TANDBERG REPLACE TAPE DRIVE IN T24 OR T48 Manual - page 25
25
OF
28
R
ECONFIGURING
THE
L
IBRARY
AND
R
ESUMING
O
PERATION
R
ECONFIGURING
THE
L
IBRARY
In order for the library to recognize the new tape drive, you must set the tape drive
configuration to match the tape drives that are installed in the library.
Note:
Do not connect the SCSI cables at this time.
To set tape drive configuration:
1.
At the Home screen, press Drive.
If necessary, enter the operator panel password (see
page 72
).
2.
Press
until the selection arrow (
) points to Drive Configuration.
3.
Press Select.
Note:
The library lists “no drive” only if there is no room for more tape drives. For
example, in the above screen, the StorageLibrary T48 library has two half height
tape drives. The four tape drive number is for four half height tape drives.
Drive
Drive ID
Drive SCSI ID
Drive Configuration
Library SCSI Bridge
Select
Back
Drive Configuration
1:
HP LTO-2 HalfHigh
2:
HP LTO-2 HalfHigh
3:
no drive
4:
no drive
Modify
OK
Summary of REPLACE TAPE DRIVE IN T24 OR T48
Page 1
Copyright 2006 tandberg data and exabyte, ez17, m2, vxa, and vxatape are registered trademarks; exabotics, mammothtape, and smartclean are trademarks; supportsuite is a service mark. Linear tape-open, lto, the lto logo, ultrium and the ultrium logo are trademarks of hp, ibm, and quantum in the us an...
Page 2
2 of 28 g eneral i nformation both the storagelibrary t24 and storagelibrary t48 library accommodate ultrium 3 (lto-3) or ultrium 2 (lto-2) tape drives in half height (hh) or full height (fh) configurations. Neither library will accommodate lto-1 tape drives. Note: most of the illustrations show scs...
Page 3
3 of 28 r eference i llustrations storagelibrary t24— ! Important be sure to use the serial cable (c) that came with your replacement kit. The serial cables are specifically configured (at the factory) for use with the individual tape drives. Lower scsi cover plate (s) upper scsi cover plate (s) sto...
Page 4
4 of 28 figure 1 storagelibrary t24 serial cable routing—full height tape drive figure 2 storagelibrary t24 serial cable routing—half height tape drives figure 3 storagelibrary t24 power cable routing—full height tape drive figure 4 storagelibrary t24 power cable routing—half height tape drives seri...
Page 5
5 of 28 storagelibrary t48— ! Important be sure to use the serial cable (c) that came with your replacement kit. The serial cables are specifically configured (at the factory) for use with the individual tape drives. Storagelibrary t48 tape drive half height scsi cover plate (s) scsi cover plate (s)...
Page 6
6 of 28 figure 5 storagelibrary t48 serial cable routing—full height tape drives figure 6 storagelibrary t48 serial cable routing—half height tape drives serial cable (c) bottom serial connector third serial connector (not used) second serial connector top serial connector (not used) drive 1 drive 2...
Page 7
7 of 28 figure 7 storagelibrary t48 power cable routing—full height tape drives figure 8 storagelibrary t48 power cable routing—half height tape drives power cable (d) library power connector top power connector (not used in this configuration) second power connector (not used in this configuration)...
Page 8
8 of 28 i nstalling a dditional t ape d rives to install an additional tape drive (or tape drives), follow these steps: 1. Preparing for replacement— a. Power off the library (press the 0 on the back of the unit) b. Disconnect the power cord, the scsi or fibre channel cable(s), and the terminator (i...
Page 9
9 of 28 a. Remove the two screws ( a ) holding the tape drive cooling plate ( b ). Remove the plate, and discard it and the screws. B. Disconnect the power cables ( d ) from all of the tape drives. 3. Installing the tape drive— a. Locate the serial cable ( c ) that came in your replacement kit and a...
Page 10
10 of 28 storagelibrary t48 library serial cable connections— full height tape drive—see figure 5 half height tape drive—see figure 6 b. While holding the cables to the side, slide the new tape drive directly into the library, leaving it a short distance out to access the cables. Use care not to dam...
Page 11
11 of 28 storagelibrary t48 tape drive serial and power cable connections— full height tape drive: serial—route the serial cable ( c ) under the tape drive carrier as shown here; connect as shown in figure 5 (storagelibrary t48 fh serial cable routing). Power—route the power cable through the tape d...
Page 12
12 of 28 storagelibrary t48 tape drive serial and power cable connections— half height tape drive: serial—route the serial cable ( c ) over the tape drive carrier as shown here; connect as shown in figure 6 (storagelibrary t48 hh serial cable routing). Power—route the power cable through the tape dr...
Page 13
13 of 28 4. Completing the installation— a. Locate the tape drive cover plate (see “reference illustrations” on page 3 ). First, remove the necessary scsi plates ( s ), then attach the tape drive cover plate ( p ) with the screws you removed earlier. B. Reconfigure your library—you must reconfigure ...
Page 14
14 of 28 r eplacing a t ape d rive ( same configuration ) to replace a tape drive with a different tape drive of the same configuration (half height to half height, or full height to full height), follow these steps. 1. Preparing for replacement— a. Power off the library (press the 0 on the back of ...
Page 15
15 of 28 3. Installing the new tape drive— a. Locate the serial cable ( c ) that came in your replacement kit and attach it to the appropriate serial connector inside the library. Storagelibrary t24 library serial cable connections— full height tape drive—see figure 1 half height tape drive—see figu...
Page 16
16 of 28 storagelibrary t24 half height tape drive serial and power cable connections— serial—route the serial cable ( c ) over the tape drive carrier and under the power cable as shown here; connect as shown in figure 2 (storagelibrary t24 hh serial cable routing). Power—route the power cable throu...
Page 17
17 of 28 storagelibrary t48 full height tape drive serial and power cable connections— serial—route the serial cable ( c ) under the tape drive carrier as shown here; connect as shown in figure 1 (storagelibrary t48 fh serial cable routing). Power—route the power cable through the tape drive carrier...
Page 18
18 of 28 storagelibrary t48 half height tape drive serial and power cable connections— serial—route the serial cable ( c ) over the tape drive carrier as shown here; connect as shown in figure 6 (storagelibrary t48 hh serial cable routing). Power—route the power cable through the tape drive carriers...
Page 19
19 of 28 r eplacing a t ape d rive (h alf height to f ull height ) to replace a half height tape drive with a full height tape drive, follow these steps. 1. Preparing for replacement— a. Power off the library (press the 0 on the back of the unit) b. Disconnect the power cord, the scsi or fibre chann...
Page 20
20 of 28 d. Remove the plate, and discard it and the screws. Note: this figure shows the storagelibrary t48 scsi library with one half height tape drive installed. Remove the storagelibrary t24 internal cooling plates the same way. E. While holding the cables out of the way, remove the tape drive(s)...
Page 21
21 of 28 3. Installing the tape drive— a. Locate the serial cable ( c ) that came in your replacement kit and attach it to the appropriate serial connector inside the library. Storagelibrary t24 library serial cable connections— full height tape drive—see figure 1 storagelibrary t48 library serial c...
Page 22
22 of 28 storagelibrary t48 full height tape drive serial and power cable connections— serial—route the serial cable ( c ) under the tape drive carrier as shown here; connect as shown in figure 1 (storagelibrary t48 fh serial cable routing). Power—route the power cable through the tape drive carrier...
Page 23
23 of 28 d. Slide the tape drive the remaining distance into the library. 4. Completing the installation— a. Attach the scsi cover plates ( s ) and the tape drive cover plate ( p ) that came with your replacement kit. See “reference illustrations” on page 3 . Library if your library has... Attach th...
Page 24
24 of 28 b. Reconfigure your library—you must reconfigure your library for your backup application to recognize the new tape drive. See page 25 for instructions. ! Important the library requires both the scsi cover plates ( s ) and the tape drive cover plates (p) for esd protection. Do not leave any...
Page 25
25 of 28 r econfiguring the l ibrary and r esuming o peration r econfiguring the l ibrary in order for the library to recognize the new tape drive, you must set the tape drive configuration to match the tape drives that are installed in the library. Note: do not connect the scsi cables at this time....
Page 26
26 of 28 4. Press modify. Press or until the selection arrow ( ) points to the desired configuration. Press select. Note: this menu option requires input for all of the tape drives installed in the library. If you press “back” before configuring all the tape drives, the configuration selection will ...
Page 27
27 of 28 the library communicates with the host through the scsi interface of one of the tape drive via the automation drive interface (adi) serial interface. See the tape drive’s product manual for tape drive information. See automation/drive interface – (adc) for adi information. 3. Reconnect the ...
Page 28
28 of 28 c onfirming the i nstallation you may want to perform a few load and unload operations and back up several megabytes of data to ensure that the library and the newly installed tape drive (or tape drives) are communicating correctly. Download and install the tools from www.Tandberg.Com the r...