TANDBERG GW Dataport Command Interface D13202 User Manual
Summary of GW Dataport Command Interface D13202
Page 1
This document is not to be reproduced in whole or in part without the permission in writing from: tandberg tandberg gw dataport command interface user guide software version g1.0 tandberg d13202 rev 01.
Page 2: Table Of Contents
Tandberg gw dataport command interface user guide d13202 rev 01 2 table of contents 1. Introduction .......................................................................................................................... 3 2. Connecting to the dataport command interface through the rs- 232 port. ....
Page 3
Tandberg gw dataport command interface user guide d13202 rev 01 3 1. Introduction the tandberg gw dataport command interface user guide contains guidelines on how to use the textual command interface supported by the gw. The dataport command interface can be accessed through telnet via the lan inter...
Page 4
Tandberg gw dataport command interface user guide d13202 rev 01 4 2. Connecting to the dataport command interface through the rs-232 port. The rs-232 port is a 9-pin, female, d-sub connector located on the back of the gw. The port is configured as a dce (data communications equipment). The rs-232 po...
Page 5
Tandberg gw dataport command interface user guide d13202 rev 01 5 2.2. Configuring the dataport from the web interface click on system configuration tab and then the dataport button. The dataport can be configured by setting baudrate, parity, databits and stopbits. 2.3. Troubleshooting if communicat...
Page 6
Tandberg gw dataport command interface user guide d13202 rev 01 6 3. Connecting to the datport command interface using telnet the tandberg gw has two lan ports. Connection to the dataport command interface via telnet should be done through lan port 1. The gw’s telnet server provides access to the da...
Page 7
Tandberg gw dataport command interface user guide d13202 rev 01 7 4. The tandberg gw commands 4.1. Introduction typing ‘ ? ’ or ‘ help ’ when connected to the dataport command interface will return a list of valid commands. The commands are used to control the functions of the gw. A command may be f...
Page 8
Tandberg gw dataport command interface user guide d13202 rev 01 8 case where the user is trying to transfer a call from an inactive gw port (the user input is shown in bold). Calltransfer 1 999999 *r invalid gateway id error parameter setting commands are commands that set a system parameter to a sp...
Page 9
Tandberg gw dataport command interface user guide d13202 rev 01 9 4.2.1. System configuration commands command: description: defvalues set this command is used to restore factory default settings. Issuing this command with no parameters will restore all settings except network settings and option ke...
Page 10
Tandberg gw dataport command interface user guide d13202 rev 01 10 example of ipaddress feedback: *p ipaddress 1 static 10.0.5.98 *p ipaddress 1 subnetmask 255.255.0.0 *p ipaddress 1 gateway 10.0.0.1 ipassignment selects between dhcp (dynamic host configuration protocol) or static ip address allocat...
Page 11
Tandberg gw dataport command interface user guide d13202 rev 01 11 best available setting. Example of ipspeed feedback: *p ipspeed 1 auto ipqos configures the different quality of service (qos) algorithms supported by the tandberg gw. Qos are used to set priority on qos enabled ip networks. Ipqos pr...
Page 12
Tandberg gw dataport command interface user guide d13202 rev 01 12 example of ipqos feedback: *p ipqos prectlph audio auto *p ipqos diffstlph audio 0 *p ipqos precvtlph audio auto *p ipqos precvtlph signalling auto *p ipqos precvtlph video auto *p ipqos precvtlph data auto *p ipqos diffsvtlph audio ...
Page 13
Tandberg gw dataport command interface user guide d13202 rev 01 13 --- parameters: • profile number: p1/p2/p3/p4/p5/p6 . The gw can hold as many as six profiles ( p1 , p2 and p3 are predefined and can not be changed). • call prefix: the prefix number for this profile. • profile name: the profile’s n...
Page 14
Tandberg gw dataport command interface user guide d13202 rev 01 14 prichan low or prichan high or prichan search --- parameters: • pri interface: a/b/c/d. Letters identifying the different pri interfaces. O a : pri interface 1 o b : pri interface 2 o c : pri interface 3 o d : pri interface 4 sub-com...
Page 15
Tandberg gw dataport command interface user guide d13202 rev 01 15 o euro - euro isdn example of prinet feedback: *p prinet att prinumbrange defines the pri number range for the various pri interfaces. Prinumbrange --- parameters: • pri interface: a/b/c/d. Letters identifying the different pri inter...
Page 16
Tandberg gw dataport command interface user guide d13202 rev 01 16 *p services http on *p services https on *p services snmp on *p services ftp on sendnum enables/disables broadcast of the local unit’s number during h.320 call setup. Note! The transfer of the local number to a remote system or the p...
Page 17
Tandberg gw dataport command interface user guide d13202 rev 01 17 example of sport feedback: *p sport 9600 n 8 1 systemname sets the gw name. Systemname --- parameters: • name: textstring of maximum 16 characters. Example of systemname feedback: *p systemname tandberg.
Page 18
Tandberg gw dataport command interface user guide d13202 rev 01 18 4.2.2. General gw commands command: description: calltransfer disconnects the h323 terminal of a gw call and reconnects to another h323 terminal, by either specifying a telephone number or by referring to a directory entry. Calltrans...
Page 19
Tandberg gw dataport command interface user guide d13202 rev 01 19 disc --- parameters: • gwid: 1..16. Identifier referring to a gw call. Gwdid sets isdn did (direct inwards dialling) parameters. When did is enabled the gw will strip of the last digits in the isdn incoming number and use this extrac...
Page 20
Tandberg gw dataport command interface user guide d13202 rev 01 20 gwh323service servprefix or gwh323service maxbw or gwh323service isdncallprefix or gwh323service restrict or gwh323service description parameters: • id: 1..20. Identificator referring to a specific h323service. • bw: 64/128/192/256/3...
Page 21
Tandberg gw dataport command interface user guide d13202 rev 01 21 or gwsettings duovideo or gwsettings encryption sub-commands: • natvid : sets natural video support to on or off. • customformats : sets custom format support to on or off • duovideo : sets duovideo support to on or off • encryption ...
Page 22
Tandberg gw dataport command interface user guide d13202 rev 01 22 4.2.3. System status commands command: description: callhistory used to list call related information for the last 20 calls. Callhistory [logid] status format: callhistory encrypt. Stat> --- parameters: • logid: 1..20. Id referring t...
Page 23
Tandberg gw dataport command interface user guide d13202 rev 01 23 chanstat used to list channel status information for the pri interface. Chanstat [pri interface] [channel] status format: chanstat : --- parameters: • pri interface: a/b/c/d. Letters identifying the different pri interfaces. O a : pr...
Page 24
Tandberg gw dataport command interface user guide d13202 rev 01 24 • h323 callid: the call id of the h323 terminal • h323 termnumber: the number of the h323 terminal example of gwcalls feedback: *s gwcalls 1 1 22222222 2 66666666 h323gkstatus returns current gatekeeper status. H323gkstatus status fo...
Page 25
Tandberg gw dataport command interface user guide d13202 rev 01 25 off 0 ipcallstatistics returns ip dynamic information for all active ip calls. Ipcallstatistics status format: ipcallstatistics --- parameters: • callid: 1..16/32. Identifier referring to a call. • protocol: h323. • chantype: audio/v...
Page 26
Tandberg gw dataport command interface user guide d13202 rev 01 26 • pri interface: a/b/c/d. Letters identifying the different pri interfaces. O a : pri interface 1 o b : pri interface 2 o c : pri interface 3 o d : pri interface 4 • status: disabled / red alarm / blue alarm/ yellow alarm / synced / ...
Page 27
Tandberg gw dataport command interface user guide d13202 rev 01 27 • vidres: unknown / cif / qcif / sqcif / 4cif / sif / 4sif / vga / svga / xga • duores: cif / qcif / sqcif / 4cif / sif / 4sif / vga / svga / xga example of statout feedback: *s statout 1 outgoing synced norestrict h323-768 g722 h263...
Page 28
Tandberg gw dataport command interface user guide d13202 rev 01 28 4.2.4. Debug commands command: desription: eventlog the eventlog records all serious errors registered by the system. The log can be used to identify the cause for errors. The complete eventlog can be downloaded from the embedded ftp...
Page 29
Tandberg gw dataport command interface user guide d13202 rev 01 29 6 146.172.254.249 (40 ms) 7 146.172.248.5 (40 ms) 8 146.172.248.9 (40 ms) 9 146.172.248.1 (40 ms) 10 146.172.248.62 (40 ms) 11 217.70.229.33 (40 ms) 12 213.248.78.1 (40 ms) 13 213.248.66.89 (40 ms) 14 213.248.65.25 (50 ms) 15 213.248...
Page 30
Tandberg gw dataport command interface user guide d13202 rev 01 30 4.2.5. Special commands command: description: boot reboots the system. Boot dispparam lists all parameter settings. Dispparam feedback turns feedback on system changes on / off. Feedback [type] --- parameters: • type: parameter/statu...
Page 31
Tandberg gw dataport command interface user guide d13202 rev 01 31 4.3. Parameter storage parameters are set by issuing parameter setting commands, ref. Chapter 4.1.2 . All parameters and their corresponding storage type are listed in the table below. The following definitions are used: level 0: no ...
Page 32
Tandberg gw dataport command interface user guide d13202 rev 01 32 4.4. Index commands boot, 30 callhistory, 22 callstatus, 22 calltransfer, 18 chanstat, 23 defvalues set, 9 directory, 18 disc, 18 dispparam, 30 dumph221, 28 encstatus, 23 eventlog, 28 feedback, 30 gwcalls, 23 gwdid, 19 gwextdialin, 1...