Summary of CDP-50
Page 1
Operation manual cdp-50 cd-player.
Page 2
01 accessories accessories 1 x cdp-50 1 x remote control 2 x batteries (optional) 1 x operation manual this operation manual supplies all the information that you need to have about your tangent cdp-50. Please read this operation manual carefully before you start using the unit! ++ + operation manua...
Page 3
02 contents accessories accessories 01 contents contents 02 safety precautions safety precautions 03 important safety instructions important safety instructions 04 important information important information 06 connection connection to the mains 07 remote control installation of batteries 08 using t...
Page 4
To minimise the risk of fire or electrical shock, do not expose the unit to rain or moisture. Do not open the cabinet as it contains dangerous voltage. Only qualified technicians are allowed to carry out repair and service. If the plug of the power cord needs to be replaced, it is important that the...
Page 5
Warning: it is important that you read and observe both the instructions in this manual and the instructions on the unit. Keep this manual for future reference. This unit was designed and manufactured with a view to providing maximum safety for the user. Incorrect use of the unit may cause electrica...
Page 6
Service do not attempt to carry out any service work yourself. By opening or removing the cabinet, you will be exposed to dangerous voltage or other hazards. Any service work should be carried out by qualified technicians. Spare parts if spare parts are required, make sure that the service technicia...
Page 7
Important information handling instructions the top and back panel of the unit may become warm after prolonged use. This is not due to a defect. Turn off the power when the unit is not used. Protect the power cord follow the instructions below to prevent abnormal operation, electrical shock, fire or...
Page 8
07 connection do not turn on the power before all connections have been made correctly. Check that all connections have been made correctly before turning on the power. Check that the mains voltage is 230-240v ac50hz before turning on the power. Connection to the mains check that all other connectio...
Page 9
08 remote control installation of batteries remove the cover as illustrated. Position two batteries of the type aaa/r03/um4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). Replace the cover. Do not mix new and old batteries and do not u...
Page 10
09 some of the functions of the unit can only be performed by means of the remote control. Some functions are connected with the selected signal input source. Some buttons on the remote control may therefore not be available if the corresponding signal input source has not been selected. + + + remot...
Page 11
8 9 10 1 2 3 4 5 6 7 10 front panel and connections front panel mains switch: used to interrupt the mains voltage. Led indicator: lights green when the unit is turned on. Lights red when the unit is in standby mode or in operation. Program: makes it possible to play the tracks of a cd a certain orde...
Page 12
11 front panel and connections connections 1 2 3 stereo output: analogue stereo output. For connection to stereo amplifier or receiver with analogue input. Optical output: optical spdif output. For connection to stereo amplifier or receiver with digital input. Ac input: for connection of mains volta...
Page 13
12 connection audio connection layout subwoofer (optional) phono tuner dvd cd aux 1 aux 2 function volume power headphone amp-50 amplifier analog amplifier/receiver this page contains only suggestions for connection of your eltax cdp-50. Note that the accessories in the pictures on this page are not...
Page 14
13 operation and functions phono power cdp-50 cd-player 1 3 3 turn on the unit by pressing the mains switch. Press the standby button on the remote control to switch to standby mode. The display will turn off and all functions will be reduced to a minimum to make sure that the unit uses minimal powe...
Page 15
14 operation and functions pause - 8 8 4 - 0:38 press the play/pause button once more to stop playback. The small play symbol will disappear, and a small pause symbol will be displayed instead. To continue playback, press the play/pause button again. Stop/clear - 8 8 15 -58:34 to stop playback compl...
Page 16
15 operation and functions forward and rewind - 8 8 5 - 2:35 it is possible to perform a search in the track played. If you wish to search forward, depress the >> (next) button until you get to that part of the track that you wish to hear. You will see that the time counter in the display counts up ...
Page 17
16 operation and functions program repeat - 8 8 15 -58:34 the cdp-50 can be programmed to play the tracks of a cd in a certain order. Press the program button when playback has been stopped. The memory symbol and "pr p:01" will be displayed. Use > to select the track that you wish to include in the ...
Page 18
17 troubleshooting troubleshooting problem cause/remedy no power when unit is turned on. - switch on the electric current at the socket. - check that the plug has been correctly inserted into the socket. - the internal fuse has blown and must be replaced by a qualified service technician. - the powe...
Page 19
18 technical data technical data output voltage 0.7v+/-2db frequency characteristics (reference: 1khz 0db) 20 hz 0db -0.5 db +/- 1 db 100 hz 0db 0 db +/- 1 db 10 khz 0db -0.5 db +/- 2 db 20 khz 0db -3.0 db +/- 2 db channel balance separation > 60 db harmonious distortion (t h d + noise) signal/noise...
Page 20
Www. .Com tangent-audio.