit/s, and 5.1 at 448 kbit/s, but other rates are available if required. E.2 audio coding modes e.2.1 mono this mode has a single audio channel that is...
Page 190: E.3.1 Analogue
Audio modes page e-6 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 e.3.1 analogue audio on the encoder there are two channels of analogue audio available. Figure e.2 shows the coding methods that may be used with the analogue audio inputs. Analogue audio adc linear pcm s...
Page 191: E.3.2 Digital
Audio modes reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page e-7 st.Re.E10233.1 e.3.2 digital audio on the encoder there are two input channels of audio available. When a digital audio source is used, consideration must be given to the choice of clock source used by the encoder. To e...
Page 192
Audio modes page e-8 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 digital audio ae s/ebu) pre - encoded bit - stream linear pcm sa aa internal coding mpeg - 1 layer ii he aac internal coding sa synchronised audio aac figure e.3: digital / sdi embedded audio route serial...
Page 193
Audio modes reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page e-9 st.Re.E10233.1 audio groups take n from sdi group 1 group 3 group 2 group 4 4:1 dembedder 1 sdi embedded 1 sdi embedded 2 group 1 group 3 group 2 group 4 4:1 user did selection default 0x1fd) dembedder 2 sdi embedded 3 ...
Page 194: E.4 Summary
Audio modes page e-10 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 hd sdi input selection there are 8 audio de-embedders in the hd-sdi module. Each can de-embedded one aes/ebu stream that contains 2 audio streams, left and right or dolby digital pre-encoded stream. The ...
Page 195
Reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders page f-1 st.Re.E10233.1 annex f f. Accuracy of frequency sources this equipment is based around iso/iec 13818 specifications (commonly known as mpeg-2) and within these specifications all timing is derived from a 27 mhz system clock. The sy...
Page 196
Accuracy of frequency sources page f-2 reference guide: en8000 mpeg-4 part 10 (h.264/avc) encoders st.Re.E10233.1 blank.