Summary of MCS-600
Page 1
Instruction manual mcs-600
Page 2
This operation manual supplies all the information that you need to have about your tangent mcs-600. Please read this operation manual carefully before you start using the unit! 02 the objective of every tangent product is that fundamentally correct design can produce a product capable of achieving ...
Page 3
Contents 03 safety precautions 4 important safety instructions 5 important information 7 connection to the mains 8 front and rear panel functions 9 front panel functions 9 rear panel functions 10 remote control 11 installation of batteries 11 using the remote control 11 remote control functions 12 c...
Page 4
To minimise the risk of fire or electrical shock, do not expose the unit to rain or moisture. Do not open the cabinet as it contains dangerous voltage. Only qualified technicians are allowed to carry out repair and service. If the plug of the power cord needs to be replaced, it is important that the...
Page 5
Warning: it is important that you read and observe both the instructions in this manual and the instructions on the unit. Keep this manual for future reference. This unit was designed and manufactured with a view to providing maximum safety for the user. Incorrect use of the unit may cause electrica...
Page 6
Service do not attempt to carry out any service work yourself. By opening or removing the cabinet, you will be exposed to dangerous voltage or other hazards. Any service work should be carried out by qualified technicians. Spare parts if spare parts are required, make sure that the service technicia...
Page 7
Important information handling instructions - the top and back panel of the unit may become warm after prolonged use. This is not due to a defect. - turn off the power when the unit is not used. Protect the power cord - follow the instructions below to prevent abnormal operation, electrical shock, f...
Page 8
Connection to the mains connection to the mains do not turn on the power before all connections have been made correctly. Check that all connections have been made correctly before turning on the power. Check that the mains voltage is 220-240v ac50~60hz before turning on the power. (us version 110-1...
Page 9
Front and rear panel functions 09 1 5 3 4 6 7 8 9 10 11 12 13 14 15 16 1. Standby led 2. Power standby 3. Vfd display 4. 5. Tuning +/- 6. Station 7. Source 8. Repeat 9. Previous (i 10. Next (>>i) 11. Play/pause 12. Open/close/stop 13. Phones 14. Disc tray 15. Line in 16. Aux 2 the standby led indica...
Page 10
Front and rear panel functions 10 the points below contains a brief description of the rear panel buttons, inputs and outputs. For more detailed descriptions of the functions and connections, please see the following pages of the manual. Rear panel functions 1. Mains power switch. 2. Mains power inp...
Page 11
Remote control installation of batteries 1 remove the battery cover as illustrated. 2 position two batteries of the type aaa/r03/um4 in the battery compartment. Make sure that the orientation of the batteries is correct (see drawing at bottom). 3 replace the battery cover. - do not mix new and old b...
Page 12
Remote control 12 1. Power press the power button to set the receiver into standby. The standby led will turn red. Press the power button once again, to turn on the receiver on again. The standby led will turn green. Use these buttons to select radio presets or cd tracks. Use this button to store a ...
Page 13
Remote control 13 9. Tuning and station buttons tuning +/-: station +/-: 10. Treble 11. Bass 12. Display 13. Loudness 14. Stop 15. Pause 16. Fast reverse 17. Previous 18. Open/close 19. +10 20. Aps 21. Pty search use this button to manually search up and down in frequency for radio stations. Press t...
Page 14
Connections 14 before connection speaker connections caution: before connection turn off the power of all the equipment. Read instructions of each component you intend to connect to this unit. Be sure to insert each plug securely. To prevent hum and noise, do not bundle the interconnection leads wit...
Page 15
Connections 15 speaker 6-8ohm r l fm 75 w fm 75 w am loop class 1 laser procuct tape in dvd in aux 1 in on power off antenna audio model: mcs-600 power rating: ac 220v - 240v~50hz max power consumption:120w 220-240v ~50hz sub line out rec out left right tape player/recorder cd player dvd player mcs-...
Page 16
Speaker 6-8ohm r l fm 75 w fm 75 w am loop class 1 laser procuct tape in dvd in aux 1 in on power off antenna audio model: mcs-600 power rating: ac 220v - 240v~50hz max power consumption:120w 220-240v ~50hz sub line out rec out left right using the radio 16 connecting an antenna before you can start...
Page 17
Using the radio 17 rds is a method for the transmission of additional information from radio stations. It is only available in fm mode. For example, the name of the radio station, the name of the program or the type of program can be shown on the display. It functions only when the broadcasting stat...
Page 18
Troubleshooting 18 to determine any problem with your receiver, always check the most obvious possible causes first. If your problem still remains after your having checked the items below, consult your nearest dealer. Possible cause the left and right front speakers have been connected wrong/switch...
Page 19
Technical specifications 19 audio section line input woofer output fm tuner section am tuner section general dimensions weight kg (net) audio power output 2 x 60w output impedance front (l/r) 4-8 ohm total harmonic distortion less than 0.2% input sensitivity/impedance 200mv/47kohms frequency respons...
Page 20
For further information please visit our website: www.Tangent-audio.Com item no. 40527 service hotline +45 9641 1599.