1. DL manuals
  2. TANDBERG
  3. Receiver
  4. TT-1222
  5. Reference Manual

TANDBERG TT-1222 Reference Manual

Manual is about: 4:2:0 Professional Receiver, Software Version 2.0.0 (and later)

Summary of TT-1222

  • Page 1

    St.Re.Tt1222.2 issue 2 english (uk) reference guide tt1222 4:2:0 professional receiver software version 2.0.0 (and later) tt1222 4:2:0 professional receiver.

  • Page 2

    Preliminary pages page ii reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 issue 2 first published in 2005 by: t andberg t elevision l td r egistered a ddress : u nit 2 s trategic p ark , c omines w ay , h edge e nd , s outhampton , h ampshire , so30 4da u nited k ingdom registered...

  • Page 3: List of Contents

    Preliminary pages reference guide: tt1222 4:2:0 professional receiver page iii st.Re.Tt1222.2 list of contents chapter 1: introduction this chapter describes the purpose of the tt1222 in a typical system, provides a summary of its main features and identifies the controls. Chapter 2: installing the ...

  • Page 4: About This Reference Guide

    Preliminary pages page iv reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 about this reference guide this reference guide provides instructions and information for the installation and operation of the tt1222 4:2:0 professional receiver. It should be kept in a safe place for refer...

  • Page 5: Warnings, Cautions and Notes

    Preliminary pages reference guide: tt1222 4:2:0 professional receiver page v st.Re.Tt1222.2 warnings, cautions and notes heed warnings all warnings on the product and in the operating instructions should be adhered to. The manufacturer cannot be held responsible for injuries or damage where warnings...

  • Page 6

    Preliminary pages page vi reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 tandberg television customer services support services our primary objective is to provide first class customer care that is tailored to your specific business and operational requirements. All levels are su...

  • Page 7: Technical Training

    Preliminary pages reference guide: tt1222 4:2:0 professional receiver page vii st.Re.Tt1222.2 technical training training courses tandberg television provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies. Tandberg can provide ...

  • Page 8

    Preliminary pages page viii reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 9: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 1-1 st.Re.Tt1222.2 chapter 1 1. Introduction contents 1.1 scope of this reference guide................................ 1-3 1.1.1 who should use this reference guide....... 1-3 1.1.2 what equipment is covered by this reference guide .............

  • Page 10

    Introduction page 1-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 11: 1.1

    Introduction reference guide: tt1222 4:2:0 professional receiver page 1-3 st.Re.Tt1222.2 1.1 scope of this reference guide 1.1.1 who should use this reference guide this reference guide is written for operators/users of the tandberg tt1222 professional receiver. It describes the unit’s functions and...

  • Page 12: 1.2 Summary

    Introduction page 1-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 1.2 summary of features 1.2.1 main features the receiver is fully compliant with the appropriate sections of the mpeg-2 1 and dvb-s 2 specifications. The tt1222 offers the following features: • signal inputs: qp...

  • Page 13: 1.2.2 Outputs

    Introduction reference guide: tt1222 4:2:0 professional receiver page 1-5 st.Re.Tt1222.2 biss modes 1 and e • front panel controls and indications: a 2 row by 20 character back lit lcd display provides information and allows operator choice entry four pushbuttons provide the control interface in con...

  • Page 14: 1.2.3 Conditional

    Introduction page 1-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 1.2.3 conditional access the transport stream received by the ird may be encrypted. The ca system is used to decrypt the required components of the transport stream so that they can be decoded. The following con...

  • Page 15: 1.4 Guided

    Introduction reference guide: tt1222 4:2:0 professional receiver page 1-7 st.Re.Tt1222.2 1.4 guided tour 1.4.1 construction the receiver is constructed using a screened fan-ventilated chassis. All operational inputs and outputs are via the rear panel connectors. The unit may be operated freestanding...

  • Page 16: 1.4.3

    Introduction page 1-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 edit and save in the edit mode, when the correct value is in place, exit and save by pressing multiple times to the right, to move the cursor outside the edit area. When the cursor leaves the edit area, the new ...

  • Page 17: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 2-1 st.Re.Tt1222.2 chapter 2 2. Installing the equipment contents 2.1 read this first!.......................................................... 2-3 2.1.1 handling ....................................................... 2-3 2.1.2 installing th...

  • Page 18

    Installing the equipment page 2-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 table 2.8: rs-232 connector...................................................... 2-14 table 2.9: conditional access..................................................... 2-14.

  • Page 19: 2.1

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-3 st.Re.Tt1222.2 2.1 read this first! 2.1.1 handling the tt1222 must be handled and installed carefully and thoughtfully to prevent safety hazards and damage. 2.1.2 installing the equipment follow the instructions fo...

  • Page 20: 2.2 Preliminary

    Installing the equipment page 2-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 2.2 preliminary checks 2.2.1 mechanical inspection inspect the equipment for damage-in-transit. If in doubt, please contact tandberg television customer services (see preliminary pages). Warning… rem...

  • Page 21: 2.3.3

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-5 st.Re.Tt1222.2 care in positioning cautions… 1. The fan and openings contained within this unit are not fitted with a dust / insect filter. Pay attention to the environment in which it is to be used. 2. Do not inst...

  • Page 22: 2.4

    Installing the equipment page 2-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 2.4 emc compliance statements 1 2.4.1 en 55022 and as/nzs 3548 this is a class a product. In a domestic environment this product may cause radio interference in which case the user may be required to...

  • Page 23: 2.5.2 Technical

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-7 st.Re.Tt1222.2 note… there is no user-replaceable fuse in the rear of the unit. 2.5.2 technical earth the technical earth provides a suitable connection between the tt1222 and the installation to give a low impedan...

  • Page 24: 2.5.4

    Installing the equipment page 2-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 disposal of moulded plugs if the moulded plug fitted to the mains cable supplied with this equipment is not required, use another cable. If the supplied plug is to be changed, cut it off and dispose ...

  • Page 25: 2.6 Signal

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-9 st.Re.Tt1222.2 2.6 signal connections 2.6.1 overview figure 2.3 shows the signal connections for the tt1222 receiver and options. Tt1222 professional receiver option modules power supply unit ac mains supply condit...

  • Page 26: 2.6.3 Output

    Installing the equipment page 2-10 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 asi input (tt1222/hwo/asi/in) see chapter 3, options for details. Rs232 remote the rs-232 connector labelled remote on the back of the equipment allows for connection to a pc for remote control, sof...

  • Page 27

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-11 st.Re.Tt1222.2 table 2.4: analogue video connector item specification connector type 2 x bnc, female output format* pal (b, d, g, h, i, combination n, m) secam (b, g, h, k1, l) with line id secam (d,k) with field ...

  • Page 28

    Installing the equipment page 2-12 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 audio lead two audio cables are supplied with tt1222 units, as shown in figure 2.5. These cables support analogue left and right channels and unbalanced digital audio. Figure 2.5: audio cable asi ou...

  • Page 29

    Installing the equipment reference guide: tt1222 4:2:0 professional receiver page 2-13 st.Re.Tt1222.2 table 2.6: rs-232 low-speed data connector item specification connector type 9-way d-type, female connector designation rs232 data output rate 75, 110, 150, 200,300, 600, 1050, 1200, 2400, 4800, 960...

  • Page 30: 2.6.4 Rs232

    Installing the equipment page 2-14 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 2.6.4 rs232 remote the rs-232 connector labelled remote on the back of the equipment allows for connection to a pc for remote control, software upload or debug purposes. The setup ⇒ outputs ⇒ rs232 ...

  • Page 31: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 3-1 st.Re.Tt1222.2 chapter 3 3. Options contents 3.1 available options ...................................................... 3-3 3.1.1 hardware options......................................... 3-3 3.1.2 software options .........................

  • Page 32

    Options page 3-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 33: 3.1 Available

    Options reference guide: tt1222 4:2:0 professional receiver page 3-3 st.Re.Tt1222.2 3.1 available options 3.1.1 hardware options these options require extra hardware to be fitted to the unit. Contact the customer services helpdesk for details (see preliminary pages). Table 3.1 lists all the differen...

  • Page 34: 3.2

    Options page 3-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 3.2 hardware enabled input options 3.2.1 limitations the tt1222 can not be fitted with the asi input option and qpsk input option at the same time. 3.2.2 asi input (tt1222/hwo/asi/in) general the asi input card suppo...

  • Page 35

    Options reference guide: tt1222 4:2:0 professional receiver page 3-5 st.Re.Tt1222.2 cautions… 1. The receiver provides dc power via the active l-band input connector to drive an lnb (low noise block down-converter). Do not connect equipment other than an lnb to this connector. Failure to do this may...

  • Page 36: 3.3

    Options page 3-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 3.3 hardware enabled output options 3.3.1 asi output (tt1222/hwo/asi/out) general the tt1222 provides a single asi output on a bnc connector. Connector details 75 Ω bnc connector. Setting up the asi output the output...

  • Page 37

    Options reference guide: tt1222 4:2:0 professional receiver page 3-7 st.Re.Tt1222.2 output description field+notch chrominance subcarrier reference signals occupying nine lines of field-blanking period on lines 7 to 15 in fields 1 and 3 and lines 320 to 328 in fields 2 and 4. Also has a luminance tr...

  • Page 38

    Options page 3-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 39: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 4-1 st.Re.Tt1222.2 chapter 4 4. Operating the equipment locally contents 4.1 powering the equipment........................................... 4-3 4.1.1 switching on ................................................ 4-3 4.1.2 front panel keypad...

  • Page 40

    Operating the equipment locally page 4-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 41: 4.1

    Operating the equipment locally reference guide: tt1222 4:2:0 professional receiver page 4-3 st.Re.Tt1222.2 4.1 powering the equipment 4.1.1 switching on connect the tt1222 to the signal inputs and the ac power supply and turn it on. There is a short boot period. After the boot period, the unit disp...

  • Page 42: 4.2

    Operating the equipment locally page 4-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 4.2 using the local controls 4.2.1 menu tree see annex c, section c.2. 4.2.2 selecting a (sub)menu item selecting the menu item to select a menu item, navigate using the up and down arrow key ...

  • Page 43: 4.4 Service

    Operating the equipment locally reference guide: tt1222 4:2:0 professional receiver page 4-5 st.Re.Tt1222.2 4.4 service configuration 4.4.1 selecting a service setting up a service each transport stream may contain a multitude of services and types. The tv service and audio 2 service menus, located ...

  • Page 44: 4.4.2

    Operating the equipment locally page 4-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 4.4.2 setting up an additional audio channel configuring this output is very similar to configuring the tv output. Note… audio 1 is associated with the tv service. An additional audio is avail...

  • Page 45: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 5-1 st.Re.Tt1222.2 chapter 5 5. Operating the equipment remotely contents 5.1 remote control......................................................... 5-3 5.1.1 introduction................................................... 5-3 5.1.2 remote pr...

  • Page 46

    Operating the equipment remotely page 5-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 47: 5.1 Remote

    Operating the equipment remotely reference guide: tt1222 4:2:0 professional receiver page 5-3 st.Re.Tt1222.2 5.1 remote control 5.1.1 introduction the tt1222 can be remotely controlled in a variety of ways. The basic control methods are: • rs-232 control methods: tandberg device controller (tdc) thi...

  • Page 48: 5.2

    Operating the equipment remotely page 5-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 once the communication parameters are entered correctly, set the system into remote mode for the external computer to gain control of the unit. Table 5.2: activating rs-232 remote control ste...

  • Page 49: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 6-1 st.Re.Tt1222.2 chapter 6 6. Alarms/gpos contents 6.1 alarm configuration .................................................. 6-3 6.1.1 alarm configuration of the tt1222 .............. 6-3 6.1.2 changing the alarm configuration ................

  • Page 50

    Alarms/gpos page 6-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 51: 6.1 Alarm

    Alarms/gpos reference guide: tt1222 4:2:0 professional receiver page 6-3 st.Re.Tt1222.2 6.1 alarm configuration 6.1.1 alarm configuration of the tt1222 the tt1222 has a multitude of possible error conditions. All of these error conditions generate error messages, which are user configurable, and eac...

  • Page 52: 6.2

    Alarms/gpos page 6-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 table 6.2: navigating the alarm configuration menus step action result 1. Go to the alarm setup menu, located under setup ⇒ outputs ⇒ alarms ⇒ select alarms. The display will read “set:select alarms” on the top l...

  • Page 53: 6.3

    Alarms/gpos reference guide: tt1222 4:2:0 professional receiver page 6-5 st.Re.Tt1222.2 6.3 menu driven alarm indications once the tt1222 is in a warned or alarmed state, the easiest way for the user to diagnose the alarm condition is via the status menu. Table 6.3: navigating the alarm status menus...

  • Page 54: 6.5

    Alarms/gpos page 6-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 the outputs are not suitable for driving general purpose 5v relays which have a coil resistance of less than 167 Ω. The gpos can not be activated on power failure. 6.5 setting up the gpos configuration the tt1222...

  • Page 55

    Alarms/gpos reference guide: tt1222 4:2:0 professional receiver page 6-7 st.Re.Tt1222.2 table 6.6: navigating the gpo configuration menus step action result 1. Go to the gpo setup menu, located under setup ⇒ outputs ⇒ gpos. The display will read “set:gpos” on the top line. 2. Using the up and down a...

  • Page 56

    Alarms/gpos page 6-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 57: Contents

    Reference guide: tt1222 4:2:0 professional receiver page 7-1 st.Re.Tt1222.2 chapter 7 7. Preventive maintenance and fault- finding contents 7.1 routine checks......................................................... 7-3 7.1.1 cooling fan .................................................. 7-3 7.1.2 c...

  • Page 58

    Preventive maintenance and fault-finding page 7-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 59: 7.1 Routine

    Preventive maintenance and fault-finding reference guide: tt1222 4:2:0 professional receiver page 7-3 st.Re.Tt1222.2 7.1 routine checks 7.1.1 cooling fan there are no routine checks associated with this equipment other than to ensure that the unit is adequately cooled. This equipment must never be o...

  • Page 60: 7.2.2 Replacement

    Preventive maintenance and fault-finding page 7-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 7.2.2 replacement parts when replacement parts are required, be sure only parts specified by tandberg television (or having the same characteristics as the original part) have been us...

  • Page 61: 7.4

    Preventive maintenance and fault-finding reference guide: tt1222 4:2:0 professional receiver page 7-5 st.Re.Tt1222.2 7.4 factory default settings the tt1222 is dispatched with the following factory defaults. These can be restored at any time using the restore def: option found in the setup ⇒ system ...

  • Page 62: 7.5 Fault-Finding

    Preventive maintenance and fault-finding page 7-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 7.5 fault-finding 7.5.1 general the information contained in this chapter is intended to isolate the unit as the faulty equipment if a system failure occurs. If the following informat...

  • Page 63

    Reference guide: tt1222 4:2:0 professional receiver page a-1 st.Re.Tt1222.2 annex a a. Glossary the following list covers most of the abbreviations, acronyms and terms as used in tandberg television limited manuals, user and reference guides. All terms may not be included in this reference guide. µm...

  • Page 64

    Glossary page a-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b3zs bipolar with three zero substitution: a method of eliminating long zero strings in a transmission. It is used to ensure a sufficient number of transitions to maintain system synchronisation when the user data s...

  • Page 65

    Glossary reference guide: tt1222 4:2:0 professional receiver page a-3 st.Re.Tt1222.2 compression reduction in the number of bits used to represent the same information. For the purposes of a broadcast system, it is the process of reducing digital picture information by discarding redundant portions ...

  • Page 66

    Glossary page a-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 ebu european broadcast union. Ecm entitlement control message. Edi ethernet data input eia electronics industries association (usa). Eit event information table: equipment: a component of the dvb-service information...

  • Page 67

    Glossary reference guide: tt1222 4:2:0 professional receiver page a-5 st.Re.Tt1222.2 interframe coding compression coding involving consecutive frames. When consecutive frames are compared, temporal redundancy is used to remove common elements (information) and arrive at difference information. Mpeg...

  • Page 68

    Glossary page a-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 macroblock a 16x16-pixel area of the tv picture. Most processing within the mpeg domain takes place with macro blocks. These are converted to four 8x8 blocks using either frame dct or field dct. Four 8 x 8 blocks of...

  • Page 69

    Glossary reference guide: tt1222 4:2:0 professional receiver page a-7 st.Re.Tt1222.2 nvod near video on demand: method of offering multiple showings of movies or events. The showings are timed to start at set intervals, determined by the broadcaster. Each showing of a movie or event can be sold to s...

  • Page 70

    Glossary page a-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 programme a linking of one or more events under the control of a broadcaster. For example, football match, news, film show. In the mpeg-2 concept, the collection of elementary streams comprising the programme, have ...

  • Page 71

    Glossary reference guide: tt1222 4:2:0 professional receiver page a-9 st.Re.Tt1222.2 single packet burst mode a burst of asi bytes (either 188 or 204, depending on packet length) is contiguously grouped into an mpeg-2 transport stream packet. Stuffing data is added between the packets to increase th...

  • Page 72

    Glossary page a-10 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 ups uninterruptable power supply: a method of supplying backup power when the electrical power fails or drops to an unacceptable voltage level. Small ups systems provide battery power for a few minutes; enough to p...

  • Page 73: Contents

    Reference guide: tt1222 4:2:0 professional receiver page b-1 st.Re.Tt1222.2 annex b b. Technical specification contents b.1 general .....................................................................B-3 b.2 key features.............................................................B-3 b.3 video deco...

  • Page 74

    Technical specification page b-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 75: B.1 General

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-3 st.Re.Tt1222.2 b.1 general the tt1222 is a 1ru single channel mpeg-2 receiver, designed to decode dvb compliant mp@ml mpeg-2 transport streams. B.2 key features • optional inputs: qpsk, asi (refer to chapter 3 for d...

  • Page 76: B.4 Outputs

    Technical specification page b-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.4 outputs b.4.1 analogue video output two bnc composite analogue video outputs are provided on the rear panel of the unit. Table b.2: analogue video output parameter performance safety status: selv ...

  • Page 77: B.4.3

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-5 st.Re.Tt1222.2 chroma subcarrier blanking: a) from leading edge of line-blanking signal up to i = 5.6 ± 0.2 ( µ s) after epoch o h , b) during field-blanking interval, excluding frame identification signals, or, in ...

  • Page 78: B.4.5

    Technical specification page b-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.4.5 vbi 625 lines output table b.6: 625 line vbi output parameter line/field performance vits lines specification itu-r j.63 vits pal (lines) 17, 18, 330, 331 vits secam (lines) 17, 18 vitc lines 16...

  • Page 79: B.4.7 Audio

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-7 st.Re.Tt1222.2 b.4.7 audio decoder table b.8: audio decoder parameter performance supported formats: mpeg-1 layer 1, mpeg-1 layer 2 (musicam) dolby ac-3 downmix output format option: audio 1 and audio 2:balanced ana...

  • Page 80: B.5 Data

    Technical specification page b-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.5 data communication b.5.1 low speed data table b.11: ls data configuration parameter performance safety status: selv output connector: 9 pin d-sub (female) electrical format: rs-232 data rates: 75,...

  • Page 81: B.6

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-9 st.Re.Tt1222.2 b.6 alarm relay/general purpose output table b.13: alarm relay parameter specification safety status selv output connector female 9 pin d-sub electrical format mechanical relay, contact closure number...

  • Page 82: B.7 Options

    Technical specification page b-10 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.7 options b.7.1 qpsk input option (tt1222/hwo/qpsk) the satellite input interface shall be compliant with the dvb specification. The lnb supply shall meet the requirements of iec1319-1 (iec61319-1)...

  • Page 83: B.7.2

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-11 st.Re.Tt1222.2 b.7.2 asi input option (tt1222/hwo/asi/in) the asi interface is implemented in accordance with cenelec en 50083-9: ref [15], in particular annex b and e. Table b.16: asi input parameter specification...

  • Page 84: B.7.4

    Technical specification page b-12 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.7.4 russian secam output option (tt1222/hwo/rs) the russian secam output module offers itu-r bt470-6/gost 7845-92 compliant russian secam for systems d and k. When the module is fitted both cvbs ou...

  • Page 85: B.10 Environmental

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-13 st.Re.Tt1222.2 b.10 environmental conditions table b.20: environmental specification item specification operational temperature 0 °c to +50°c (14°f to 122°f) ambient with free air-flow relative humidity 0% to 95% (...

  • Page 86: B.11.2 Emc

    Technical specification page b-14 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 b.11.2 emc 6 the equipment has been designed and tested to meet the following: en 55022 and cispr22 european international emission standard limits and methods of measurement of radio frequency inter...

  • Page 87

    Technical specification reference guide: tt1222 4:2:0 professional receiver page b-15 st.Re.Tt1222.2 note... The c-tick mark was first affixed to this product in 2005. B.11.5 recommended cable types table b.21: recommended cable types signal type connector recommended cable cvbs 1 / cvbs 2 bnc canfo...

  • Page 88

    Technical specification page b-16 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 89: Contents

    Reference guide: tt1222 4:2:0 professional receiver page c-1 st.Re.Tt1222.2 annex c c. Front panel lcd menus contents c.1 lcd menus ...............................................................C-3 c.1.1 using the menus...........................................C-3 c.1.2 menu descriptions.............

  • Page 90

    Front panel lcd menus page c-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.6.11 pid info menu ............................................ C-34 c.6.12 tv service pid info menu.......................... C-34 c.6.13 audio 2 service pid info menu.................. C-35 c.6.14 c...

  • Page 91: C.1 Lcd

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-3 st.Re.Tt1222.2 c.1 lcd menus c.1.1 using the menus detailed description of the use of menus is given in chapter 4, operating the equipment locally. C.1.2 menu descriptions this annex describes the front panel lcd menu...

  • Page 92

    Front panel lcd menus page c-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 unlocking the front panel: the unlocking sequence is required if the locked indicator is present on the top left line. The sequence is left, right, left, left, left, right, right, right. Protected menus...

  • Page 93: C.2 Menu

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-5 st.Re.Tt1222.2 c.2 menu tree main menu presets > setup > status > properties > presets select > add > presets:select ->p00: program 1 _ p01: not used _ p63: not used presets:add _ p00: program 1 _ p01: not used _ p63:...

  • Page 94: C.3

    Front panel lcd menus page c-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.3 menu pages - main menu the main menu is a pure branching menu. No items are selectable in this menu, it only allows access to other, lower level menus, which are described in individual sections. Ta...

  • Page 95: C.4 Presets

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-7 st.Re.Tt1222.2 c.4 presets menu c.4.1 presets menu items provides access to menus that allow the user to store and retrieve service selections. Table c.2: presets menu menu title: presets description section select > ...

  • Page 96: C.5.2 Tv

    Front panel lcd menus page c-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 menu title: setup description section outputs > enters the outputs setup submenu. C.5.13 ca > enters the ca (conditional access) setup submenu c.5.25 system > enters the system submenu c.5.32 control > ...

  • Page 97: C.5.3

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-9 st.Re.Tt1222.2 menu title: set:tv service description section dvb pref: allows the selection of formatting the dvb subtitles in conjunction with format conversion and wide screen signalling. A preferred format can be ...

  • Page 98: C.5.5

    Front panel lcd menus page c-10 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 table c.8: audio2 service menu menu title: set:aud2 service description section service id > display or change the service id for the decoded service. C.5.5 track audio 1: audio 2 can be set to track a...

  • Page 99: C.5.7

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-11 st.Re.Tt1222.2 c.5.7 video 625 setup menu the video setup 625 menu contains all the parameters that affect the 625 line video, other than the basic selection of video service and language. Table c.11: video 625 setup...

  • Page 100

    Front panel lcd menus page c-12 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 menu title: set:video 625 description section wss: wide screen signalling. Selects decoding of the wss information into the vbi area. On (dvb) - wss will be regenerated as sent in the wss pid. Mpeg-vid...

  • Page 101

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-13 st.Re.Tt1222.2 menu title: set:video 625 description section secam * : enables the russian secam subcarrier reference signal to be configured. Lineid - chrominance subcarrier reference signals are inserted into the b...

  • Page 102: C.5.8

    Front panel lcd menus page c-14 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.8 video 525 setup menu the video setup 525 menu contains all the parameters that affect 525 line video, other than the basic selection of video service and language. Table c.12: video 525 setup men...

  • Page 103: C.5.9 Default

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-15 st.Re.Tt1222.2 c.5.9 default output menu if the receiver losses its input signal, input lock or has decoding errors, the video output will default to a legal output. Table c.13: default output setup menu menu title: ...

  • Page 104

    Front panel lcd menus page c-16 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.11 audio 1 (tv) and audio 2 setup menus the audio setup menus allows the user to configure and control each audio output. Table c.15: audio 1 and 2 setup menu menu title: set:audio 1, set:audio 2 d...

  • Page 105: C.5.12 Input

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-17 st.Re.Tt1222.2 the modulation of the audio depends both on the modulation used on the encoder side, and on the decoder side. Table c.16 below lists what is output on the decoder, in correlation to the modulator setti...

  • Page 106

    Front panel lcd menus page c-18 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 table c.18: asi input setup menu menu title: set:input description section asi: no setup req. No set-up is available when the asi input card is fitted. ---- qpsk input the qpsk menu contains all the it...

  • Page 107: C.5.13  Outputs Setup Menu

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-19 st.Re.Tt1222.2 c.5.13 outputs setup menu the number of items available in this menu is dependent on the output cards fitted inside the receiver. The items that are not standard are indicated with *. Table c.21: outpu...

  • Page 108: C.5.16  Cvbs Output Menu

    Front panel lcd menus page c-20 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.16 cvbs output menu table c.24: cvbs output menu menu title: set: cvbs output description section alarm state: selects the format of the cvbs output if an alarm is raised. Sync - the cvbs output wi...

  • Page 109: C.5.18 Gpo

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-21 st.Re.Tt1222.2 c.5.18 gpo x menu one or more of these can be set to trigger a single gpo. The list of available triggers are the same for the each gpo. Table c.26: gpo trigger setup menu menu title: set: gpo x descri...

  • Page 110: C.5.20  Remote Port Menu

    Front panel lcd menus page c-22 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.20 remote port menu the remote port menu contains the parameters that have to be configured for a remote control computer / device to work correctly. Note… tandberg television’s remote control or s...

  • Page 111: C.5.21 Ls

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-23 st.Re.Tt1222.2 c.5.21 ls data menu the ls data menu configures the parameters for the output of rs-232 data, extracted from the transport stream. Table c.29: ls data setup menu menu title: set:ls data description sec...

  • Page 112: C.5.22  Data Port Menu

    Front panel lcd menus page c-24 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.22 data port menu the data port menu contains the controls for the physical output of the ls data. The settings configured here, need to match the settings on the device set up to receive the ls da...

  • Page 113: C.5.23  Ls Output Menu

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-25 st.Re.Tt1222.2 c.5.23 ls output menu the ls data output menu controls the output format and buffering of the low speed data. Table c.31: ls data output setup menu menu title: set:rs232 ls o/p description section o/p ...

  • Page 114: C.5.25 Ca

    Front panel lcd menus page c-26 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.25 ca menu this menu contains all ca setup parameters. Table c.33: ca setup menu menu title: set:ca description section ca mode: sets the ca mode to be used on the receiver. Standard – uses common ...

  • Page 115: C.5.28  Biss 1 Menu

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-27 st.Re.Tt1222.2 c.5.28 biss 1 menu this menu is the key entry menu for biss 1 set-up. Table c.36: biss 1 setup menu menu title: set:tv biss 1 and set:aud2 biss 1 description section key: the 12 digit biss key can be e...

  • Page 116: C.5.32 System

    Front panel lcd menus page c-28 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.5.32 system menu the system options menu contains the parameters necessary to configure detailed operational aspects of the unit. Table c.40: system setup menu menu title: set:system description sect...

  • Page 117: C.5.34 Factory

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-29 st.Re.Tt1222.2 menu title: set:control description section menu lock: activates or disables the menu lock. On - menu lock activated. Once activated, an 8 key combination has to be entered to allow access to the menus...

  • Page 118: C.6.3

    Front panel lcd menus page c-30 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 menu title: stat:alarm description section dvb subt enters the dvb subtitle alarm status submenu annex d audio1 enters the audio 1 alarm status submenu annex d audio2 enters the audio 2 alarm status su...

  • Page 119: C.6.5 Signal

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-31 st.Re.Tt1222.2 asi input table c.45: input status menu, asi input menu title: stat:input description section lock: indicate whether the input is locked. Options are: locked and not locked ---- qpsk input table c.46: ...

  • Page 120: C.6.8

    Front panel lcd menus page c-32 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 table c.49: video status menu menu title: stat: video description section hsize: display the horizontal resolution of the video. ---- vsize: display the vertical resolution of the video. ---- eff. Rate...

  • Page 121: C.6.9 Vbi

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-33 st.Re.Tt1222.2 c.6.9 vbi status menu the vbi status menu displays the current status of the vbi components. Table c.51: vbi status menu menu title: stat: vbi description 525 625 teletext: show the current status of t...

  • Page 122: C.6.10  Data Status Menu

    Front panel lcd menus page c-34 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.6.10 data status menu the data menu shows the current status of the data component. Table c.52: data status menu menu title: stat:data description section buff use %: shows the usage, in percent, of ...

  • Page 123: C.6.14 Ca

    Front panel lcd menus reference guide: tt1222 4:2:0 professional receiver page c-35 st.Re.Tt1222.2 c.6.13 audio 2 service pid info menu shows the audio pid associated with the currently selected audio2 service, if present. Table c.55: audio2 service pid info menu menu title: stat:aud2 pid info descr...

  • Page 124: C.7.2 Hw

    Front panel lcd menus page c-36 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 c.7.2 hw config menu lists the available features and hardware of the unit. A “+” in front of the component, signifies that the component is present. A “-“ in front of the component, signifies that the...

  • Page 125: Contents

    Reference guide: tt1222 4:2:0 professional receiver page d-1 st.Re.Tt1222.2 annex d d. Alarm categories and conditions contents d.1 alarm conditions.......................................................D-3 d.2 input stage alarms....................................................D-3 d.2.1 qpsk inpu...

  • Page 126

    Alarm categories and conditions page d-2 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.

  • Page 127: D.1 Alarm

    Alarm categories and conditions reference guide: tt1222 4:2:0 professional receiver page d-3 st.Re.Tt1222.2 d.1 alarm conditions this chapter lists the alarm conditions detected by the unit. It also lists a description for the alarm, a possible remedy, and the default state of the alarm in the alarm...

  • Page 128: D.3

    Alarm categories and conditions page d-4 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 d.3 output stage alarms d.3.1 video output alarms the video output alarms relate to errors occurring in the video stream decoder. Table d.3: video alarm categories and conditions alarm categor...

  • Page 129: D.3.3 Vbi

    Alarm categories and conditions reference guide: tt1222 4:2:0 professional receiver page d-5 st.Re.Tt1222.2 alarm category contents pts starvation cannot obtain lipsync according to pcr/pts due to compressed bit buffer underflow. A pts overflow cannot obtain lipsync according to pcr/pts due to compr...

  • Page 130: D.3.4 Data

    Alarm categories and conditions page d-6 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 d.3.4 data output alarms the data output alarms reflect the status of the ls data (rs-232) output port and its associated functions. Table d.6: data output alarm categories and conditions alar...

  • Page 131: D.4.2

    Alarm categories and conditions reference guide: tt1222 4:2:0 professional receiver page d-7 st.Re.Tt1222.2 d.4.2 psi/si related alarms contains information about the currently processed psi/si arriving at the decoder. Table d.8: psi/si related alarm categories and conditions alarm category contents...

  • Page 132

    Alarm categories and conditions page d-8 reference guide: tt1222 4:2:0 professional receiver st.Re.Tt1222.2 blank.